Non-Maskable Fault Group Descriptions | State Industries GFK-0827

4

Table 11.		Non-Maskable Fault Group Descriptions

	Table
Fault Group	Type		Description


SYS_BUS_FAIL	CPU		Systembus failure.

NO_USER_PRG	CPU		No User's Program on Power-up.

BAD_USER_RAM	CPU		Corrupted User RAM detected on Power-up.

WIND_CMPL_FAIL	CPU		Window Completion Failure in Constant Sweep Mode (i.e., all
			windows failed to receive their allotted time).

PASSWD_FAIL	CPU		PasswordAccess Failure.

NULL_SYS_CNFG	CPU		NULL System Configuration for RUN Mode.

CPU_SOFTWR	CPU		PLC CPU Software Failure.

TOO_MANY_IOCS	CPU		More than the allowable number of I/O Bus Controllers were
			found in the system.

SEQ_STORE_FAIL	CPU		Communicationfailure during a store operation by the program-
			mer. This fault results when the start-of-store sequence was
			received but not an end-of-storesequence.

Table 12. Non-Maskable Fault Action Descriptions

		Fault Actions

Fault Group	Simplex Mode		Redundant Mode


SYS_BUS_FAIL	Fatal		Fatal

NO_USER_PRG	Non-Fatal		Non-Fatal

BAD_USER_RAM	Fatal		Fatal

WIND_CMPL_FAIL	Non-Fatal		Non-Fatal

PASSWD_FAIL	Non-Fatal		Non-Fatal

NULL_SYS_CNFG	Non-Fatal		Non-Fatal

CPU_SOFTWR	Fatal		Fatal

TOO_MANY_IOCS	Fatal		Fatal

SEQ_STORE_FAIL		Fatal
		fatal

GFK-0827

Chapter 4 Operation

79

Image 90

State Industries GFK-0827 manual Non-Maskable Fault Group Descriptions, Non-Maskable Fault Action Descriptions

Contents

GE Fanuc Automation GFL±002 Content of this Manual Related Publications Preface We Welcome Your Comments and Suggestions Contents Chapter System Components Chapter Configuration Chapter Operation System Operation Fault Detection and Control Actions Synchronized Hot Standby CPU Redundancy System Configuration Contents Chapter Introduction Hot Standby CPU Redundancy Product GFK-0827 Features of the Hot Standby CPU Redundancy Product Benefits of the Hot Standby CPU Redundancy Product Local I/O System Systems for Hot Standby CPU Redundancy SystemsGenius I/O System Cable Connections Basic Hot Standby Operation Control Strategy Synchronized Hot Standby CPU Redundancy System Configuration Redundancy CPU Module Redundancy Communications Module Synchronized CPUs Bumpless SwitchingSwitch to Backup Unit Time Effect on Scan Time Configurable Backup Data Size On-Line ProgrammingOn-Line Repair Configuration Requirements Programming Considerations Definition of Terms Term Definition Commonly Used Acronyms Acronym Definition Chapter System Components Redundancy CPU Watchdog Timer CPU ArchitectureCapacities for Redundancy CPU, IC697CPU780 CPU Features Redundancy CPU IC697CPU CPU Mode Switch Valid Operating Mode Selection Memor y Protect Keyswitch Battery ConnectorsCPU Status LEDs Serial Port Connector Expansion Memory BoardExpansion Memory Boards for CPU RCM Features Redundancy Communications Module RCM System Status Leds Board OK RCM Connectors Unit Selection Pushbutton LED Status Indicators Bus Transmitter Module BTM Connectors Bus Receiver Module Bus Signal Termination BRM ConnectorsGenius Bus Controller Genius Bus Controller User Features GBC Connectors Racks Chapter Configuration Configuring a Hot Standby CPU Redundancy System System Configuration Basic Redundancy System SetupLogicmaster 90 Configuration Redundancy System Requirements Screens for Fault Category Configuration Monitor or Online mode Configuration with Logicmaster Handling Folders Configuration of a Redundancy CPU Module GFK-0827 Redundant CPU Requirements Normal Sweep Mode Redund TypeBackground Window Constant Window Sweep Mode Constant Sweep Mode Ctrl Strgy Fail WaitShared I/O Shared I/O Data Parameters Shared I/O Reference Values Transfer Data Size Reference Type ReferenceSize CalculationforNumberofBytes Configuring a CPU Expansion Memory Board Configuration of a Redundancy Communications Module Configuration Configuration of a Genius Bus Controller Paired GBC Parameter Serial Bus Address Configuring a Primary Redundant PLC Select the Redundancy CPU Module Select an Expansion Memory Board Configure the Redundant Communications Module Configure a Genius Bus Controller Configuration Configure Genius I/O Blocks Configure the Bus Transmitter Module Configuring a Secondary Redundant PLC Change Redund Type GFK-0827 Power-Up Sequence of a Redundant CPU Chapter Operation Incompatible Configurations Resynchronization of the Redundant CPU Hot-Standby Redundancy Control Strategy Synchronous Scan First Data Transfer %I, %AI and Synchronization Data Transfer from Backup Unit to Active Unit Switching Control to Backup Unit Second Data Transfer %Q, %AQ, %R, and %M Role Switch Svcreq References for CPU Redundancy Definition for% S Reference for Redundancy Status Redundancy CPU Considerations RUN Disabled Mode Differences in Operation for CPU RUN/ENABLED Locrdy Locact Remrdy Remact Configuration of Fault Actions Stop to RUN Mode Transition Background Window Time Words per Sweep = Timed Contacts Ovrpre %S Reference Genius Bus Controller Switching Fault Detection Fault Categories Changing Fault Category Actions PLC Fault Table Fault Zoom Help Text for Redundancy Error Codes Faulting RCMs, Losing Links, and Terminating Communications GFK-0827 Fault Actions in a CPU Redundancy System Maskable Fault Group Descriptions Maskable Fault Group Actions UserConfigurable Non-Maskable Fault Group Descriptions Non-Maskable Fault Action Descriptions On-Line Repair Maintaining Parallel Bus TerminationOn-Line Repair Recommendations Central Processor Unit Power SupplyRacks Redundancy Communications Module and Cables Redundancy Communications Link Failures Bus Transmitter ModuleGenius Bus Controller Genius Bus GeniusBlocks Appendix Redundancy Alternatives Redundancy Alternatives Redundancy Option Key See Table RedundancyOptions PLC Series 90-70 Redundancy Through Application Logic Index Index Index Index Index