OPERATION
IMPORTANT SAFETY INSTRUCTIONSTo reduce the risk of severe injury or death:1.READAND FOLLOWALLWARNINGSAND
INSTRUCTIONS.
2.ALWAYSkeep remote controls outof reach of children.
NEVERpermit childrento operate or playwith garage
door control push buttons or remote controls.
3.ONLY activate garagedoor when it canbe seen clearly, it
is properly adjusted, and there areno obstructions to
door travel.
4.ALWAYSkeep garage door in sight until completely
closed.NO ONESHOULDCROSSTHEPATHOF THE
MOVINGDOOR.
5.NO ONESHOULD GOUNDERA STOPPED,PARTIALLY
OPENDOOR.
6. If possible,use emergencyrelease handleto disengage
trolley ONLYwhen garagedoor is CLOSED.Weakor
brokensprings or unbalanced door could result in an
opendoor falling rapidlyand/or unexpectedly.
7.NEVERuse emergency releasehandleunless garage
doorway is clear of persons and obstructions.
8.NEVERuse handleto pull garagedoor open or closed. If
rope knot becomes untied, you could fall.
9. If onecontrol (force or travel limits) is adjusted, the
othercontrol may also need adjustment.
10.After ANY adjustments are made,the safety reversal
systemMUST be tested.
11.Safety reversalsystem MUST be tested every month.
Garagedoor MUST reverse on contact with one-inch
(2.5 cm) high object (or a 2 x 4 laid flat) onthe floor.
12.ALWAYSKEEPGARAGEDOORPROPERLYBALANCED
(seepage 3). An improperly balanceddoor may not
reversewhen required and could result in SEVERE
INJURYor DEATH.
13.All repairsto cables, spring assemblies andother
hardware,all of which are under EXTREMEtension,
MUSTbe made by a trained door systems technician.
14.ALWAYSdisconnect electric powerto garagedoor
openerBEFOREmakingany repairs or removing
covers.
15.SAVETHESE INSTRUCTIONS.Using Your Garage Door Opener
Your Security+ opener and hand-held remote control
have been factory-set to a matching code which
changes with each use, randomly accessing over
100 billion new codes. Your opener will operate with
up to eight Security+ remote controls and one
Security÷ Keyless Entry System. If you purchase a
new remote, or if you wish to deactivate any remote,
follow the instructions in the Programming section.
Activate your opener with any of the following:
•The hand-held Remote Control: Hold the large
push button down until the door starts to move.
• The wall-mounted Door Control: Hold the push
button down until the door starts to move.
• The Keyless Entry (See Accessories): If provided
with your garage door opener, itmust be
programmed before use. See Programming.
When the opener is activated (with the safety
reversing sensor correctly installed and aligned)
1.If open, the door will close. If closed, it will open.
2. If closing, the door will reverse.
3. If opening, the door will stop.
4. If the door has been stopped ina partially open
position, it will close.
5. If obstructed while closing, the door will reverse. If
the obstruction interrupts the sensor beam, the
opener lights will blink for five seconds.
6. If obstructed while opening, the door will stop.
7. Iffully open, the door will not close when the beam
is broken. The sensor has no effect in the opening
cycle.
If the sensor is not installed, or is misaligned, the
door won't close from a hand-held remote. However,
you can close the door with the Door Control, the
Outdoor Key Switch, or Keyless Entry, if you activate
them until down travel is complete. If you release
them too soon, the door will reverse.
The opener lights will turn on under the following
conditions: when the opener is initially plugged in;
when power is restored after interruption; when the
opener is activated.
They will turn off automatically after 4-1/2 minutes or
provide constant light when the Light feature on the
Premium Control Console is activated. Bulb size is
75 watts maximum.
Security÷ Light Feature: Lights will also turn on
when someone walks through the open garage door.
With a Premium Control Console, this feature may be
turned off as follows: With the opener lights off, press
and hold the light button for 10 seconds, until the
light goes on and off again. To restore this feature,
start with the opener lights on, then press and hold
the light button for 10 seconds until the light goes off,
then on again.
31