Sharp AL-1215 1, 2

63

8

MISFEED REMOVAL

When the misfeed ( ) indicator blinks or blinks in the display, the unit will

stop because of a misfeed. If a misfeed occurs when using the SPF/RSPF, a number

may appear in the display after a minus sign. This indicates the number of the

originals that must be returned to the original feeder tray after a misfeed. Return the

required number of originals. Then this number will disappear when copying is

resumed or the clear ( ) key is pressed. When the SPF/RSPF misfeeds an

original sheet, the unit will stop and the SPF/RSPF misfeed ( ) indicator will blink,

while the misfeed ( ) indicator will remain off. For a misfeed of originals in the SPF/

RSPF, see "E: Misfeed in the SPF/RSPF" (p.66).

1Open the multi-bypass tray (AL-1551CS), and side cover, in that

order.

To open the multi-bypass tray, see "The multi-bypass tray (AL-1551CS)"

(p.17). To open the side cover, see "INSTALLING THE TD CARTRIDGE"

(p.10).

2Check the misfeed location. Remove the misfed paper

following the instructions for each location in the illustration

below. If the misfeed ( ) indicator blinks, proceed to "A:

Misfeed in the paper feed area" (p.64).

If the unit is turned on with the lower side cover open, the misfeed ( )

indicator will blink. In this case, close the lower side cover. The misfeed

( ) indicator will go out.

If paper is misfed here, proceed to "A:

Misfeed in the paper feed area". (p.64)

If paper is misfed here, proceed

to "D: Misfeed in the lower

paper feed area". (p.66)

If paper is misfed here, proceed to "B:

Misfeed in the fusing area". (p.64)

If the misfed paper is seen from

this side, proceed to "C: Misfeed

in the transport area". (p.65)

AL-1215_1530-1551CS.book 63 ページ２００２年８月７日　水曜日　午前９時３４分

Contents

Main AL-1215 AL-1530CS AL-1540CS AL-1551CS FOR YOUR PROTECTION... 1 CAUTIONS Caution label on the unit Cautions on using Warning: Cautions on handling Trademark acknowledgements Safety precautions: CONTENTS 1INTRODUCTION 2SETTING UP THE UNIT 8 4 1 4 USING THE MANUALS Online manual (AL-1530CS, AL-1540CS, AL-1551CS) How to use the online manual 5 PART NAMES 6 OPERATION PANEL 2 7 SETUP PROCEDURE 1 2 3 Page 5 6 12 POWER ON About the scan head Initial settings of operation panel Power off methods 3 14 PAPER 15 LOADING THE PAPER TRAY 1 2 3 4 5 under the corner hooks. 6 17 BYPASS FEED (including special paper) 1 2 Print face 3 The single bypass (AL-1215/AL-1530CS/AL-1540CS) Print face 1 2 4 19 CD-ROM SOFTWARE FOR THE SHARP PERSONAL MFP SERIES MFP driver 20 HARDWARE AND SOFTWARE REQUIREMENTS BEFORE INSTALLATION 21 Flow of installation 2 4 5 6 1 2 7 8 9 10 connect the USB interface cable or parallel interface cable. (p.45) 11 1 2 2 4 5 6 7 8 1 2 3 4 2 4 5 6 7 setup (This step will start if it was selected in step 4). 6 1 2 1 2 3 4 5 31 INDICATORS ON THE OPERATION PANEL SCANNER indicator ONLINE indicator Start indicator 1 2 3 4 How to print 1 2 3 4 34 1 2 3 4 1 2 3 4 5 Scan Button Destination Setting Dialog Box Flow of the Button Manager setting Page 1 2 3 4 Opening the scanner driver and scanning from your computer Using the SHARP TWAIN 1 RSPF. 3 4 5 1 2 3 4 5 Page 44 USING OTHER INSTALLED DRIVERS 1 2 3 4 5 6 1 2 3 Connecting the parallel interface cable 1 2 3 4 5 46 COPY FLOW 2 Place the original. 4 Start copying. 1 2 the original scale and the centering ( ) mark. Gently close the original cover/SPF/RSPF. mark Using the SPF/RSPF 1 2 Original face up of originals. 3 original feeder tray. Stream feeding mode 1 2 Automatic exposure adjustment 1 2 3 4 5 1 2 select the desired copy ratio. 3 6 52 ABOUT THE SPECIAL FUNCTIONS OF AL-1551CS Turn on Short EdgeTurn on Long Edge Two sided copying 3 ABC (p.49), "EXPOSURE ADJUSTMENT/PHOTO COPYING" (p.49), and "REDUCTION/ENLARGEMENT/ZOOM" (p.51). 1 2 1 2 55 3 4 USER PROGRAMS 2 3 4 56 5 6 DISPLAYING TOTAL NUMBER OF COPIES 7 57 TD CARTRIDGE REPLACEMENT 1 2 4 DRUM CARTRIDGE REPLACEMENT 1 2 3 4 window "INSTALLING THE TD CARTRIDGE" (p.10). 5 CLEANING THE UNIT Page 8 61 TROUBLESHOOTING If any problem occurs, check the list below before contacting our Technical Assistance Department. 62 STATUS INDICATORS 63 MISFEED REMOVAL 1 order. 2 A: Misfeed in the paper feed area 1 2 B: Misfeed in the fusing area 1 2 3 C: Misfeed in the transport area 1 2 3 4 D: Misfeed in the lower paper feed area (AL-1551CS) 1 2 3 E: Misfeed in the SPF/RSPF (AL-1551CS) Roller rotating knob Reversing tray 9 68 SPECIFICATIONS Page 70 ABOUT SUPPLIES AND OPTIONS Supply list Interface cable Parallel interface cable 1 2 3 4 5 6 7 72 INDEX A B C M N O P R U Z INDEX BY PURPOSE SOFTWARE LICENSE 2. Restrictions. 3. Termination. 4. Export Law Assurances. 5. Government End Users. 6. Limited Warranty on Media. 7. Disclaimer of Warranty on Software. 8. Limitation of Liability. 9. Controlling Law and Severability. 10. Complete Agreement. 1. PRODUCT AND COMPANY IDENTIFICATION 2. COMPOSITION/INFORMATION ON INGREDIENTS 3. HAZARDS IDENTIFICATION 4. FIRST-AID MEASURES 5. FIRE -FIGHTING MEASURES 6. ACCIDENTAL RELEASE MEASURES 7. HANDLING AND STOR AGE 8. EXPOSURE CONTROL / PERSONA L PROTECTION 9. PHYSICAL AND CHEMICAL PROPERTIES 10. STABILITY AND REACTIVITY 11. TOXICOLOGICAL INFORMATION 12. ECOLOGICAL INFORMATION 13. DISPOSAL CONSIDERATION 14. TRANSPORT INFORMATION 15. REGULATORY INFORMATION 16. OTHER INFORMATION 1. PRODUCT AND COMPANY IDENTIFICATION 2. COMPOSITION/INFORMATION ON INGREDIENTS 3. HAZARDS IDENTIFICATION 4. FIRST-AID MEASURES 5. FIRE -FIGHTING MEASURES 6. ACCIDENTAL RELEASE MEASURES 7. HANDLING AND STOR AGE 9. PHYSICAL AND CHEMICAL PROPERTIES 10. STABILITY AND REACTIVITY 11. TOXICOLOGICAL INFORMATION 12. ECOLOGICAL INFORMATION 13. DISPOSAL CONSIDERATION 14. TRANSPORT INFORMATION 15. REGULATORY INFORMATION 16. OTHER INFORMATION