Case Upper | Sony MDS-NT1 guide

MDS-NT1

Note: Follow the disassembly procedure in the numerical order given.

3-2. CASE (UPPER)

Note 1: Fold down the flat type wire (7 core) in the direction of the arrow at the first setout, then install the upper case.

wire (flat type) (7 core)

2case (upper)

wire (flat type) (7core)

1 three screws (BVTP3 ⋅ 10)

lead wire

Note 2: Check that the lead wire is connected vertically to the chassis before installing the upper case.

If the lead wire is not connected vertically, it may be caught between the upper case.

chassis	chassis
lead wire	lead wire

OK

NG

1 three screws (BVTP3 ⋅ 10)

14

Image 14

Sony MDS-NT1 service manual Case Upper

Contents

Specifications MDS-NT1 Playback Recording Cause/Remedy Indicator Green Red MDS-NT1 SELF-DIAGNOSIS Function Items of Error History Mode Items and Contents MDS-NT1 Table of Error Codes Error Code Details of Error Diagrams Table of ContentsDisassembly SELF-DIAGNOSIS Function Flexible Circuit Board Repairing MDS-NT1 Section Servicing Notes BD Board Conductor Side JIG for Checking BD Board Waveform Record Procedure Checks Prior to Parts Replacement and Adjustments in MD Criteria for Determination Measure if unsatisfactory Microcomputer Version Display Service ModeSoftware Reset System Requirements MDS-NT1 Section General Front View MDS-NT1 Section Disassembly Disassembly Flow Case Upper Main Board MD Mechanism Deck MDM-7S2B Front Panel Section BD BOARD, Over Write Head HR901 Holder Assy Loading Motor Assy M103 Sled Motor Assy M102 Optical PICK-UP KMS-262E Spindle Motor Assy M101 Setting the Test Mode MDS-NT1 Section Test ModePrecautions for USE of Test Mode Releasing the Test Mode Selecting the Test Mode Check Operating the Continuous Playback Mode Automatic SELF-DIAGNOSIS Function Information Check before replacement MDS-NT1 Section Electrical AdjustmentsParts Replacement and Adjustment Adjustment flow YES HOW to Identify Optical PICK-UP KMS- 262A/KMS-262E Precautions for Checking Laser Diode EmissionPrecautions for USE of Optical PICK- UP KMS-262A/262E KMS-262A KMS-262E Precautions for Adjustments Laser power meter Laser Power Check Using the Continuously Recorded DiscTemperature Compensation Offset Check Checks Prior to Repairs Traverse Check Auto CheckOther Checks Focus Bias Check Play Check MO Error Rate CheckCD Error Rate Check Self-Recording/playback Check Laser Power Adjustment Initial Setting of Adjustment ValueTemperature Compensation Offset Adjustment Recording and Displaying the Iop Traverse Adjustment Iop NV Save Focus Bias Adjustment ENTER/YES button CD Auto Gain Control Output Level Adjustment Error Rate CheckAuto Gain Control Output Level Adjustment MO Auto Gain Control Output Level Adjustment Adjustment and Checking Loacation MDS-NT1 Section Diagrams Block Diagram Servo Section Block Diagram Main Section 36 a Waveforms BD Board 22.7 ns Printed Wiring Board BD Board Semiconductor Location 4AA 3AA Schematic Diagram BD Board 2/2 See page 38 for Waveforms B3B 2BB Printed Wiring Board Main Board Component Side IC451 Printed Wiring Board Main Board Conductor Side Main Board 1AA AA2 AA3 GND Printed Wiring Board Panel Board Panel Board Conductor Side Schematic Diagram Panel Board IC Block Diagrams BD Board CXA2523AR IC401 BH6519FS-E2 Main Board IC440 M54641L BD Board IC101 CXA2523AR RF AMP, FOCUS/TRACKING Error AMP IC PIN Function Description MNT2 Xbusy Xcas APC Main Board IC301 M30835FJGP-01 System Controller PLAY-SW Pin No Extal Section MDS-NT1 Exploded Views Case Section 56 4-951-620-01 Screw 2.6X8, +BVTP 104 105 Case B Section102 101 103 317 303 307 311 310 319 304 308302 306 320 301 305 313 314 315 316 364 359358 357 360 356 355 354 362 359 352 MDS-NT1 Section Electrical Parts List Resistors Diode Switch MDS-NT1 Main FB1 MDS-NT1 Main Panel Miscellaneous Motor ASSY, Loading Revision History