Power amplifier section

Outputs: Speaker outputs (sure seal connectors)

Speaker impedance: 4 – 8 ohms

Maximum power output: 52 W ⋅ 4 (at 4 ohms)

General

Outputs:

Audio outputs terminal (front/rear)

Subwoofer output terminal (mono)

Power antenna relay control terminal

Power amplifier control terminal

Inputs:

Telephone ATT control terminal

Illumination control terminal

BUS control input terminal

BUS audio input/AUX IN terminal

Remote controller input terminal

Antenna input terminal

Tone controls:

Low: ±10 dB at 60 Hz or 100 Hz (XPLOD)

Mid: ±10 dB at 500 Hz or 1 kHz (XPLOD)

High: ±10 dB at 10 kHz or 12.5 kHz (XPLOD) Power requirements: 12 V DC car battery

(negative ground)

Dimensions: Approx. 178 ⋅ 50 ⋅ 183 mm (7 1/8 ⋅ 2 ⋅ 7 1/4 in) (w/h/d)

Mounting dimensions: Approx. 182 ⋅ 53 ⋅ 162 mm (7 1/4 ⋅ 2 1/8 ⋅ 6 1/2 in) (w/h/d)

Mass: Approx. 1.2 kg (2 lb 11 oz)

Supplied accessories:

Card remote commander: RM-X301

Parts for installation and connections (1 set)

Optional accessories/equipment:

Rotary commander: RM-X4S

BUS cable (supplied with an RCA pin cord): RC-61 (1 m), RC-62 (2 m)

CD changer (10 discs): CDX-757MX

CD changer (6 discs): CDX-T69

Source selector: XA-C40

AUX-IN selector: XA-300

Interface adaptor for iPod: XA-120IP

HD Radio™ tuner: XT-100HD

Your dealer may not handle some of the above listed accessories. Please ask the dealer for detailed information.

US and foreign patents licensed from Dolby Laboratories.

MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson.

Note

This unit cannot be connected to a digital preamplifier or an equalizer which is Sony BUS system compatible.

Design and specifications are subject to change without notice.

•Lead-free solder is used for soldering.

•Halogenated flame retardants are not used in the certain printed wiring boards.

•Halogenated flame retardants are not used in cabinets.

•Paper is used for the packaging cushions.

Troubleshooting

The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures.

If the problem is not solved, visit the following Support site.

Support site

If you have any questions or for the latest support information on this product, visit the web site below: http://esupport.sony.com http://www.sony.com/xplod

General

No power is being supplied to the unit.

•Check the connection. If everything is in order, check the fuse.

•If the unit is turned off and the display disappears, it cannot be operated with the remote commander. t Turn on the unit.

The power antenna does not extend. The power antenna does not have a relay box.

No sound.

•The volume is too low.

•The ATT function is activated, or the Telephone ATT function (when the interface cable of a car telephone is connected to the ATT lead) is activated.

•The position of the fader control is not set for a 2- speaker system.

•The CD changer is incompatible with the disc format (MP3/WMA/ATRAC CD).

t Play back with a Sony MP3 compatible CD changer, or this unit.

No beep sound.

•The beep sound is canceled (page 18).

•An optional power amplifier is connected and you are not using the built-in amplifier.

The contents of the memory have been erased.

•The RESET button has been pressed. t Store again into the memory.

•The power connecting lead or battery has been disconnected.

•The power connecting lead is not connected properly.

26