Sharp XG-C435X, XG-C465X 1, 2, 3, 4

-19

Setting up the Projector Network Environment

1. Connecting the Pro-

jector to a Computer

Establishing a one-to-one connection from the

projector to a computer. Using a LAN cable

(Category 5, cross-over type) you can config-

ure the projector via the computer.

1Disconnect the computer’s LAN

cable from the existing network.

2Connect a LAN cable (a UTP

cable, Category 5, cross-over

type) to the projector’s LAN ter-

minal and connect the other end

of the cable to the computer’s

LAN terminal.

3Plug the power cord into the AC

socket of the projector.

4Turn on the computer.

Info

Confirm that the LINK LED on the rear of the

projector illuminates. If the LINK LED does not

illuminate, check the following :

•The LAN cable is properly connected.

•The power switches of both the projector

and the computer are on.

LAN cable

(cross-over type, commercially available)

ON

A LAN cable being

connected to the network

This completes the connection. Now proceed to “2. Setting an IP Address for the Com-

puter”.

Contents

Main MODEL XG-C465X XG-C435X Setting up the Projector Using RS-232C or Telnet .... Setting up the Projector Network Environment ... DATA PROJECTOR SETUP MANUAL Setting up the Screen Screen Size and Projection Distance Throw Distance 3.0 6.0 9.1 15.212.2 (m) 10 20 30 5040 (ft) The graph below is for 100 inches (254 cm) screen with 4:3 normal mode. Standard Zoom Lens F1.7-F1.9, f=28.0-33.6 mm NORMAL Mode (4:3) Wide-zoom Lens (AN-C12MZ) F2.2-F2.7, f=24.5-30.7 mm Tele-zoom Lens (AN-C18MZ) F1.7-F2.2, f=36.5-46.3 mm STRETCH Mode (16:9) Tele-zoom Lens (AN-C27MZ) F2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens (AN-C41MZ) F2.1-F2.8, f=83.5-117.2 mm Changing the Lens 1 2 3 4 5 6 7 Changing the Lens RS-232C Terminal:9-pin mini DIN female connector Connecting Pin Assignments COMPUTER-RGB Input/Output Component Input/Output 51 96 Connecting Pin Assignments Pin No. Signal DVI-D Input Terminal Pin No. Signal Computer control RS-232C Specifications and Commands Commands Example: When turning on the projector, make the following setting. POWR _1__ OK ProjectorComputer Page Page *5 Lamp Timer Reset command is available only in standby mode. 1. Page 19 Pages 22, 23 Pages 20, 21 Setting up the Projector Network Environment 1 2 3 4 2. Setting an IP Address for the Computer 1 2 3 4 5 6 7 3. Setting up a Network Connection for the Projector 1 2 3 4 pears, ready for network settings for the projector. 5 6 that the values are set properly, and then click the Confirm but- ton. Controlling the Projector via LAN Controlling the Projector Using Internet Explorer 1 2 3 Confirming the Projector Status Controlling the Projector (Control) Setting and Adjusting the Projector (Settings & Adjustments) Setting the Security (Network Security) Making General Settings for the Network General) Setting for Sending E-mail when an Error Occurs (Mail Originator Settings) Setting Error Items and Destination Addresses to which E-mail is to be Sent when an Error Occurs (Mail Recipient Settings) Setting Error Items and the URL that are to be Displayed when an Error Occurs Access URL) Setting up the Projector Using RS-232C or Telnet When Connecting Using RS-232C 1 2 3 1 2 3 4 5 6 SETUP MENU ADVANCED SETUP MENU View Setting Detail List ([V]View All Setting) Set Items Setting up the Projector Using RS-232C or Telnet Save Settings and Quit ([S]Save & Quit) Quit without Saving Set- tings IP Address Setting ([1]IP Address) Subnet Mask Setting ([2]Subnet Mask) Default Gateway Setting Password Setting ([5]Password) RS-232C Baud Rate Set- ting Projector Name Setting ([7]Projector Name) Disconnecting All Connec- tions Entering ADVANCED SETUP MENU ([A]Advanced Setup) Setting Auto Logout Time (ADVANCED[1]Auto Logout Time) Carrying out Network Ping Test (ADVANCED[5]Network Ping Test) Setting of Accept IP Ad- dress Addr(1) - [8]Accept IP Addr(3)) Accepting All IP Addresses Setting of Search Port (ADVANCED[0]Search Port) Return to Default Settings (ADVANCED[!]Restore Default Setting) Return to Main Menu 1 2 3 4 Resetting the Lamp Timer of the Projector via LAN Page Troubleshooting Communication cannot be established with the projector When connecting the projector using serial-connection When connecting the projector to a computer using network (LAN)- connection Check the network settings for the computer and the projector Troubleshooting A connection cannot be made because you have forgotten your user name or your password. Troubleshooting Dimensions Units: inches (mm) Dimensions Projector and Lens Dimensions [When AN-C12MZ is installed] [When AN-C18MZ is installed] [When AN-C27MZ is installed] [When AN-C41MZ is installed]