(RS-232C) Specifications and Command Settings
PC control
A computer can be used to control the projector by connecting an
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to
Baud rate: 9,600 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer.
Command format
| C1 C2 | C3 | C4 | P1 | P2 | P3 | P4 |
|
|
|
|
| Return code (0DH) |
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Command | Parameter |
|
|
|
| ||||||||||||
Response code format |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Normal response |
| Problem response (communication error or incorrect command) | ||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
| O | K |
|
| Return code (0DH) |
|
|
| E | R | R |
| Return code (0DH) |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Info
•When more than one code is being sent, send each command only after the response code for the previous command from the projector is verified.
•In the case of transmitting commands during standby, it takes a maximum of 30 seconds until the response code is received.
•When the power is turned on during standby with the “POWER ON” command, wait for at least 30 seconds after the power has been turned on, and then transmit the next command.
Note
•When using the computer control function of the projector, the projector’s operating status cannot be read by the computer. Therefore, confirm the status by transmitting the display commands for each adjustment menu and checking the status with the
Commands
Example:
•When “BRIGHT” of INPUT 1 image adjustment is set to –10.
|
|
| Computer | → | Projector | |||||||
|
|
|
|
|
|
|
|
|
|
|
| |
R | A | B | R | _ | – | 1 | 0 |
| O | K |
| |
| ← |
| ||||||||||
BUTTONS & REMOTE CONTROL KEY
CONTROL CONTENTS
POWER ON
POWER OFF
VOLUME (0 - 60)
MUTE ON
MUTE OFF
KEYSTONE
DIGITAL SHIFT
COMMAND | PARAMETER | RETURN | ||||||
P | O | W | R | _ | _ | _ | 1 | OK OR ERR |
P | O | W | R | _ | _ | _ | 0 | OK OR ERR |
V | O | L | A | _ | _ | * | * | OK OR ERR |
M | U | T | E | _ | _ | _ | 1 | OK OR ERR |
M | U | T | E | _ | _ | _ | 0 | OK OR ERR |
K | E | Y | S | * | * | * | * | OK OR ERR |
L | N | D | S | _ | * | * | * | OK OR ERR |
|
|
|
|
|
|
|
|
|
BUTTONS & REMOTE CONTROL KEY
CONTROL CONTENTS
BLACK SCREEN ON
BLACK SCREEN OFF
INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT CHECK
FREEZE ON
FREEZE OFF
AUTO SYNC START
COMMAND | PARAMETER | RETURN | ||||||
I | M | B | K | _ | _ | _ | 1 | OK OR ERR |
I | M | B | K | _ | _ | _ | 0 | OK OR ERR |
I | R | G | B | _ | _ | _ | 1 | OK OR ERR |
I | R | G | B | _ | _ | _ | 2 | OK OR ERR |
I | V | E | D | _ | _ | _ | 1 | OK OR ERR |
I | V | E | D | _ | _ | _ | 2 | OK OR ERR |
I | C | H | K | _ | _ | _ | 0 | OK OR ERR |
F | R | E | Z | _ | _ | _ | 1 | OK OR ERR |
F | R | E | Z | _ | _ | _ | 0 | OK OR ERR |
A | D | J | S | _ | _ | _ | 1 | OK OR ERR |
|
|
|
|
|
|
|
|
|
Appendix
-89
