Sharp XG-C435X, XG-C465X Connecting Pin Assignments

-11

RS-232C Terminal:9-pin mini DIN female connector

Pin No. Signal Name I/O Reference

1Not connected

2RDReceive Data Input Connected to internal circuit

3SDSend Data Output Connected to internal circuit

4Not connected

5SGSignal Ground Connected to internal circuit

6Not connected

7RSRequest to Send Connected to CS in internal circuit

8CSClear to Send Connected to RS in internal circuit

9Not connected

RS-232C Terminal: 9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor

Pin No. Signal Name I/O Reference

1Not connected

2RDReceive Data Input Connected to internal circuit

3SDSend Data Output Connected to internal circuit

4Not connected

5SGSignal Ground Connected to internal circuit

6Not connected

7RSRequest to Send Connected to CS in internal circuit

8CSClear to Send Connected to RS in internal circuit

9Not connected

RS-232C Cable recommended connection: 9-pin D-sub female connector

Pin No. Signal Pin No. Signal

1CD 1 CD

2RD 2 RD

3SD 3 SD

4ER 4 ER

5SG 5 SG

6DR 6 DR

7RS 7 RS

8CS 8 CS

9CI 9 CI

Note

•Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling

device (e.g. computer).

LAN Terminal : 8-pin RJ-45 modular connector

Pin No. Signal Pin No. Signal

1TX+ 5

2TX– 6 RX–

3RX+ 7

48

8

9

6

5

12

4

3

7

1

6

11

5

15

10

COMPUTER-RGB/COMPONENT INPUT 1, 2 and COMPUTER-RGB/COMPONENT OUTPUT Terminals

:

15-pin mini D-sub female connector

Connecting Pin Assignments

COMPUTER-RGB Input/Output

1. Video input (red)

2. Video input (green/sync on green)

3. Video input (blue)

4. Not connected

5. Not connected

6. Earth (red)

7. Earth (green/sync on green)

8. Earth (blue)

9. Not connected

10. GND

11. Not connected

12. Bi-directional data

13. Horizontal sync signal: TTL level

14. Vertical sync signal: TTL level

15. Data clock

Component Input/Output

1. PR (CR)

2. Y

3. PB (CB)

4. Not connected

5. Not connected

6. Earth (PR)

7. Earth (Y)

8. Earth (PB)

9. Not connected

10. Not connected

11. Not connected

12. Not connected

13. Not connected

14. Not connected

15. Not connected

15

69

51

96

8...1

Projector

Pin No.

4

5

6

Computer

Pin No.

4

5

6

Contents

Main MODEL XG-C465X XG-C435X Setting up the Projector Using RS-232C or Telnet .... Setting up the Projector Network Environment ... DATA PROJECTOR SETUP MANUAL Setting up the Screen Screen Size and Projection Distance Throw Distance 3.0 6.0 9.1 15.212.2 (m) 10 20 30 5040 (ft) The graph below is for 100 inches (254 cm) screen with 4:3 normal mode. Standard Zoom Lens F1.7-F1.9, f=28.0-33.6 mm NORMAL Mode (4:3) Wide-zoom Lens (AN-C12MZ) F2.2-F2.7, f=24.5-30.7 mm Tele-zoom Lens (AN-C18MZ) F1.7-F2.2, f=36.5-46.3 mm STRETCH Mode (16:9) Tele-zoom Lens (AN-C27MZ) F2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens (AN-C41MZ) F2.1-F2.8, f=83.5-117.2 mm Changing the Lens 1 2 3 4 5 6 7 Changing the Lens RS-232C Terminal:9-pin mini DIN female connector Connecting Pin Assignments COMPUTER-RGB Input/Output Component Input/Output 51 96 Connecting Pin Assignments Pin No. Signal DVI-D Input Terminal Pin No. Signal Computer control RS-232C Specifications and Commands Commands Example: When turning on the projector, make the following setting. POWR _1__ OK ProjectorComputer Page Page *5 Lamp Timer Reset command is available only in standby mode. 1. Page 19 Pages 22, 23 Pages 20, 21 Setting up the Projector Network Environment 1 2 3 4 2. Setting an IP Address for the Computer 1 2 3 4 5 6 7 3. Setting up a Network Connection for the Projector 1 2 3 4 pears, ready for network settings for the projector. 5 6 that the values are set properly, and then click the Confirm but- ton. Controlling the Projector via LAN Controlling the Projector Using Internet Explorer 1 2 3 Confirming the Projector Status Controlling the Projector (Control) Setting and Adjusting the Projector (Settings & Adjustments) Setting the Security (Network Security) Making General Settings for the Network General) Setting for Sending E-mail when an Error Occurs (Mail Originator Settings) Setting Error Items and Destination Addresses to which E-mail is to be Sent when an Error Occurs (Mail Recipient Settings) Setting Error Items and the URL that are to be Displayed when an Error Occurs Access URL) Setting up the Projector Using RS-232C or Telnet When Connecting Using RS-232C 1 2 3 1 2 3 4 5 6 SETUP MENU ADVANCED SETUP MENU View Setting Detail List ([V]View All Setting) Set Items Setting up the Projector Using RS-232C or Telnet Save Settings and Quit ([S]Save & Quit) Quit without Saving Set- tings IP Address Setting ([1]IP Address) Subnet Mask Setting ([2]Subnet Mask) Default Gateway Setting Password Setting ([5]Password) RS-232C Baud Rate Set- ting Projector Name Setting ([7]Projector Name) Disconnecting All Connec- tions Entering ADVANCED SETUP MENU ([A]Advanced Setup) Setting Auto Logout Time (ADVANCED[1]Auto Logout Time) Carrying out Network Ping Test (ADVANCED[5]Network Ping Test) Setting of Accept IP Ad- dress Addr(1) - [8]Accept IP Addr(3)) Accepting All IP Addresses Setting of Search Port (ADVANCED[0]Search Port) Return to Default Settings (ADVANCED[!]Restore Default Setting) Return to Main Menu 1 2 3 4 Resetting the Lamp Timer of the Projector via LAN Page Troubleshooting Communication cannot be established with the projector When connecting the projector using serial-connection When connecting the projector to a computer using network (LAN)- connection Check the network settings for the computer and the projector Troubleshooting A connection cannot be made because you have forgotten your user name or your password. Troubleshooting Dimensions Units: inches (mm) Dimensions Projector and Lens Dimensions [When AN-C12MZ is installed] [When AN-C18MZ is installed] [When AN-C27MZ is installed] [When AN-C41MZ is installed]