Manuals / Brands / Computer Equipment / Switch / SMSC / Computer Equipment / Switch

SMSC LAN8720, LAN8720i NAME, MODE, NAME, MODE, NAME, MODE, ADDRESS, DEFAULT, ADDRESS, DEFAULT, ADDRESS, DEFAULT, DESCRIPTION, DESCRIPTION, DESCRIPTION

1 79

Download 79 pages, 1.39 Mb

Small Footprint RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support

Datasheet

Table 5.27 Register 6 - Auto Negotiation Expansion

ADDRESS	NAME		DESCRIPTION	MODE	DEFAULT

6.15:5	Reserved			RO	0

6.4	Parallel Detection	1	= fault detected by parallel detection logic	RO/	0
	Fault	0	= no fault detected by parallel detection logic	LH

6.3	Link Partner Next	1	= link partner has next page ability	RO	0
	Page Able	0	= link partner does not have next page ability

6.2	Next Page Able	1	= local device has next page ability	RO	0
		0	= local device does not have next page ability

6.1	Page Received	1	= new page received	RO/	0
		0	= new page not yet received	LH

6.0	Link Partner Auto-	1	= link partner has auto-negotiation ability	RO	0
	Negotiation Able	0	= link partner does not have auto-negotiation ability

Table 5.28 Register 16 - Silicon Revision

ADDRESS	NAME	DESCRIPTION	MODE	DEFAULT

16.15:10	Reserved		RO	0

16.9:6	Silicon Revision	Four-bit silicon revision identifier.	RO	0001

16.5:0	Reserved		RO	0

Table 5.29 Register 17 - Mode Control/Status

ADDRESS	NAME	DESCRIPTION	MODE	DEFAULT

17.15:14	Reserved	Write as 0; ignore on read.	RW	0

17.13	EDPWRDOWN	Enable the Energy Detect Power-Down mode:	RW	0
		0 = Energy Detect Power-Down is disabled
		1 = Energy Detect Power-Down is enabled

17.12	Reserved	Write as 0, ignore on read	RW	0

17.11	LOWSQEN	The Low_Squelch signal is equal to LOWSQEN AND	RW	0
		EDPWRDOWN.
		Low_Squelch = 1 implies a lower threshold
		(more sensitive).
		Low_Squelch = 0 implies a higher threshold
		(less sensitive).

17.10	MDPREBP	Management Data Preamble Bypass:	RW	0
		0 – detect SMI packets with Preamble
		1 – detect SMI packets without preamble

17.9	FARLOOPBACK	Force the module to the FAR Loop Back mode, i.e. all	RW	0
		the received packets are sent back simultaneously (in
		100Base-TX only). This bit is only active in RMII
		mode, as described in Section 5.3.8.2. This mode
		works even if MII Isolate (0.10) is set.

17.8:7	Reserved	Write as 0, ignore on read.	RW	00

Revision 1.0 (05-28-09)	44	SMSC LAN8720/LAN8720i
	DATASHEET

Contents

LAN8720/LAN8720i Small Footprint RMII 10/100 Ethernet Transceiver with HP Auto-MDIXSupport PRODUCT FEATURES DATASHEET Table of Contents Page Page List of Figures List of Tables Page Chapter 1 Introduction 1.1General Terms and Conventions 1.2General Description RJ45 Crystal or 1.3Architectural Overview 1.3.1Configuration Figure 1.2 LAN8720/LAN8720i Architectural Overview Chapter 2 Pin Configuration 2.1Package Pin-outDiagram and Signal Table Table 2.1 LAN8720/LAN8720i 24-PINQFN Pinout PIN NO PIN NAME Chapter 3 Pin Description 3.1MAC Interface Signals 3.2LED Signals 3.3Management Signals 3.4General Signals 3.510/100 Line Interface Signals 3.6Analog Reference 3.7Power Signals Chapter 4 Architecture Details 4.1Top Level Functional Architecture 4.2100Base-TXTransmit 4.2.1100M Transmit Data Across the MII/RMII Interface 4.2.24B/5B Encoding 4.2.3Scrambling 4.2.4NRZI and MLT3 Encoding 4.2.5100M Transmit Driver 4.2.6100M Phase Lock Loop (PLL) 4.3100Base-TXReceive 4.3.1100M Receive Input 4.3.2Equalizer, Baseline Wander Correction and Clock and Data Recovery 4.3.3NRZI and MLT-3Decoding 4.3.4Descrambling 4.3.5Alignment 4.3.65B/4B Decoding 4.3.7Receive Data Valid Signal 4.410Base-TTransmit 4.4.110M Transmit Data Across the MII/RMII Interface 4.4.2Manchester Encoding 4.4.310M Transmit Drivers 4.510Base-TReceive 4.5.110M Receive Input and Squelch 4.5.2Manchester Decoding 4.5.310M Receive Data Across the MII/RMII Interface 4.5.4Jabber Detection 4.6MAC Interface 4.6.1RMII 4.7Reference Clock 4.7.1REF_CLK In Mode 4.7.2REF_CLK OUT Mode MAC RMII 10/100 PHY Mag Figure 4.5 LAN8720 sources REF_CLK from a 25MHz crystal 4.8Auto-negotiation Page 4.8.1Parallel Detection 4.8.2Re-starting Auto-negotiation 4.8.3Disabling Auto-negotiation 4.8.4Half vs. Full Duplex 4.9HP Auto-MDIXSupport 4.10nINTSEL Strapping and LED Polarity Selection 4.11REGOFF and LED Polarity Selection 4.12PHY Address Strapping 4.13Variable Voltage I/O 4.14Transceiver Management Control 4.14.1Serial Management Interface (SMI) Figure 4.10 MDIO Timing and Frame Structure - READ Cycle Figure 4.11 MDIO Timing and Frame Structure - WRITE Cycle Chapter 5 SMI Register Mapping Page Page Page 5.1SMI Register Format Table 5.21 Register 0 - Basic Control ADDRESS DEFAULT Table 5.22 Register 1 - Basic Status Table 5.22 Register 1 - Basic Status (continued) Table 5.23 Register 2 - PHY Identifier Table 5.24 Register 3 - PHY Identifier Table 5.25 Register 4 - Auto Negotiation Advertisement Table 5.25 Register 4 - Auto Negotiation Advertisement (continued) Register 5 - Auto Negotiation Link Partner Ability Table 5.27 Register 6 - Auto Negotiation Expansion Table 5.28 Register 16 - Silicon Revision Table 5.29 Register 17 - Mode Control/Status Table 5.29 Register 17 - Mode Control/Status (continued) Table 5.30 Register 18 - Special Modes Table 5.31 Register 26 - Symbol Error Counter Register 27 - Special Control/Status Indications Register 28 - Special Internal Testability Controls Table 5.34 Register 29 - Interrupt Source Flags Table 5.34 Register 29 - Interrupt Source Flags (continued) Table 5.35 Register 30 - Interrupt Mask Table 5.36 Register 31 - PHY Special Control/Status 5.2Interrupt Management 5.2.1Primary Interrupt System 5.2.2Alternate Interrupt System 5.3Miscellaneous Functions 5.3.1Carrier Sense 5.3.2Collision Detect 5.3.3Isolate Mode 5.3.4Link Integrity Test 5.3.5Power-Downmodes 5.3.6Reset 5.3.7LED Description 5.3.8Loopback Operation XFMR Digital Ethernet Transceiver 10/100 TXD X Digital 5.3.9Configuration Signals Table 5.39 MODE[2:0] Bus DEFAULT REGISTER BIT VALUES MODE[2:0] MODE DEFINITIONS REGISTER Chapter 6 AC Electrical Characteristics 6.1Serial Management Interface (SMI) Timing 6.2RMII 10/100Base-TX/RXTimings (50MHz REF_CLK IN) 6.2.1RMII 100Base-TTX/RX Timings (50MHz REF_CLK IN) CLKIN TXD[1:0] Page Page 6.3RMII 10/100Base-TX/RXTimings (50MHz REF_CLK OUT) 6.3.1RMII 100Base-TTX/RX Timings (50MHz REF_CLK OUT) 6.3.1.2100M RMII Transmit Timing (50MHz REF_CLK OUT) TXD[1:0] Page 6.4RMII CLKIN Requirements 6.5Reset Timing 6.6Clock Circuit Chapter 7 DC Electrical Characteristics 7.1DC Characteristics 7.1.1Maximum Guaranteed Ratings 7.1.2Operating Conditions 7.1.3Power Consumption Table 7.4 Power Consumption Device Only (REF_CLK IN MODE) VDDA3.3 TOTAL POWER CURRENT Page 7.1.4DC Characteristics - Input and Output Buffers Table 7.7 LAN Interface Signals Table 7.8 LED Signals Table 7.9 Configuration Inputs Table 7.10 General Signals Internal Pull-Up / Pull-DownConfigurations Internal Pull-Up / Pull-DownConfigurations (continued) Table 7.12 100Base-TXTransceiver Characteristics Table 7.13 10BASE-TTransceiver Characteristics Chapter 8 Application Notes 8.1Application Diagram 8.1.1RMII Diagram 8.1.2Power Supply Diagram 8.1.3Twisted-PairInterface Diagram 8.2Magnetics Selection Chapter 9 Package Outline Figure 9.1 QFN, 4x4 Taping Dimensions and Part Orientation Figure 9.2 Reel Dimensions Chapter 10 Revision History