Sharp XL-HF401PH operation manual General control, Setting the clock Remote control only

General control

■To turn the power on

Press the ON/STAND-BY button to turn the power on.

After use:

Press the ON/STAND-BY button to enter the power stand-by mode.

■Display brightness control

To dim the display brightness, press the DEMO/DIMMER button on the remote control.

Dimmer 1 (Display is dim).

Dimmer 2 (Display gets dimmer).

Dimmer Off (Display is bright).

■Volume auto fade-in

If you turn off and on the main unit with the volume set to 27 or higher, the volume starts at 16 and fades in to the last set level.

■Volume control

Turn the volume knob towards VOLUME +/– (on main unit) or press VOL +/– (on remote control) to increase or decrease the volume.

■Direct key power on function

When you press any of the following buttons, the unit turns on.

●iPod, CD, USB, AUDIO/LINE INPUT, TUNER, NETWORK on the remote control: Selected function is activated.

●/ button on the main unit: The unit turns on and playback of the last func- tion will start (CD, TUNER, USB, iPod, AUDIO IN, LINE IN, NETWORK)

■Auto power on

During stand-by mode, when you select XL-HF401PH speaker through AirPlay icon on your AirPlay device, the unit will automatically power on to Network function and stream the music from your AirPlay device.

This condition applies when:

●The AirPlay network has previously been set up between the unit and your AirPlay device.

●Set the Network Stand-by mode to ON. (refer page 9)

■AirPlay auto switch

During other function (CD, TUNER, USB, iPod, Audio In, Line In), when you select XL- HF401PH speaker through AirPlay icon on your AirPlay device, the unit will automatically switch to Network function and stream the music from your AirPlay device.

This condition applies when:

●The AirPlay network has previously been set up between the unit and your AirPlay device.

■Auto power off function

The main unit will enter the stand-by mode (when iPod, iPhone or iPad is not connected) after 15 minutes of inactivity during:

iPod:	Not docked.
Audio In: No detection of input signal.
CD:	In the stop mode or no disc.
USB:	In the stop mode or no media.

Note:

However, if iPod or iPhone is docked, the unit will begin charging. “Charge Mode” will be displayed.

■Muting

The volume is muted temporarily when pressing the (MUTE) button on the remote control. Press again to restore the volume.

■X-Bass control

When the power is first turned on, the unit will enter the extra bass mode which emphasises the bass frequencies, and “X-Bass On” will appear. To cancel the extra bass mode, press the X-BASS button on the remote control.

■Bass control

1Press the BASS/TREBLE

button to select “Bass”.

2 Within 5 seconds, press

the VOLUME (+ or –)	- 5 ↔ - 4........↔ + 4 ↔ + 5
button to adjust the bass.

■Treble control

1Press the BASS/TREBLE

button to select “Treble”.

2 Within 5 seconds, press

the VOLUME (+ or –)	- 5 ↔ - 4........↔ + 4 ↔ + 5
button to adjust the treble.

■Function

When the FUNCTION button on main unit is pressed, the current function will change to different mode. Press the FUNCTION button repeatedly to select desired function.

CD FM STEREO FM MONO

Network USB

Line In Audio In iPod

Note:

The backup function will protect the memorised function mode for a few hours should there be a power failure or the AC power lead becomes disconnected.

Setting the clock (Remote control only)

CD/USB

RDS

In this example, the clock is set for the 24-hour (0:00) display.

1Press the ON/STAND-BY button to turn the power on.

2Press the CLOCK/TIMER button.

3Within 10 seconds, press the ENTER button. To adjust the

day, press the or button and then press the ENTER button.

4Press the or button to select 24-hour or 12-hour display and then press the ENTER button.

The 24-hour display will appear.

(0:00 - 23:59)

The 12-hour display will appear.

(AM 12:00 - PM 11:59)

The 12-hour display will appear.

(AM 0:00 - PM 11:59)

E-6