Connect to Lowrance Displays | Simrad MN000802A-G specification

10 Connect to Lowrance Displays

10.1 Parts needed to connect to Lowrance displays

RIM300 Radar Interface Module

Quantit	Item	Part name	Part No
y
1		Rim 300
		Cable


Heading Sensor (Optional)
Quantit	Item	Part Name	Part No
y
1		FC40 Fluxgate	22090245
		Compass
		OR	22090237
			22090237
		RC42 Rate
		Compass. This
		has a 5.5 m
		(18 ft) SimNet
		cable attached
		Connect using
		the below
		radar
		accessories kit

Radar Accessories kit (000-0127-45) Optional. Used to interface the above heading sensors

Quantit Item y

Part Name Part No

Simnet to	24005729
Micro C

Image 57

Simrad MN000802A-G manual Connect to Lowrance Displays, Parts needed to connect to Lowrance displays

Contents

KW Radar FCC Statement KW Radar Installation ManualIndustry Canada CE Compliance Feedback from you Warranty Contents Connect Simrad NX40 / NX45, Northstar M84 / M121 MaintenanceConnect Northstar 6000i Connect to Lowrance Displays 13 2 kW radar system specifications Ethernet Connectivity PrefaceSerial Connectivity Please Read Carefully Before USEPage Introduction to the Navico radar system Brand Display heads that support the Navico radar systemBranding information 2 kw Radar overview Serial Connectivity Install the radar Dont do this Choose the scanner location Power boat installations Yacht installations How to find the optimum height for the scannerScanner model Value half the -3 dB beam Width How to find the theoretical maximum detection range 2 kW scanner dimensions How to reduce false echoes and shadow zones Install the 2 kW scanner unit Install a scanner on a trestle Install the radar processor Check the 2 kW radar parts Page Page Wiring guidelines Page Page Page Yellow #24 White big #12 Shell Braid shield 2 kW radar processor connections Only Connect the power cable Radar system checklist Connect the ground wire Parts needed to connect radar to a GB40 or 8000i system Connect Simrad GB40 or NorthstarEthernet Cables Simrad GB40 and Northstar Ethernet Crossover cable Optional parts to connect GB40 only Optional parts to connect GB40AT10-HD Simrad GB40 connection using SimNet heading Key Part Description Number Northstar 8000i / Simrad GB 40 using Nmea 0183 headingPage Commision the radar using a GB40 or ¾ tarting up RadarPin Function ¾ Select OK to confirm the new setting ¾ Set Radar Range offset trigger Delay¾ To enter Radar setup options ¾ To correct Radar information Radar Power on Action Connect Simrad NX40 / NX45, Northstar M84 / M121 Parts neededRadar connection kit AA002461 Quanti Part name NOR Connect the 2 kW radar processor to an M84 or M121 Display ¾ To enable the radar functionality Set up the radar with the Northstar M84 or M121¾ Park position ¾ Zero bearing ¾ Antenna height Connect Northstar 6000i Parts needed to connct to a Northstar 6000iSerial comms extension cables + adaptor Quanti Part name Connect the 2 kW radar processor to a 6000i or 6100i display AUX NmeaPage Power Remote Power OUT ShieldNmea 1 in a Nmea 1 in BPage ¾ Power on Option ¾ Turn the radar off ¾ Turn on the radar as followsBefore you turn on the radar for the first time Turn the radar on Adjust the appearance settings Configure the navigator communications Heading sensor requirements Disable the heading sensor inputCalibrating the radar Prepare for calibration Tune the radar Set the trigger delaySet the STC Curve ¾ To select a different curve Set the heading calibration heading sensor installed Press Page 3, Page 4, and InstallPress Page 2, Page 3, Page 4, and Install Set the heading calibration heading sensor not installed Restore all the factory settingsRestore the factory appearance settings Manual tuning procedure for the 6000i or 6100i system ¾ Next, set the scale to 1/8 nautical miles as followsPress Sea Clutter Parts needed to connect to Lowrance displays Connect to Lowrance DisplaysRIM300 Radar Interface Module Quantit Part name Heading Sensor Optional Quantit Part Name 10.2 RIM300 Setup the radar with Lowrance displays Setup the basics ¾ Trigger Delay Preparation Radar Setup Main Bang Suppression Trigger Delay Adjust Main Bang Suppression Before heading line adjustment After heading line adjustment Maintenance General maintenanceScanner maintenance Other maintenance items Troubleshoot the radar Technical support, service and repairsRadar is not operating correctly If the scanner fails to turn How to reduce noise and interference Make sure the power is present and correctly wiredConfirm the equipment installed Make Model Serial Number Software Version Are range rings displayed? 13 2 kW radar system specifications KW scannerDC input To 15.6 V DC DC 12 V system only NS-RDR-1021MD KW Radar processor specifications