Replacing the Air Filter, Remove the air filter | Sharp PG-C45X

Replacing the Air Filter

•This projector is equipped with air fil- ters to ensure the optimal operating condition of the projector.

•The air filters should be cleaned ev- ery 100 hours of use. Clean the filters more often when the projector is used in a dusty or smoky location.

•Ask your nearest Sharp Authorized Projector Dealer or Service Center to exchange the filter (PFILDA005WJZZ) when it is no longer possible to clean.

M4

M4

M4

M4

Air filter Air filter (not removable)

Power (OFF) button

Cleaning and replacing the bottom air filter

1 Turn off the power and discon- nect the power cord.

•Press . Wait until the cooling fan

stops.

Power (OFF) button

2

3

Remove the bottom filter cover.

•Turn over the projector. Grab the tab

and slide open the filter cover in the direction of the arrow.

	Remove the air filter.	Tab
	• Pick the air filter up with your fingers	Tab
	• Pick the air filter up with your fingers
	and lift it out of the filter cover.

Appendix

-81

Image 85

Sharp PG-C45X Replacing the Air Filter, Cleaning and replacing the bottom air filter, Remove the bottom filter cover

Contents

PG-C45X Model No. PG-C45X Serial No Special Note for Users in the U.K Page Introduction Product Disposal Color Management System Outstanding FeaturesNoise Reduction New Edge Up-Scaling Contents Appendix Accessories CleaningPower Sources Power-Cord Protection Replacement Parts Damage Requiring ServiceSafety Check Wall or Ceiling Mounting Using the projector in other countries Avoid locations with high or low temperatureTemperature monitor function Rest your eyes occasionally For other operating systems For other languages To install Acrobat Reader from the CD-ROMFor Windows For Macintosh Projector Front and Top View Part Names Projector Rear View Using the Kensington Lock Remote Control Top View Remote Control Front ViewPart Names Available Range of the Remote Control Using the Remote ControlWhen using the remote control Inserting the Batteries Supplied accessories AccessoriesOptional cables Connections and Setup Before Connecting Connecting the Projector to Other DevicesThis projector can be connected to An audio cable commercially available See Connecting the Power Cord Ferrite core Connecting to a Computer Using the RGB Cable Plug and Play function when connecting to a 15-pin terminal Connecting to Video Equipment Cable Connecting to Component Video Equipment Connecting to an Amplifier or Other Audio Components Connecting to an Amplifier Controlling the Projector by a Computer Watching Images on Both the Projector and a Monitor Connecting to a Monitor Press or while using presentation software on your computer Using the Wireless Pre- sentation FunctionButton Connecting the Remote Control to the Projector Using as a Wired Remote Control Using the Adjustment Feet Setup Focus ring Zoom knob Adjusting the LensOut Zoom Throw Distance Setting up the Screen Stretch Mode Normal ModeScreen Size and Projection Distance AN-C12MZ Throw ratio 11.18 to Projection from behind the screen Projecting a Reversed/Inverted Image Basic Operation Plug the power cord into the wall outlet Basic ProcedurePress on the projector or on the remote control Image Projection Volume buttons Press , , or on the remote control to select the Input mode Press to temporarily turn off the sound Selecting the On-screen Display LanguagePress Press \ or to select Lan Press or to select the de- sired language, and then press Correcting Trapezoidal Distortion Press , , \ and to adjust the Keystone correctionKeystone button Enter button Undo button Buttons Test pattern Undo button Sub menu Menu Bar Items Main menu Sub menu Input 3 / 4 Mode Menu Selections Adjustments Using the Menu ScreenMenu Bar Main Menu Enter button Buttons Menu button Press or to select the item you want to adjust Press \ or to select the menu you want to adjustPress \ or to adjust the item selected Press or to select the item you want to set Menu Selections SettingsEnter button Buttons Menu button Cursor shifts to the sub menu Adjusting Image Preferences Adjusting the PictureSelecting the Signal Type Progressive Mode When Auto Sync is OFF Adjusting Computer ImagesSaving Adjustment Settings Special Mode Settings Selecting Adjustment SettingsChecking the Input Signal Auto Sync Display Function Auto Sync AdjustmentScreen display during Auto Sync Auto Sync button Easy to Use Functions Switching the Picture Display Using Different Input Signals Selecting the Picture Display ModeResize button Screen display of the picture display mode Video Freezing a Moving Image Displaying a Still ImageFreeze button Displaying an Enlarged Portion of an Image Enlarging a Specific Portion of an ImageButtons Enlarge Enlarge/ Reduce buttons Gamma Correction Function Adjusting Gamma Correction Displaying the Inset Picture Displaying Dual Pictures Pict in PictPress to move the inset pic- ture Blacking out the Pro- jected Image Black Screen FunctionTo return to the original projected image, press again This function can be used to display a black screen Displaying and Setting the Break Timer Displaying the Break TimerPress to cancel the break timer Buttons Break Timer button Selecting the Target Color Selecting the Color Reproduction Mode Setting the Chromatic Value of the Target Color Setting the Brightness of the Target ColorSetting the Hue of the Target Color Overview of All Color Settings Resetting User-Defined Color Settings Setting on/off the Internal Speaker Setting the Audio Output TypeSetting the Audio Out- put Type Setting on/off the Inter- nal Speaker Auto Search Function Using Auto Search Video Digital Noise Reduction DNR System Setting On-screen DisplayReducing Image Noise Turning Off On-screen Display Setting the Video System Setting the Video System Capturing the Image Saving Projected ImagesDeleting the Captured Image Selecting a Startup Image Setting a Background ImageSelecting a Background Image Selecting a Startup Image Setting the Power Save Mode Selecting the Economy ModeMonitor Out/RS-232C Off Function Selecting the Economy Mode Automatic Power Off FunctionDisplaying the Remaining Lamp Life Percentage Checking the Remaining Lamp Life Percentage Setting up the Keylock Setting the Projection ModeReversing/Inverting Projected Images Locking the Operation Buttons on the Projector Selecting the Transmission Speed RS-232C Canceling the Keylock SettingSelecting the Transmis- sion Speed RS-232C Entering the Password Setting up a Password If You Forget Your Password Changing the Password Entering the Keycode Setting the Anti-Theft Enter the same 4-digit keycode in Reconfirm Changing the Keycode Returning to Default Settings Initializing the Settings Overview of All Menu Settings Displaying the Adjustment Settings Appendix Cleaning the projector MaintenanceCleaning the lens Cleaning the exhaust and intake vents Turn off the power and discon- nect the power cord Cleaning and replacing the bottom air filterReplacing the Air Filter Remove the bottom filter cover Replace the air filter Clean the air filterReplace the filter cover About the temperature warning indicator Maintenance IndicatorsAbout the lamp replacement indicator Maintenance Indicators Lamp Regarding the LampReplacing the Lamp Press on the projector to turn off the power Removing and Install- ing the Lamp UnitDisconnect the power cord Change the air filter Resetting the Lamp Timer RGB Input Component Input Connecting Pin Assignments Commands RS-232C Specifications and Command SettingsPC control Communication conditions RS-232C Specifications and Command Settings Options Control Contents Specifications of wired remote control input Wired Remote Control Terminal SpecificationsSharp remote control signal format Function and transmisson codes Computer Computer Compatibility Chart Troubleshooting Troubleshooting For Sharp Assistance Ntsc 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM Specifications Units inches mm Dimensions Advanced intelligent compression Glossary 100 Index 101 Stretch Sharp Corporation