Connecting Pin Assignments, Pin No. Signal | Sharp XG-C435X specification

Connecting Pin Assignments

DVI-D Input Terminal

24						17

8	1
16	9

Pin No. Signal

1T.M.D.S. Data 2–

2T.M.D.S. Data 2+

3T.M.D.S. Data 2 Shield

4Not connected

5Not connected

6DDC Clock

7DDC Data

8Not connected

9T.M.D.S. Data 1–

10T.M.D.S. Data 1+

11T.M.D.S. Data 1 Shield

12Not connected

Pin No. Signal

13Not connected

14+5 V Power

15Ground

16Hot Plug Detect

17T.M.D.S. Data 0–

18T.M.D.S. Data 0+

19T.M.D.S. Data 0 Shield

20Not connected

21Not connected

22T.M.D.S. Clock Shield

23T.M.D.S. Clock+

24T.M.D.S. Clock–

-12

Image 12

Sharp XG-C435X, XG-C465X specifications Connecting Pin Assignments, Pin No. Signal

Contents

Setup Manual Setting up the Screen Standard Setup Front Projection Screen Size and Projection Distance Throw DistanceScreen 12.2 15.2m 50ft Normal Mode Stretch ModeStandard Zoom Lens F1.7-F1.9, f=28.0-33.6 mm Wide-zoom Lens AN-C12MZ F2.2-F2.7, f=24.5-30.7 mm Tele-zoom Lens AN-C18MZ F1.7-F2.2, f=36.5-46.3 mm Tele-zoom Lens AN-C27MZ F2.0-F2.8, f=53.8-82.9 mm Tele-zoom Lens AN-C41MZ F2.1-F2.8, f=83.5-117.2 mm Changing the Lens Info Replace the lens housing cover Insert the lens into the projector Connecting Pin Assignments COMPUTER-RGB Input/Output Component Input/Output Connecting Pin Assignments Pin No. Signal RS-232C Specifications and Commands Computer control Communication conditionsBasic format Commands W R Return DVI Signal Type D. PC Comp OK or ERR Lamp Timer Reset command is available only in standby mode Setting up the Projector Network Environment Network settings on the computer Connecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector Dhcp Controlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Confirming the Projector Controlling the ProjectorStatus Status Control Setting and Adjusting Setting the SecurityProjector Settings & Adjustments Network Security Making General Settings for the Network Network Setting for Sending E-mail when an Error OccursMail Originator Settings General Mail Recipient Settings Occurs Service & Support Access URLExample of the display when an error occurs Setting up the Projector Using RS-232C or Telnet When Connecting Using RS-232CInput setup and press the Enter key Launch general purpose terminal emulator When Connecting Using Telnet ClickStartfrom theWindows desk- top and select Run Setup Menu Main Menu View Setting Detail List VView All SettingSet Items Save Settings and Quit Quit without Saving SetSSave & Quit Tings QQuit Unchanged IP Address Setting Default Gateway SettingSubnet Mask Setting User Name Setting Password Setting Projector Name SettingDhcp Client Setting RS-232C Baud Rate Set Disconnecting All Connec Setting Auto Logout TimeEntering Advanced Setup Menu Data Port Setting Setting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses Setting of Search Port Return to Default SettingsReturn to Main Menu Resetting the Lamp Timer of the Projector via LAN Resetting the Lamp Timer of the Projector via LAN Close HyperTerminal Troubleshooting When connecting the projector using serial-connection Troubleshooting \ After the initialization, carry out setting again Dimensions Units inches mm When AN-C12MZ is installed When AN-C18MZ is installedWhen AN-C27MZ is installed When AN-C41MZ is installed