When selecting the Speaker Crossover | Sherwood RD-7503 manual

RD-7503(A)2008.11.41:45PM페이지55

When selecting the SPEAKER CROSSOVER

•Set the crossover frequency according to the frequency characteristics of the speakers connected. (For details on the frequency characteristics, refer to the operating instructions of the speakers.)

•If the frequency range of your speaker is 100 Hz ~ 20 kHz, the crossover frequency should be set to 100 Hz (or slightly higher).

•The low frequencies below the crossover frequency are to output from subwoofer or the speakers which are set to "FULL RANGE" (when not using a subwoofer).

1. Press the CURSOR UP(▲)/DOWN(▼) buttons to select the SPEAKER CROSSOVER, then press the ENTER button.

2. Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired speaker.

�Note :

• You cannot select the subwoofer and the speakers set to "NO".

3. Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to set the crossover frequency as desired.

• You can adjust the crossover frequency within the range of 40 ~ 250 Hz.

• Select "FULL RANGE" when the selected speaker can fully reproduce the low frequencies below 40 Hz.

ENGLISH

4. Repeat the above steps 2 and 3 until the crossover frequencies are all set as desired.

55

Image 55

Sherwood RD-7503 manual When selecting the Speaker Crossover

Contents

RD-7503 Important Safety Instructions Read this Before Operating Your Unit Introduction120 Contents System Connections Connecting Antennas Connecting Video Components Copyright protection system Connecting Audio ComponentsComponent video input default settings *2 Hdmi High Definition Multimedia Interface connection *1 Connecting Digital INS and OUT Connecting External INSDigital input default settings Surround back speakers Connecting SpeakersFront Bi-Amp Connections Connecting Subwoofer PRE OUT Speaker placement Connecting DC Trigger OUT Connecting Room 2 Outs SiriusConnect Home Tuner Connecting for System ControlConnecting Sirius Connector only for North America AC Input Cord Remote Sensor Front Panel ControlsFluorescent Display Bluetooth in Connector Setup MIC JackFront AUX in Jack ENTER/SEARCH MODE, Select buttons Universal Remote ControlsPower on button UP/DOWN / buttons Numeric 0~9, +10 Input Selector buttons Function Table of the Numbered Buttons Loading Batteries Repeat the above steps 1 to 4 for each of your Components Entering a setup code Removing a punch-through function Using a punch-through functionRemoving all punch-through functions To change a macro program Programming a macro functionOperating a macro function To remove a macro program Listening to a Program Source OperationsBefore operation Listening with headphones When CD, F.AUX, Video 1~ 3 is selected as an input sourceMuting the sound Surround modes Room TheaterHall Stadium Dolby Truehd Enjoying Surround Sound To cancel the surround mode for stereo operation Adjusting each channel level with test toneEnter the test tone mode Cancel the test tone function Press the Channel Level button Adjusting the current channel levelAdjust the level of the selected channel as desired Repeat the above steps 2 and 3 to adjust each channel level Recalling the memorized channel levels Memorizing the adjusted channel levels Listening to Radio Broadcasts Auto tuningManual tuning Auto presetting Press the MEMORY/ENTER button Manual presettingTuning to preset stations Tuning Signing up for Sirius Satellite Radio Press the Tuning UP+/DOWN- buttons repeatedly to select SRTo sign up, access the website at Sirius Satellite Radio only for North America Category search Direct search→ DIR Srch → CAT Srch → OFF Preset search Presetting channels Parental lock When tuning in the previously locked channelsTune in the channel you want to lock or unlock Dubbing from video components onto Dubbing the audio and video signals separately onto VideoTo record audio signals Recording Digital Audio Recording with MD Recorder Displaying the operation status Operating the sleep timerAdjusting the brightness of the fluorescent display Other Functions Start play on the component related to the Room 2 source Press the Room 2 button to enter the Room 2 modeSet the selected mode as desired Room 2 Source Playback Select the desired menu using the Cursor UP/DOWN buttons OSD Menu SettingsTurn the menu screen on When selecting the SPEAKER/ROOMEQSETUP When selecting the CH Level Setup Press the Cursor UP/DOWN buttons to select the desired item Setting the System SetupWhen selecting the items other than OSD Position Adjust When selecting the AMP Assign When selecting the Hdmi Audio OUT When selecting the Subwoofer ModeWhen selecting the Tone Control When selecting the Momentary OSD When selecting the Cinema EQ When selecting the OSD Position Adjust When selecting the menu of page 2 or Setting the Input Setup When selecting the Audio Mode When selecting the Hdmi AssignWhen selecting the Video Assign When selecting the Audio Assign When selecting the HD Audio When selecting the Auto SurroundWhen selecting the AV Sync When selecting the DC Trigger Confirm your entry When selecting the NameTo resume its factory input source name When selecting the Parental Lock When selecting the Edit Lock Code When selecting the Auto Setup Setting the Speaker / Room EQ SetupPreparations RD-7503A2008.11.4145PM페이지52 When selecting the Speaker Configuration About the speaker distance When selecting the Speaker Distance When selecting the Speaker Crossover When selecting the Room EQ Setup Memory mode Setting the CH Level SetupRepeat the above steps 1 and 2 to adjust each channel level Reference When selecting the Night Mode Setting the Sound ParameterAuto When selecting the Center Width control When selecting the Dolby Plii MusicRepeat the above steps 2 and 3 to adjust other parameters When selecting the Panorama mode When selecting the Volume Setting the Multi Room SetupWhen selecting the Room When selecting the Input Problem Possible Cause Remedy Troubleshooting Guide Specifications Setup Code Table CCE RCASSS TMK MEI KLHSTS NSC ABC HTS SAT RD-7503