Manuals / Brands / Computer Equipment / Switch / SMSC / Computer Equipment / Switch

SMSC LAN8720, LAN8720i NAME, NAME, NAME, NAME, Note, NAME, Table, VIH (V), VIL (V), VOL (V), VOH (V), VIH (V), VIL (V), VOL (V), VOH (V), VIH (V), VIL (V), VOL (V), VOH (V)

1 79

Download 79 pages, 1.39 Mb

Small Footprint RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support

Datasheet

Table 7.7 LAN Interface Signals

NAME		VIH	VIL	IOH	IOL	VOL	VOH
TXP

TXN	See Table 7.12, “100Base-TX Transceiver Characteristics,” on page 72 and Table 7.13,

RXP		“10BASE-T Transceiver Characteristics,” on page 72.
RXP

RXN

Table 7.8 LED Signals

NAME	VIH (V)	VIL (V)	IOH	IOL	VOL (V)	VOH (V)
LED1/REGOFF	0.63 * VDD2A	0.39 * VDD2A	-12 mA	+12 mA	+0.4	VDD2A – +0.4

LED2/nINTSEL	0.63 * VDD2A	0.39 * VDD2A	-12 mA	+12 mA	+0.4	VDD2A – +0.4

Table 7.9 Configuration Inputs

NAME

VIH (V)

VIL (V)

IOH

IOL

VOL (V)

VOH (V)

RXD0/MODE0

0.68 * VDDIO

0.39 * VDDIO

-8 mA

+8 mA

+0.4

VDDIO – +0.4

RXD1/MODE1

0.68 * VDDIO

0.39 * VDDIO

-8 mA

+8 mA

+0.4

VDDIO – +0.4

RXER/PHYAD0

0.68 * VDDIO

0.39 * VDDIO

-8 mA

+8 mA

+0.4

VDDIO – +0.4

CRS_DV/MODE2

0.68 * VDDIO

0.39 * VDDIO

-8 mA

+8 mA

+0.4

VDDIO – +0.4

Table 7.10 General Signals

NAME

VIH (V)

VIL (V)

IOH

IOL

VOL (V)

VOH (V)

nINT/REFCLKO

-8 mA

+8 mA

+0.4

VDDIO – +0.4

nRST

0.63 * VDDIO

0.39 * VDDIO

XTAL1/CLKIN (Note 7.5)

+1.40 V

0.39 * VDD2A

XTAL2

-

-

Note 7.5 These levels apply when a 0-3.3V Clock is driven into XTAL1/CLKIN and XTAL2 is floating. The maximum input voltage on XTAL1/CLKIN is VDD2A + 0.4V.

Table 7.11	Internal Pull-Up / Pull-Down Configurations

NAME	PULL-UP OR PULL-DOWN

TXEN	Pull-down

RXD0/MODE0	Pull-up

SMSC LAN8720/LAN8720i	71	Revision 1.0 (05-28-09)
	DATASHEET

Contents

LAN8720/LAN8720i Small Footprint RMII 10/100 Ethernet Transceiver with HP Auto-MDIXSupport PRODUCT FEATURES DATASHEET Table of Contents Page Page List of Figures List of Tables Page Chapter 1 Introduction 1.1General Terms and Conventions 1.2General Description RJ45 Crystal or 1.3Architectural Overview 1.3.1Configuration Figure 1.2 LAN8720/LAN8720i Architectural Overview Chapter 2 Pin Configuration 2.1Package Pin-outDiagram and Signal Table Table 2.1 LAN8720/LAN8720i 24-PINQFN Pinout PIN NO PIN NAME Chapter 3 Pin Description 3.1MAC Interface Signals 3.2LED Signals 3.3Management Signals 3.4General Signals 3.510/100 Line Interface Signals 3.6Analog Reference 3.7Power Signals Chapter 4 Architecture Details 4.1Top Level Functional Architecture 4.2100Base-TXTransmit 4.2.1100M Transmit Data Across the MII/RMII Interface 4.2.24B/5B Encoding 4.2.3Scrambling 4.2.4NRZI and MLT3 Encoding 4.2.5100M Transmit Driver 4.2.6100M Phase Lock Loop (PLL) 4.3100Base-TXReceive 4.3.1100M Receive Input 4.3.2Equalizer, Baseline Wander Correction and Clock and Data Recovery 4.3.3NRZI and MLT-3Decoding 4.3.4Descrambling 4.3.5Alignment 4.3.65B/4B Decoding 4.3.7Receive Data Valid Signal 4.410Base-TTransmit 4.4.110M Transmit Data Across the MII/RMII Interface 4.4.2Manchester Encoding 4.4.310M Transmit Drivers 4.510Base-TReceive 4.5.110M Receive Input and Squelch 4.5.2Manchester Decoding 4.5.310M Receive Data Across the MII/RMII Interface 4.5.4Jabber Detection 4.6MAC Interface 4.6.1RMII 4.7Reference Clock 4.7.1REF_CLK In Mode 4.7.2REF_CLK OUT Mode MAC RMII 10/100 PHY Mag Figure 4.5 LAN8720 sources REF_CLK from a 25MHz crystal 4.8Auto-negotiation Page 4.8.1Parallel Detection 4.8.2Re-starting Auto-negotiation 4.8.3Disabling Auto-negotiation 4.8.4Half vs. Full Duplex 4.9HP Auto-MDIXSupport 4.10nINTSEL Strapping and LED Polarity Selection 4.11REGOFF and LED Polarity Selection 4.12PHY Address Strapping 4.13Variable Voltage I/O 4.14Transceiver Management Control 4.14.1Serial Management Interface (SMI) Figure 4.10 MDIO Timing and Frame Structure - READ Cycle Figure 4.11 MDIO Timing and Frame Structure - WRITE Cycle Chapter 5 SMI Register Mapping Page Page Page 5.1SMI Register Format Table 5.21 Register 0 - Basic Control ADDRESS DEFAULT Table 5.22 Register 1 - Basic Status Table 5.22 Register 1 - Basic Status (continued) Table 5.23 Register 2 - PHY Identifier Table 5.24 Register 3 - PHY Identifier Table 5.25 Register 4 - Auto Negotiation Advertisement Table 5.25 Register 4 - Auto Negotiation Advertisement (continued) Register 5 - Auto Negotiation Link Partner Ability Table 5.27 Register 6 - Auto Negotiation Expansion Table 5.28 Register 16 - Silicon Revision Table 5.29 Register 17 - Mode Control/Status Table 5.29 Register 17 - Mode Control/Status (continued) Table 5.30 Register 18 - Special Modes Table 5.31 Register 26 - Symbol Error Counter Register 27 - Special Control/Status Indications Register 28 - Special Internal Testability Controls Table 5.34 Register 29 - Interrupt Source Flags Table 5.34 Register 29 - Interrupt Source Flags (continued) Table 5.35 Register 30 - Interrupt Mask Table 5.36 Register 31 - PHY Special Control/Status 5.2Interrupt Management 5.2.1Primary Interrupt System 5.2.2Alternate Interrupt System 5.3Miscellaneous Functions 5.3.1Carrier Sense 5.3.2Collision Detect 5.3.3Isolate Mode 5.3.4Link Integrity Test 5.3.5Power-Downmodes 5.3.6Reset 5.3.7LED Description 5.3.8Loopback Operation XFMR Digital Ethernet Transceiver 10/100 TXD X Digital 5.3.9Configuration Signals Table 5.39 MODE[2:0] Bus DEFAULT REGISTER BIT VALUES MODE[2:0] MODE DEFINITIONS REGISTER Chapter 6 AC Electrical Characteristics 6.1Serial Management Interface (SMI) Timing 6.2RMII 10/100Base-TX/RXTimings (50MHz REF_CLK IN) 6.2.1RMII 100Base-TTX/RX Timings (50MHz REF_CLK IN) CLKIN TXD[1:0] Page Page 6.3RMII 10/100Base-TX/RXTimings (50MHz REF_CLK OUT) 6.3.1RMII 100Base-TTX/RX Timings (50MHz REF_CLK OUT) 6.3.1.2100M RMII Transmit Timing (50MHz REF_CLK OUT) TXD[1:0] Page 6.4RMII CLKIN Requirements 6.5Reset Timing 6.6Clock Circuit Chapter 7 DC Electrical Characteristics 7.1DC Characteristics 7.1.1Maximum Guaranteed Ratings 7.1.2Operating Conditions 7.1.3Power Consumption Table 7.4 Power Consumption Device Only (REF_CLK IN MODE) VDDA3.3 TOTAL POWER CURRENT Page 7.1.4DC Characteristics - Input and Output Buffers Table 7.7 LAN Interface Signals Table 7.8 LED Signals Table 7.9 Configuration Inputs Table 7.10 General Signals Internal Pull-Up / Pull-DownConfigurations Internal Pull-Up / Pull-DownConfigurations (continued) Table 7.12 100Base-TXTransceiver Characteristics Table 7.13 10BASE-TTransceiver Characteristics Chapter 8 Application Notes 8.1Application Diagram 8.1.1RMII Diagram 8.1.2Power Supply Diagram 8.1.3Twisted-PairInterface Diagram 8.2Magnetics Selection Chapter 9 Package Outline Figure 9.1 QFN, 4x4 Taping Dimensions and Part Orientation Figure 9.2 Reel Dimensions Chapter 10 Revision History