Review this table to find
service needed, should be performed by a Sears or other qualified service agent.
WARNING
Always turn off and unplug vacuum cleaner before performing maintenance to the
vacuum | cleaner. | Fallure to do so could result in electrlcal | shock or personal | injury. |
Vacuum | cleaner won't | ]. | Unplugged at wall outlet. | I. | Plug in firmly, | press ON/OFF | switch. | |||||
start. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2. | Tripped circuit | breaker/blown | 2. | Reset circuit | breaker or | replace fuse. | ||||
|
|
| fuseat | household service panel. |
|
|
|
|
|
| ||
|
| 3. | Loose hose electrical | 3. | Reconnect hose ends. |
|
| |||||
|
|
| connections. |
|
|
|
|
|
|
| ||
Poor job | of dirt | 1. | Full or clogged | dust bag. | I. | Change bag. |
|
|
| |||
|
| 2. | Clogged airflow passages. | 2. | Clear airflow | passages. |
|
| ||||
|
| 3. | Dirty | filters. |
| 3. | Change filters. |
|
| |||
|
| 4. | Wrong | pile height setting. | 4. | Adjust | setting. |
|
| |||
|
| 5. | Wrong | power | level selected. | 5. | Adjust | control. |
|
| ||
|
| 6. | Hole | in hose. |
| 6. | Replace hose. |
|
| |||
|
| 7. | Worn |
| PowerMate agitator. | 7. | Change agitator. |
|
| |||
|
| 8. | Worn |
| or broken belt. | 8 & 9. | See BELTCHANGING AND |
| ||||
|
| 9. | Dirty | agitator | or end caps. |
| AGITATOR CLEANING. |
|
| |||
|
| 10. | Canister hood | open. | 10. | Close and latch hood. |
|
| ||||
|
| 11. | Tripped overload protector in | 11. | Remove any | items that may | be | |||||
|
|
| PowerMate. |
|
| caught | or jammed, then | reset. If | ||||
|
|
|
|
|
|
|
| vacuum cleaner starts and stops | ||||
again, clean agitator and end caps, then reset.
Vacuum cleaner starts | I. | Hose or | hood electrical |
| |
but shuts off. |
| connections. |
|
| |
| 2. | Tripped | overload | protector | in |
|
| PowerMate. |
|
| |
| 3. | Tripped | thermal | protector |
|
|
| in canister. |
|
| |
PowerMate will not | 1. | PowerMate connections |
| ||
run when attached. |
| unplugged. |
|
| |
| 2. | Worn or broken | belt. |
| |
| 3. | Dirty agitator or end caps. |
| ||
| 4. | Tripped | overload | protector | in |
|
| PowerMate. |
|
| |
| 5. | Vacuum | cleaner | in BARE |
|
|
| FLOOR mode. |
|
| |
I.Check connections, reconnect hose ends.
2.Remove any items that may be caught or jammed, then reset. If vacuum cleaner starts and stops again, clean agitator and end caps, then reset.
3.See PERFORMANCE FEATURES- "Thermal Protector."
]. Plug in firmly.
2&3. See BELTCHANGING AND
AGITATOR CLEANING.
4.Remove any items that may be caught or jammed, then reset. If vacuum cleaner starts and stops again, clean agitator and end caps, then reset.
Press CARPET/BARE FLOOR
button to change to CARPET mode.
- 23 -
