Uel, @PJL Info Micr | Source Technologies ST9530 manual

MICR FONT NOTE – The E-13B and CMC7 Fonts are 8 characters per inch. To position correctly at an exact 8 characters per inch, the printer must be set to an internal Unit of Measure of 600 DPI or greater or must have a horizontal motion index command at 8 CPI be issued after the font call. This is true even if the base printer is at 600 DPI. The default character positioning is at 300 DPI and 8 into 300 is 37.5 pixels. The printer will either round down to 37 or up to 38 pixels causing characters to creep. To resolve this there are multiple options.

1.If you are using a printer driver that is set to 600 DPI, the printer data stream should include a Unit of Measure PCL command set to 600. The command is <ESC>&u600D

2.If the application controls the printer data stream, add the Unit of Measure command early in the data stream. The command also affects X & Y positioning commands. Add <ESC>&u600D

3.After calling the E-13B MICR font, issue a HMI (Horizontal Motion Index) command set to 8 characters per inch. The command must be included with every E-13B MICR font call using either the Selection String or ID call. The command string is:

<ESC>(10O<ESC>(s0p8h8v0s7b360T<ESC>&k15H font data The Selection String <ESC>(30802X<ESC>&k15H font data The ID Call

See Font Mapping Appendix pages for specific character set data for each font.

PJL INFO MICR COMMAND

The ST Secure MICR Printer supports an optional custom bi-directional PJL Inquiry Command. The command provides printer information and cartridge information for network management. The command format is; @PJL INFO MICR

The command should be sent with UEL (Universal Exit Language) commands. Example:

<ESC>%-12345X	UEL
@PJL INFO MICR	INFO MICR Command
<ESC>%-12345X	UEL
The following data is returned
@PJL INFO MICR
PRINTER STATE	= READY

=BUSY

=NOT READY SERIAL NUMBER = XXXXXXXX

PAGECOUNT	= 123456
CARTRIDGE TYPE = NORMAL
	= MICR
Secure MICR Printer User’s Guide
September 2005	A13

© Source Technologies All Rights Reserved

Image 65

Source Technologies ST9530 manual Uel, @PJL Info Micr

Contents

ST9530 Secure Micr Printer User’s Guide Page Table of Contents Audit Trail Report Error Messages Printer Installation Micr Printing Today Micr OverviewCheck Processing System Secure Micr Printer User’s Guide Position and Dimension Gauge General Features of Check DesignMicr Check Design Design Elements in Detail Paper Micr Clear Band DuplexingData Elements Date Amount Convenience Amount Payee Area Amount In WordsSignature Area Drawee Institution Name Check Serial Number Fractional Routing Number Micr Line Memo LineAuxiliary On-Us Field Positions 65 to External Processing Code EPC Field Position On-Us Field Positions 32 to Sample Check Quality Issues Micr Check Stock WeightQuality Layout Check Stock Security Features Security Issues Security Note Secure Micr Printer User’s Guide Micr Mode Micr FeaturesMicr Fonts Secure Fonts @PJL Ustatus Device CODE=40020 MicroPrintBi-Directional Feedback Micr Menu Resource Storage STF Command Entering Micr Mode Password STH CommandMicr Definition Command SMCPxxxx$ optional Smcp STE Set New Password Command &%STExxxxxxxx$STS Print Micr E-13B Font SMDddd...ddd$ Print Secure Numeric Font SMFddd..ddd~ Print Micr CMC7 Font SM7ddd...ddd$Print ICR Secure Numeric Font &%SMIxxxxxx~ Print MicroPrint Line SMMxxxxxxxxx!$ Tray Lock Command STTL#$ Secure Flash Resource Unlock Command STPxxxxx$Load Flash Resource STLxxxxxyyyyyyzdd....dd Format Flash Memory SFF$ Tray Swapping Commands Tray Unlock Command STTU#$STTU# Sttson DES and AES Decryption Decryption Commands Turn AES Decryption on Turn DES Decryption onTurn DES Decryption OFF Turn AES Decryption OFF Customer Character Conversation Command STBEEP2$ Special Alert and Custom Beep CommandSTBEEP1$ MICRpoint Feature Secure Micr Printer User’s Guide Hex Transfer IBM Host Programming Features and ExamplesTurning Hex Transfer On Turning Hex Transfer Off Hex Transfer Examples Micr Mode Command Example STFPASSWORD$ Commands in .1 in order of appearanceCommand terminator Micr font character mapping in Appendix a STY4040$ Escape Character TranslationSTY4000$ Example &%STY2300$ Sample Check Audit Trail Reports Print Audit Report Audit Trail Report Command SetSAR End Audit Record Audit Report Field Two-MICR Line Audit Report Field One SQ1d..d$Audit Report Field Three SQ3d..d$ Audit Report Field Four SQ4d..d~ Audit Report Field Six SQ6d..d$ Audit Report Field Five SQ5d..d$Audit Report Field Seven SQ7d..d$ Print and Purge Audit Report &%SPURGExx$ Print Audit Report SPRINTxx$ Start Audit Feedback Command Audit Trail Commands Example Audit Trail Check Sample SQ1200$200 SAR$SQ6October 5, 2005$ Terminator SQ7103345 AM$ SMD...$ Msmith Error Message on Display Printed Message Error MessagesDescription Action Macro Definition Error Invalid decode Page Example &%SMD 00001234 T01234567T3210987654321$ Will print Appendix a E13B Micr Font Mapping Command&%SMDddd..ddd$ Appendix B CMC7 Micr Font Mapping Less Than Equal Greater Than Description Alpha/Numeric Hex Value Secure Font Character Appendix C Secure Numeric Font Mapping Two Three Four Five Six Seven Eight Nine Arrow Example&%SMF$15,575.00~ Appendix D ICR Secure Numeric Font Mapping Appendix E Micr Mode Command Summary STTSOFF$ STORE$ SPRINT$SPURGE$ Previous Audit Report information will be lost Appendix G PJL Based Micr Commands PJL Re-Lock Sequence With a New Password Value @PJL Info Micr UEL Cartridge Status = Unknown PCL Font Calls, Positioning Commands and Variable Print Data Sample Accounts Payable Check PJL and PCL commands used to print the sample check ESC%-12345X@PJL Ldeletepassword LRESOURCEflash