Print Audit Report, Sar, Store | Source Technologies ST9530 instruction

The values in field four of the Audit Trail Report can be added together with the total provided at the end of the report. This feature is activated through the MICR menu. Select Audit Menu>Sum Field 4.

The values in field 4 must follow certain guidelines to be included in the column summation. Dollar signs and commas must be properly located, no more than two numbers after a decimal point, and no alpha characters. For example:

Valid Formats	Invalid Formats
“$1,234,567.89”	“$1,23,”
“4321234.56”	“432.123”
“5,321”	“34 test”
“$.89”	“12$123”

If the value in field 4 is in an invalid format, that line will have a question mark to the right of the field and it will not be added to the total. Under these circumstances, the total will print with the notation “Fields flagged with ‘?’ not included in total.”

If the total exceeds $4,294,957,295.99 the printer will print an error message “Total exceeds maximum value” instead of the total.

Print Audit Report

Prints an Audit Trail Report.

The Audit Trail Report is also part of the command set so the Audit Report can be printed and purged via the host application. As a security control mechanism, purging is only possible after entering a valid password.

The printer can store approximately 6,000 records or checks for each megabyte of flash. If the Audit Report feature is activated, and the printer’s flash memory becomes full, an error condition occurs. The printer will stop printing and prompt the operator to print and purge the Audit Report memory. See the following section for purge instructions.

Audit Trail Report Command Set

&%SAR$	Start Audit Record
&%SAR	Lead in sequence
$	Command terminator

Marks the start of an audit record and begins a PJL job.. This command must be inserted in the datastream after MICR Mode is entered and before the first flagged field appears. It should be sent at the beginning of each check record.

End Audit Record	&%STORE$
&%STORE	Lead in sequence
Secure MICR Printer User’s Guide	37
September 2005	37

© Source Technologies All Rights Reserved

Image 41

Source Technologies ST9530 manual Print Audit Report, Audit Trail Report Command Set, Sar, End Audit Record, Store

Contents

ST9530 Secure Micr Printer User’s Guide Page Table of Contents Audit Trail Report Error Messages Printer Installation Micr Printing Today Micr OverviewCheck Processing System Secure Micr Printer User’s Guide Position and Dimension Gauge General Features of Check DesignMicr Check Design Design Elements in Detail Paper Micr Clear Band DuplexingData Elements Date Amount Convenience Amount Payee Area Amount In WordsSignature Area Drawee Institution Name Check Serial Number Fractional Routing Number Micr Line Memo LineAuxiliary On-Us Field Positions 65 to External Processing Code EPC Field Position On-Us Field Positions 32 to Sample Check Quality Issues Micr Check Stock WeightQuality Layout Check Stock Security Features Security Issues Security Note Secure Micr Printer User’s Guide Micr Mode Micr FeaturesMicr Fonts Secure Fonts @PJL Ustatus Device CODE=40020 MicroPrintBi-Directional Feedback Micr Menu Resource Storage STF Command Entering Micr Mode Password STH CommandMicr Definition Command SMCPxxxx$ optional Smcp STE Set New Password Command &%STExxxxxxxx$STS Print Micr E-13B Font SMDddd...ddd$ Print Secure Numeric Font SMFddd..ddd~ Print Micr CMC7 Font SM7ddd...ddd$Print ICR Secure Numeric Font &%SMIxxxxxx~ Print MicroPrint Line SMMxxxxxxxxx!$ Tray Lock Command STTL#$ Secure Flash Resource Unlock Command STPxxxxx$Load Flash Resource STLxxxxxyyyyyyzdd....dd Format Flash Memory SFF$ Tray Swapping Commands Tray Unlock Command STTU#$STTU# Sttson DES and AES Decryption Decryption Commands Turn AES Decryption on Turn DES Decryption onTurn DES Decryption OFF Turn AES Decryption OFF Customer Character Conversation Command STBEEP2$ Special Alert and Custom Beep CommandSTBEEP1$ MICRpoint Feature Secure Micr Printer User’s Guide Hex Transfer IBM Host Programming Features and ExamplesTurning Hex Transfer On Turning Hex Transfer Off Hex Transfer Examples Micr Mode Command Example STFPASSWORD$ Commands in .1 in order of appearanceCommand terminator Micr font character mapping in Appendix a STY4040$ Escape Character TranslationSTY4000$ Example &%STY2300$ Sample Check Audit Trail Reports Print Audit Report Audit Trail Report Command SetSAR End Audit Record Audit Report Field Two-MICR Line Audit Report Field One SQ1d..d$Audit Report Field Three SQ3d..d$ Audit Report Field Four SQ4d..d~ Audit Report Field Six SQ6d..d$ Audit Report Field Five SQ5d..d$Audit Report Field Seven SQ7d..d$ Print and Purge Audit Report &%SPURGExx$ Print Audit Report SPRINTxx$ Start Audit Feedback Command Audit Trail Commands Example Audit Trail Check Sample SQ1200$200 SAR$SQ6October 5, 2005$ Terminator SQ7103345 AM$ SMD...$ Msmith Error Message on Display Printed Message Error MessagesDescription Action Macro Definition Error Invalid decode Page Example &%SMD 00001234 T01234567T3210987654321$ Will print Appendix a E13B Micr Font Mapping Command&%SMDddd..ddd$ Appendix B CMC7 Micr Font Mapping Less Than Equal Greater Than Description Alpha/Numeric Hex Value Secure Font Character Appendix C Secure Numeric Font Mapping Two Three Four Five Six Seven Eight Nine Arrow Example&%SMF$15,575.00~ Appendix D ICR Secure Numeric Font Mapping Appendix E Micr Mode Command Summary STTSOFF$ STORE$ SPRINT$SPURGE$ Previous Audit Report information will be lost Appendix G PJL Based Micr Commands PJL Re-Lock Sequence With a New Password Value @PJL Info Micr UEL Cartridge Status = Unknown PCL Font Calls, Positioning Commands and Variable Print Data Sample Accounts Payable Check PJL and PCL commands used to print the sample check ESC%-12345X@PJL Ldeletepassword LRESOURCEflash