TOP VIEW
REMOTE CONTROL
SIGNAL TRANSMITTER
WIRED REMOTE CONTROL INPUT 
(3.5mm Mono Minijack)
|
|
| LASER LIGHT WINDOW | ||||
|
|
| Laser light shines out of | ||||
|
|
| this window. | ||||
|
|
|
|
|
|
| |
| CAUTION |
| "COMPLIES WITH 21 CFR SUBCHAPTER J" |
| |||
|
| SHARP PLAZA, MAHWAH, NEW JERSEY 07430 |
| ||||
|
|
| SHARP ELECTRONICS CORPORATION |
| |||
|
|
| TEL : |
|
|
|
|
| LASER RADIATION- |
|
| U.S.A. ONLY |
|
| |
|
|
|
|
| |||
| DO NOT STARE INTO BEAM |
| REMOTE CONTROL |
|
|
|
|
|
|
|
|
|
| ||
| WAVE LENGTH : 670nm |
| MODEL NO. : RRMCG1327CESA |
|
|
|
|
|
| DC6V (1.5VX4PCS.) |
|
|
|
| |
| MAX. OUTPUT : 1mW |
| MADE IN JAPAN |
|
|
|
|
| CLASS II LASER PRODUCT |
| FABRIQUÉ AU JAPON |
|
|
|
|
|
|
|
|
|
|
|
|
Using the optional cable with the remote control
•When the remote control cannot be used due to the range or positioning of the projector (rear projection, etc.), connect the optional cable from the Wired Remote Control Jack of the remote control to the Wired Remote Input on the back of the projector.
Note:
•The signal transmitter does not function when the optional cable is connected to the remote control.
The laser pointer on the remote control emits a laser beam from the laser light window shown in the figure above. The laser emitted is a class II laser; therefore, do not look into the laser window or shine the laser beam on yourself or other people. The two marks to the left are the caution labels for the laser beam.
Always use the laser pointer at temperatures between 41°F to 104°F (5°C to 40°C).
REAR VIEW
Press in and |
|
|
|
|
|
|
|
|
|
|
| Insert the side | ||
downward on |
|
|
|
|
|
|
|
|
|
|
|
|
| tabs into their |
|
|
|
|
|
| |||||||||
the arrow |
|
|
|
|
|
|
|
|
|
|
|
|
| slots and press |
mark and |
|
|
|
|
|
|
|
|
|
|
| in the cover | ||
remove. |
|
|
|
|
|
|
|
|
|
|
| until properly | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| seated. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Inserting the Batteries
Remove the battery cover as shown and insert four AA size batteries making sure their polarities match the (+) and
Notes:
Incorrect use of batteries may cause them to leak or burst.
•Insert the batteries with the (+) and
•Remove the batteries if the remote control will not be operated for an extended period of time.
•Maintain the batteries in a clean condition.
•Do not mix different brands of batteries. The life expectancy of the new batteries will be shortened and the old batteries may leak.
•When the batteries have been used up, remove them immediately to prevent leakage and damage. Leaked battery fluid may irritate the skin. Remove any battery fluid by wiping with a cloth.
•Due to storage conditions and the shelf life of the supplied batteries, they may run out after a short time. If so, replace them with new batteries as soon as possible.
Transmission range | Reception range |
30° | 30° |
Max. distance: 23' (7 m)
30° 45°
Remote control positioning
Use the remote control as shown in the figures on the left.
Note:
•The signal from the remote control can be reflected off the screen for easy operation. However, the effective distance of the signal may differ due to the screen material.
