Manuals / Brands / Computer Equipment / Switch / SMSC / Computer Equipment / Switch

SMSC LAN8720, LAN8720i (MA), DOWN, Note, Note, (MA), VDDCR, VDDIO, TOTAL, TOTAL, POWER, POWER, POWER, POWER, Note:, VDDCR, VDDIO, TOTAL, TOTAL, POWER, POWER, POWER, POWER, VDDA3.3

1 79

Download 79 pages, 1.39 Mb

Small Footprint RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support

Datasheet

Table 7.4 Power Consumption Device Only (REF_CLK IN MODE)

			VDDA3.3	VDDCR	VDDIO	TOTAL	TOTAL
			POWER	POWER	POWER	CURRENT	POWER
POWER PIN GROUP			PINS(MA)	PIN(MA)	PIN(MA)	(MA)	(MW)

		Max	27.1	20.4	0.6	48.1	158.7

100BASE-T /W TRAFFIC		Typical	25.7	18.5	0.5	44.7	147.5
100BASE-T /W TRAFFIC
		Min	22.4	17.4	0.3	40.1	95.3
							Note 7.1

		Max	9.7	13	0.6	23.3	76.9

10BASE-T /W TRAFFIC		Typical	8.9	11.8	0.5	21.2	70
10BASE-T /W TRAFFIC
		Min	8.3	11.1	0.3	19.7	41.3
							Note 7.1

		Max	4.2	3	0.2	7.4	24.4

ENERGY DETECT POWER		Typical	4.1	1.9	0.2	6.2	20.4
DOWN
DOWN		Min	3.9	1.9	0	5.8	15.2
		Min	3.9	1.9	0	5.8	15.2
							Note 7.1

		Max	0.4	2.8	0.2	3.4	11.2

GENERAL POWER DOWN		Typical	0.3	1.8	0.2	2.3	7.6
GENERAL POWER DOWN
		Min	0.3	1.7	0	2	3
							Note 7.1

Note: The current at VDDCR is either supplied by the internal regulator from current entering at VDD2A, or from an external 1.2V supply when the internal regulator is disabled.

Note 7.1 This is calculated with full flexPWR features activated: VDDIO = 1.8V and internal regulator disabled.

Note 7.2 Current measurements do not include power applied to the magnetics or the optional external LEDs.

7.1.3.2Power Consumption Device Only 50MHz REF_CLK OUT Mode

Power measurements taken over the operating conditions specified. See Section 5.3.5 for a description of the power down modes. For more information on 50MHz REF_CLK OUT mode, see Section 4.7.2

.

Table 7.5 Power Consumption Device Only (50MHz REF_CLK OUT MODE)

			VDDA3.3	VDDCR	VDDIO	TOTAL	TOTAL
			POWER	POWER	POWER	CURRENT	POWER
POWER PIN GROUP			PINS(MA)	PIN(MA)	PIN(MA)	(MA)	(MW)

		Max	27.7	20	6.3	54	178.2

100BASE-T /W TRAFFIC		Typical	25.8	18.1	5.8	49.7	164
100BASE-T /W TRAFFIC
		Min	21.2	14.1	2.9	38.2	92.1
							Note 7.3

Revision 1.0 (05-28-09)	68	SMSC LAN8720/LAN8720i
	DATASHEET

Contents

LAN8720/LAN8720i Small Footprint RMII 10/100 Ethernet Transceiver with HP Auto-MDIXSupport PRODUCT FEATURES DATASHEET Table of Contents Page Page List of Figures List of Tables Page Chapter 1 Introduction 1.1General Terms and Conventions 1.2General Description RJ45 Crystal or 1.3Architectural Overview 1.3.1Configuration Figure 1.2 LAN8720/LAN8720i Architectural Overview Chapter 2 Pin Configuration 2.1Package Pin-outDiagram and Signal Table Table 2.1 LAN8720/LAN8720i 24-PINQFN Pinout PIN NO PIN NAME Chapter 3 Pin Description 3.1MAC Interface Signals 3.2LED Signals 3.3Management Signals 3.4General Signals 3.510/100 Line Interface Signals 3.6Analog Reference 3.7Power Signals Chapter 4 Architecture Details 4.1Top Level Functional Architecture 4.2100Base-TXTransmit 4.2.1100M Transmit Data Across the MII/RMII Interface 4.2.24B/5B Encoding 4.2.3Scrambling 4.2.4NRZI and MLT3 Encoding 4.2.5100M Transmit Driver 4.2.6100M Phase Lock Loop (PLL) 4.3100Base-TXReceive 4.3.1100M Receive Input 4.3.2Equalizer, Baseline Wander Correction and Clock and Data Recovery 4.3.3NRZI and MLT-3Decoding 4.3.4Descrambling 4.3.5Alignment 4.3.65B/4B Decoding 4.3.7Receive Data Valid Signal 4.410Base-TTransmit 4.4.110M Transmit Data Across the MII/RMII Interface 4.4.2Manchester Encoding 4.4.310M Transmit Drivers 4.510Base-TReceive 4.5.110M Receive Input and Squelch 4.5.2Manchester Decoding 4.5.310M Receive Data Across the MII/RMII Interface 4.5.4Jabber Detection 4.6MAC Interface 4.6.1RMII 4.7Reference Clock 4.7.1REF_CLK In Mode 4.7.2REF_CLK OUT Mode MAC RMII 10/100 PHY Mag Figure 4.5 LAN8720 sources REF_CLK from a 25MHz crystal 4.8Auto-negotiation Page 4.8.1Parallel Detection 4.8.2Re-starting Auto-negotiation 4.8.3Disabling Auto-negotiation 4.8.4Half vs. Full Duplex 4.9HP Auto-MDIXSupport 4.10nINTSEL Strapping and LED Polarity Selection 4.11REGOFF and LED Polarity Selection 4.12PHY Address Strapping 4.13Variable Voltage I/O 4.14Transceiver Management Control 4.14.1Serial Management Interface (SMI) Figure 4.10 MDIO Timing and Frame Structure - READ Cycle Figure 4.11 MDIO Timing and Frame Structure - WRITE Cycle Chapter 5 SMI Register Mapping Page Page Page 5.1SMI Register Format Table 5.21 Register 0 - Basic Control ADDRESS DEFAULT Table 5.22 Register 1 - Basic Status Table 5.22 Register 1 - Basic Status (continued) Table 5.23 Register 2 - PHY Identifier Table 5.24 Register 3 - PHY Identifier Table 5.25 Register 4 - Auto Negotiation Advertisement Table 5.25 Register 4 - Auto Negotiation Advertisement (continued) Register 5 - Auto Negotiation Link Partner Ability Table 5.27 Register 6 - Auto Negotiation Expansion Table 5.28 Register 16 - Silicon Revision Table 5.29 Register 17 - Mode Control/Status Table 5.29 Register 17 - Mode Control/Status (continued) Table 5.30 Register 18 - Special Modes Table 5.31 Register 26 - Symbol Error Counter Register 27 - Special Control/Status Indications Register 28 - Special Internal Testability Controls Table 5.34 Register 29 - Interrupt Source Flags Table 5.34 Register 29 - Interrupt Source Flags (continued) Table 5.35 Register 30 - Interrupt Mask Table 5.36 Register 31 - PHY Special Control/Status 5.2Interrupt Management 5.2.1Primary Interrupt System 5.2.2Alternate Interrupt System 5.3Miscellaneous Functions 5.3.1Carrier Sense 5.3.2Collision Detect 5.3.3Isolate Mode 5.3.4Link Integrity Test 5.3.5Power-Downmodes 5.3.6Reset 5.3.7LED Description 5.3.8Loopback Operation XFMR Digital Ethernet Transceiver 10/100 TXD X Digital 5.3.9Configuration Signals Table 5.39 MODE[2:0] Bus DEFAULT REGISTER BIT VALUES MODE[2:0] MODE DEFINITIONS REGISTER Chapter 6 AC Electrical Characteristics 6.1Serial Management Interface (SMI) Timing 6.2RMII 10/100Base-TX/RXTimings (50MHz REF_CLK IN) 6.2.1RMII 100Base-TTX/RX Timings (50MHz REF_CLK IN) CLKIN TXD[1:0] Page Page 6.3RMII 10/100Base-TX/RXTimings (50MHz REF_CLK OUT) 6.3.1RMII 100Base-TTX/RX Timings (50MHz REF_CLK OUT) 6.3.1.2100M RMII Transmit Timing (50MHz REF_CLK OUT) TXD[1:0] Page 6.4RMII CLKIN Requirements 6.5Reset Timing 6.6Clock Circuit Chapter 7 DC Electrical Characteristics 7.1DC Characteristics 7.1.1Maximum Guaranteed Ratings 7.1.2Operating Conditions 7.1.3Power Consumption Table 7.4 Power Consumption Device Only (REF_CLK IN MODE) VDDA3.3 TOTAL POWER CURRENT Page 7.1.4DC Characteristics - Input and Output Buffers Table 7.7 LAN Interface Signals Table 7.8 LED Signals Table 7.9 Configuration Inputs Table 7.10 General Signals Internal Pull-Up / Pull-DownConfigurations Internal Pull-Up / Pull-DownConfigurations (continued) Table 7.12 100Base-TXTransceiver Characteristics Table 7.13 10BASE-TTransceiver Characteristics Chapter 8 Application Notes 8.1Application Diagram 8.1.1RMII Diagram 8.1.2Power Supply Diagram 8.1.3Twisted-PairInterface Diagram 8.2Magnetics Selection Chapter 9 Package Outline Figure 9.1 QFN, 4x4 Taping Dimensions and Part Orientation Figure 9.2 Reel Dimensions Chapter 10 Revision History