9. Alarm
Type of alarm | Description |
Abnormal high voltage | Notifies when overcurrent such as high voltage |
| leakage occurs. The |
| stopped, HV ALRM sets off and output the |
| signal for failure. |
Sensor failure | Notifies that the feed back sensor doesn’t work |
| properly. SNSR ALARM lights up, and the |
| signal for sensor failure is output. |
CPU failure | Notifies that CPU fails due to noise. All LEDs |
| Flashes, and the signal for CPU failure is |
| output. |
Electrode needle | Notifies when the maintenance of the electrode |
maintenance | needle is necessary. NDL CHECK ALARM |
| lights up, and the maintenance output signal is |
| output. |
How to reset
Turn off the power supply to solve the problem. Once it’s solved, apply the power supply again. Or turn on and off the
Turn off the power supply to solve the problem. Once it’s solved, apply the power supply again. Or turn on and off the
Turn off the power supply to solve the problem. Once it’s solved, apply the power supply again. Or turn on and off the
Turn off the power supply and clean the electrode needle. Then apply the power supply.
10.Timing chart
Timing chart with a normal operation
Charged condition of the work | 30V | |
|
| 0V |
|
| ON |
Power supply DC24V | Input | OFF |
|
| |
| ON (Opration) | |
Input | OFF | |
Completion signal for |
| ON (discharge) |
Output |
| |
static charge elimination | OFF | |
|
| |
|
| ON (Output) |
Sensor monitor output | Output | OFF |
Charged condition |
| ON (LED) |
LED |
| |
（with ION LED） | OFF | |
|
| |
Timing chart when the dirt on the electrode needle is detected
Power supply |
| ON |
|
|
|
|
|
|
|
|
Input | OFF |
|
|
|
|
|
|
|
| |
DC24V |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
Discharge stop |
| ON | (Operation) |
|
|
|
|
|
| |
signal | Input | OFF |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| |||||
Completion signal for |
| ON | (discharge) | Contamination detecting of electrode | ||||||
Output OFF |
|
|
|
|
|
| 2s |
| ||
Static charge |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| |||||
Maintenance |
| ON | （SW ON） | 100ms or more | ||||||
Input | OFF |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
Maintenance |
| ON | （SW ON） |
|
|
|
|
|
| |
output signal | Output OFF |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |||
Maintenance indication | ON | (LED) |
|
|
| Blink | ||||
| LED | OFF |
|
|
|
|
|
|
|
|
(With NDL CHECK ALARM) |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
ON and OFF status will be changed depending on the situation
・The completion signal for static charge elimination is output while the dirt on the electrode needle is being detected
・Because ions are discharged from the ionizer when the electrode needle is being detected, the workpiece might be charged. Therefore, the workpieces should not be mounted when the detection is executed.
15
