Sharp XG-C465X, XG-C435X instruction

Setting up the Projector Network Environment

5 Click “Internet Protocol (TCP/IP)”, and click the “Properties” button.

1

2

6 Confirm or change an IP address for the setup computer.

1Confirm and note the current IP ad- dress, Subnet mask and Default gateway.

Make sure to note the current IP ad- dress, Subnet mask and Default gate- way as you will be required to reset

them later.

2Set temporarily as follows :

IP address : 192.168.150.3

Subnet mask : 255.255.255.0

Default gateway : (Do not input any values.)

Note

•The factory default settings for the projector are as follows:

DHCP Client : Off

IP address : 192.168.150.2

Subnet mask : 255.255.255.0

Default gateway : 0.0.0.0

7

After setting, click the “OK” but- ton, and then restart the com- puter.

After confirming or setting, proceed to “3. Setting up Network Connection for the Pro-

jector”.

-21

Image 21

Sharp XG-C465X, XG-C435X specifications Confirm or change an IP address for the setup computer

Contents

Setup Manual Standard Setup Front Projection Setting up the Screen Throw Distance Screen Size and Projection DistanceScreen 12.2 15.2m 50ft Stretch Mode Normal ModeStandard Zoom Lens F1.7-F1.9, f=28.0-33.6 mm F2.2-F2.7, f=24.5-30.7 mm Wide-zoom Lens AN-C12MZ F1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C18MZ F2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C27MZ F2.1-F2.8, f=83.5-117.2 mm Tele-zoom Lens AN-C41MZ Info Changing the Lens Insert the lens into the projector Replace the lens housing cover COMPUTER-RGB Input/Output Component Input/Output Connecting Pin Assignments Pin No. Signal Connecting Pin Assignments RS-232C Specifications and Commands Computer control Communication conditionsBasic format W R Commands Return DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Network settings on the computer Setting up the Projector Network Environment Connecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Controlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Controlling the Projector Confirming the ProjectorStatus Status Control Setting the Security Setting and AdjustingProjector Settings & Adjustments Network Security Setting for Sending E-mail when an Error Occurs Making General Settings for the Network NetworkMail Originator Settings General Mail Recipient Settings Occurs Service & Support Access URLExample of the display when an error occurs When Connecting Using RS-232C Setting up the Projector Using RS-232C or TelnetInput setup and press the Enter key Launch general purpose terminal emulator ClickStartfrom theWindows desk- top and select Run When Connecting Using Telnet Setup Menu Main Menu View Setting Detail List VView All SettingSet Items Quit without Saving Set Save Settings and QuitSSave & Quit Tings QQuit Unchanged Default Gateway Setting IP Address SettingSubnet Mask Setting User Name Setting Projector Name Setting Password SettingDhcp Client Setting RS-232C Baud Rate Set Setting Auto Logout Time Disconnecting All ConnecEntering Advanced Setup Menu Data Port Setting Setting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses Setting of Search Port Return to Default SettingsReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Close HyperTerminal Resetting the Lamp Timer of the Projector via LAN When connecting the projector using serial-connection Troubleshooting Troubleshooting \ After the initialization, carry out setting again Units inches mm Dimensions When AN-C18MZ is installed When AN-C12MZ is installedWhen AN-C27MZ is installed When AN-C41MZ is installed