Playback and Recording 3 Chapter

Playback

This section describes playback of video and audio on the unit.

Before starting playback, make the following setting. Remote/local setting: Set the remote control switch. If

you set it to REMOTE, also set the setup menu item

INTERFACE SELECT >REMOTE I/F (“REMOTE” and the connector used appear on the display).

Disc playback start position

Although this unit uses optical discs, it is designed to offer the most convenient features of tape playback by VTRs.

After playback stop

The unit stops at the position where the STOP button was pressed.

Press the PLAY button to resume playback at the stop position.

After recording

The unit stops at the position where recording ended.

To play back a clip, press the PREV button to move to the start frame of any clip, or press the PREV button with the PLAY button held down to move to any position.

After disc insertion

The unit stops at the position of the disc when it was most recently ejected.

Press the PLAY button to resume playback at the most recent position.

The playback position is saved to the disc when the disc is ejected, which allows playback to start at that position whenever it is loaded into any XDCAM player.

Note

This function is not available when the Write Inhibit tab of the disc is set to the recording disabled position, and when REC INH on page P1 of the function menu is set to “ON”.

Playback Operation

First insert a disc.

EJECT

 

 

 

 

 

F1

 

 

 

 

 

 

 

 

 

 

 

 

 

F2

 

 

 

 

 

 

 

 

ACCESS

 

 

 

 

F3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NETWORK

 

 

 

 

F4

 

 

 

MENU

 

MARK1

 

VAR

 

 

 

 

 

CHAPTER

 

 

 

 

 

 

LOCAL

 

 

 

 

 

 

 

 

 

 

 

 

 

REMOTE

 

 

 

 

F5

EXPAND

SUB

THUMB

 

 

IN

OUT

 

LEVEL

 

 

 

 

 

 

CLIP

NAIL

SET

RESET

 

 

JOG

 

 

 

 

PAGE DISPLAY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLIP

ESSENCE

 

 

 

 

 

 

 

 

 

 

 

 

MENU

MARK

 

 

MARK2

 

 

PHONES

CH 1

CH 2

CH 3

CH 4

 

KEY INHI

PREV

PLAY

NEXT

STOP

REC

SHUTTLE

VARIABLE

 

 

 

 

 

 

 

 

 

 

 

 

 

REC

 

 

 

 

 

 

 

 

 

 

 

 

 

PRESET

 

 

 

 

 

 

 

 

 

 

 

 

 

PB

SHIFT

 

 

 

 

 

 

 

 

 

 

 

 

 

TOP

F REV

F FWD END

STANDBY

 

 

 

 

 

 

 

 

 

 

 

PREV button

PLAY button

NEXT button

STOP button

M/MARK1 button and m/MARK2 button

Jog dial

Shuttle dial

To start playback Press the PLAY button. Playback starts.

When two or more clips are recorded on the disc, they are played back continuously.

To jump to the next or previous clip, then start playback

Use the PREV button, NEXT button, jog dial, or shuttle dial.

To stop playback Press the STOP button.

If you play back to the end of the last clip, playback automatically stops.

If, in this state, you press the PLAY button, the message “ALARM DISC END.” appears on the display.

To carry out playback again, move back to the desired clip using the PREV button, jog dial or shuttle dial.

To set shot marks

While playing back a disc, you can set essence marks such as SHOT MARK1 and SHOT MARK2 in desired frames. To set a SHOT MARK1 or SHOT MARK2, hold down the M/MARK1 or m/MARK2 button and press the SET button.

Note

To erase or change essence marks, use the supplied PDZ-1 Proxy Browsing Software.

Searching for Clips With Thumbnails (Thumbnail Search)

You can display thumbnail images (index pictures) of all clips on the disc, and use them to cue up a desired clip.

36 Playback