The name of the detected device does not appear.
Depending on the status of the other device, it may not be possible to obtain the name.
No ring tone.
•Adjust the volume in “Ring Vol” (page 16).
•Depending on the connecting device, the ring tone may not be sent properly.
t Set “Ringtone” to “Default” (page 17).
The talker’s voice volume is low.
Adjust the volume in “Talk Vol” (page 16).
Echo or noise occurs in phone call conversations.
•Lower the volume.
•“EC/NC Mode” is set to “off.”
tSet “EC/NC Mode” to “Mode 1” or “Mode 2” (page 18).
•If the ambient noise other than the phone call sound is loud, try reducing this noise.
E.g.: If a window is open and road noise, etc., is loud, shut the window. If the air conditioner is loud, lower the air conditioner.
The phone sound quality is poor.
Phone sound quality depends on reception conditions of cellular phone.
tMove your car to a place where you can enhance the cellular phone's signal if the reception is poor.
The volume of the connected audio device is low (high).
Volume level will differ depending on the audio device.
tAdjust the volume of the connected audio device or this unit.
No sound is heard from the Bluetooth audio device.
The audio device is paused.
tCancel pause of the audio device.
The sound skips during playback of a
Bluetooth audio device.
•Reduce the distance between the unit and the Bluetooth audio device.
•If the Bluetooth audio device is stored in a case which interrupts the signal, remove the audio device from the case while using.
•Several Bluetooth devices or other devices which emit radio waves are used nearby.
t Turn off the other devices.
t Reduce the distance from the other devices.
The connected Bluetooth audio device cannot be controlled.
Check that the connected Bluetooth audio device supports AVRCP.
Some functions do not work.
Check that the connecting device supports the functions in question.
The name of the other party does not appear when a call is received.
•The other party is not stored in the phonebook. t Store in the phonebook (page 16).
•The calling phone is not set to send the phone
28 number.
A call starts unintentionally.
•The connecting phone is set to start a call automatically.
•“Auto Answer” of this unit is set to “on” (page 17).
Pairing failed in Time Over.
Depending on the connecting device, the time limit for pairing may be short. Try completing the pairing within the time by setting a single digit passcode.
The ring tone or other party’s voice is output only from one speaker.
“Speaker Sel” is set to
tSet “Speaker Sel” to “Front” (page 18).
No sound is output from the car speakers during handsfree call.
If the sound is output from the cellular phone, set the cellular phone to output the sound from the car speakers.
Error displays/MessagesAudio functionBlank Disc
Tracks have not been recorded on the MD.
tPlay an MD with recorded tracks.
Error
•The disc is dirty or inserted upside down. t Clean or insert the disc correctly.
•The disc cannot play due to a problem. t Insert another disc.
Failure (Illuminates until any button is pressed.) The connection of speakers/amplifiers is incorrect.
tSee the installation guide manual of this model to check the connection.
FAILURE (Illuminates for about 1 second.)
When the XM tuner is connected, storing an XM radio channel into a preset failed.
tBe sure to receive the channel that you want to store, then try it again.
Load
The changer is loading the disc.
tWait until loading is complete.
Local Seek +/–
The local seek mode is on during automatic tuning.
NO Disc
The disc is not inserted in the CD/MD changer.
tInsert discs in the changer.
NO Disc Name
A disc name is not written in the track.
NO Group Name
A group name is not written in the track on the ATRAC CD.
NO ID3 Tag
ID3 tag information is not written in the MP3 file.
NO Information
Text information is not written in the ATRAC3/ ATRAC3plus or WMA file.
NO Magazine
The disc magazine is not inserted in the CD changer.
tInsert the magazine in the changer.