C | AA010012 | 2 Kw Radar processor box. No cables supplied. Connects to GB40 |
|
| system via Ethernet. |
|
| The Radar box requires heading @10hz. For Vessels using NMEA 0183 |
|
| order cable NS004801 to connect to a suitable heading sensor. |
|
| 2kW System is 12 V DC ONLY 25 W max Power connects to the two |
|
| screw terminals |
|
|
|
D | AA010151 | AT10HE SimNet to NMEA0183 converter Converts SimNet heading to |
|
| 0183 @10hz To allow for accurate MARPA and overlay. |
|
| Has two simnet ports to sit on simNet Bus and a 2 m (6ft) cable |
|
| terminating with 12 Pin Female connector. This plugs into socket |
|
| labeled NMEA COMS on the radar processor box |
|
|
|
D1 | NS004801 | Utility Cable 2 m (6ft) This cable has 12 Pin Female connector on one |
|
| end and 12 bare wires on the other. This plugs into socket labeled |
|
| Utility on the 8000i or GB40 Master Navcomputer this cable is shipped |
|
| with each NavComputer |
|
|
|
D2 | NS004801 | Same cable as D1 but needs to be ordered separately. Connects to the |
|
| radar processor labeled NMEA /COMS |
|
|
|
E |
| Ethernet Cables: All ethernet cables need to be ordered. They are not |
|
| supplied with any product. They are available in four lengths as well as |
|
| self terminating bulk rolls |
| NS004810 | Ethernet cable 0.5 m (1.6 ft) male / male connectors |
| NS004811 | Ethernet cable 2 m (6.5 ft) male / male connectors |
| NS004812 | Ethernet cable 5 m (16.5 ft) male / male connectors |
| NS004813 | Ethernet cable 0.5 m (1.6 ft) male / male connectors |
| NS004814 | Ethernet cable joiner 0.5 m (1.6ft) female / female |
| NS004817 | Ethernet cable bulk roll 100m (328 ft) |
| NS004818 | Ethernet cable bulk roll 300m (985 ft) |
| NS004816 | Ethernet Connector. Field terminating ethernet connector for bull |
|
| ethernet cable |
|
|
|
F | NS004815 | Ethernet |
|
| This can be used to connect no more than 2 network devices together |
|
| e.g a radar processor and a GB40 NavComputer. |
|
| The cable has Female connectors at each end. Two standard ethernet |
|
| cables are required to link to network devices. |
|
| Connector ends are red in colour |
|
| Tip: |
|
| When deciding which standard ethernet cables to order locate the |
|
| crossover joiner where logically a network linker could be placed in the |
|
| future if the system was upgraded |
|
| If more than 2 ethernet devices are going to be used please use the |
|
| Navico 8 Port Linker (see G) |
|
|
|
G | AA010009 | Navico 8 Port Ethernet Linker: Used to connect more then two ethernet |
|
| devices together. Ships with power cable only. Order ethernet cables |
|
| additionaly. 12 / 24 V DC |
|
|
|
H | 2209195 | RC42 Heading sensor (or use SimNet heading output from and |
|
| autopilot) |
|
|
|
H 1 | 2209195 | RC37 Race Compass or heading sensor with 10 Hz output. |
|
| Note: Make sure the heading sensor shares the same ground as the |
|
| NavComputer |
|
|
|
I |
| Simrad GB40 NavComputer |
|
|
|
I* |
| Simrad GB40 NavComputer second station |
|
|
|
Page 35
Image 35
