INSTALLATION STEP 6

Install the Door Control

Locate door control within sight of door, at a minimum height of 5 feet where small children cannot reach, away from moving parts of door and door hardware. If installing into drywall, drill 5/32" holes and use the anchors provided. For pre-wired installations (as in new home construction), it may be mounted to a single gang box (Figure 2).

1.Strip 1/4" of insulation from one end of bell wire and connect to the two terminal screws on back of door

control by color: white to 2 and white/red to 1.

2.Pry off cover along one side with a screwdriver blade (see Figure 1). Fasten with

6ABx1-1/4" self-tapping screws (standard installation) or 6-32xl" machine screws (into gang box) as follows:

•Install bottom screw, allowing 1/8" to protrude above wall surface.

•Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.

•Drill and install top screw with care to avoid cracking plastic housing. Do not over tighten.

•Insert top tabs and snap on cover.

3.(For standard installation only) Run bell wire up wall and across ceiling to motor unit. Use insulated staples to secure wire in several places. Be careful not to pierce wire with a staple, creating a short or open circuit.

4.Connect the bell wire to the terminal screws on the motor unit panel: white to 2; white/red to 1.

5.Position the antenna wire as shown.

6.Use tacks or staples to permanently attach entrapment warning label to wall near door control, and manual release/safety reverse test label in a prominent location on inside of garage door.

DO NOT connect power and operate opener at this time. The trolley will travel to the full open

To prevent possible SERIOUSINJURYor DEATHfrom electrocution:

•Be sure power is not connected BEFOREinstalling door control.

•Connect ONLYto 24 VOLT low voltage wires.

To prevent possible SERIOUSINJURYor DEATHfrom a closing garagedoor:

•Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet, and awayfrom all moving parts of door.

•NEVERpermit children to operate or play with door control push buttons or remote control transmitters.

•Activate door ONLYwhen it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

•ALWAYSkeep garagedoor in sight until completely closed. NEVERpermit anyoneto cross path of closing garagedoor.

Outside Keylock Accessory Connections

To opener terminal screws: white to 2; white/red to 1

HARDWARE SHOWN ACTUAL SIZE

 

Control

Console

(std instaliation)

Insulated

 

Staples

 

 

 

 

 

 

Control

Console

(pre-wired)

Dry Wail Anchors

Figure

1

 

 

Figure

2

REMOVE

& REPLACE COVER

PRE-WIRED

 

 

 

 

INSTALLATION

Insert Top

 

 

To Remove

 

Tabs Firsl

/ / z

 

Twist

Here

 

position but will not return to the close position until the sensor beam is connected and properly aligned.

TO Replace, ?_

24 Volt

 

2-Conductor

 

Bell Wire in

 

Gang Box

Lighted

Push Button

Top

Mounting

Hole

 

Terminal

"""""_

> Screws

 

Bottom

 

Mounting

Wire

Hole

 

BACK

VIEW

PREMIUM CONTROL CONSOLE

Back Panel

of Opener

18

Page 17 Page 19
Page 18
Image 18
Sears 139.53975SRT1, 139.53962SRT1 owner manual Install the Door Control, Std instaliation
Page 17 Page 19

139.53975SRT1, 139.53962SRT1 specifications

The Sears 139.53962SRT1 and 139.53975SRT1 are two sophisticated garage door opener models that have gained significant attention for their innovative features and technologies. These devices represent the cutting edge of convenience and security in residential garage systems.

One of the standout features of both models is the integrated MyQ technology. This allows users to control their garage doors remotely using a smartphone app, ensuring seamless access even when they are away from home. Whether you’re on vacation or simply running errands, the ability to monitor and control your garage door from anywhere adds an unmatched level of convenience and peace of mind.

Both the 139.53962SRT1 and 139.53975SRT1 come equipped with a powerful ¾ HP motor. This robust motor provides sufficient lifting power for standard-sized garage doors, ensuring efficient and reliable operation. The powerful motor is designed to handle heavy doors with ease, making it a suitable choice for a variety of residential applications.

Safety is a critical aspect of garage door systems, and these models excel in this area. They feature advanced safety sensors that detect obstructions in the door’s path. This means that if something is in the way as the garage door closes, it will automatically reverse, preventing potential accidents and injuries.

In addition to safety sensors, both models are equipped with rolling code technology. This system enhances security by changing the access code every time the remote is used, preventing unauthorized access and potential break-ins.

Another noteworthy characteristic of these garage door openers is their quiet operation. Thanks to a specially designed belt drive system, both models minimize noise during operation, making them ideal for homes with living spaces situated above the garage.

Installation is made simpler with the inclusion of detailed instructions and user-friendly components, allowing most homeowners to set up the system with minimal hassle.

Overall, the Sears 139.53962SRT1 and 139.53975SRT1 garage door openers combine powerful performance with advanced technology, safety features, and ease of use, making them top choices for anyone looking to upgrade their garage door system.
Top Page Image Contents