Setting up the Projector Network Environment | Sharp XG-C435X

Setting up the Projector Network Environment

This section describes the basic procedure for using the projector via the network.

If the network is already constructed, the projector’s network settings may need to be changed. Please consult your network administrator for assistance with these settings.

You can make network settings both on the projector and on the computer. The following procedure is for making settings on the computer.

Network settings on the computer

1. Connecting the projector to a computer

Connect a LAN cable (Category 5, cross-over type) between the computer and projector.

LAN cable

(commercially available)

Page 19

2. Setting an IP address for the computer

Adjust the IP settings of the computer to enable one-to-one communications with the projector.

Temporarily change the computer’s IP address.

Pages 20, 21

3. Setting up a network connection for the projector

Adjust the projector network settings to conform to your network.

Use Internet Explorer (version 5.0 or later) to make various projector settings.

Pages 22, 23

•Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or other countries.

•All other company or product names are trademarks or registered trademarks of their respective compa- nies.

-18

Image 18

Sharp XG-C435X, XG-C465X specifications Setting up the Projector Network Environment, Network settings on the computer

Contents

Setup Manual Setting up the Screen Standard Setup Front Projection Screen Screen Size and Projection DistanceThrow Distance 12.2 15.2m 50ft Standard Zoom Lens Normal ModeStretch Mode F1.7-F1.9, f=28.0-33.6 mm Wide-zoom Lens AN-C12MZ F2.2-F2.7, f=24.5-30.7 mm Tele-zoom Lens AN-C18MZ F1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C27MZ F2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C41MZ F2.1-F2.8, f=83.5-117.2 mm Changing the Lens Info Replace the lens housing cover Insert the lens into the projector Connecting Pin Assignments COMPUTER-RGB Input/Output Component Input/Output Connecting Pin Assignments Pin No. Signal RS-232C Specifications and Commands Computer control Communication conditionsBasic format Commands W R Return DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Setting up the Projector Network Environment Network settings on the computer Connecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Controlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Status Status Confirming the ProjectorControlling the Projector Control Projector Settings & Adjustments Setting and AdjustingSetting the Security Network Security Mail Originator Settings Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs General Mail Recipient Settings Occurs Service & Support Access URLExample of the display when an error occurs Input setup and press the Enter key Setting up the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Launch general purpose terminal emulator When Connecting Using Telnet ClickStartfrom theWindows desk- top and select Run Setup Menu Main Menu View Setting Detail List VView All SettingSet Items SSave & Quit Save Settings and QuitQuit without Saving Set Tings QQuit Unchanged Subnet Mask Setting IP Address SettingDefault Gateway Setting User Name Setting Dhcp Client Setting Password SettingProjector Name Setting RS-232C Baud Rate Set Entering Advanced Setup Menu Disconnecting All ConnecSetting Auto Logout Time Data Port Setting Setting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses Setting of Search Port Return to Default SettingsReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Resetting the Lamp Timer of the Projector via LAN Close HyperTerminal Troubleshooting When connecting the projector using serial-connection Troubleshooting \ After the initialization, carry out setting again Dimensions Units inches mm When AN-C27MZ is installed When AN-C12MZ is installedWhen AN-C18MZ is installed When AN-C41MZ is installed