Redundant Safety Controller Display | Sterling SDA 1000-5100

Redundant Safety Controller Display

Optional

The Redundant Safety Controller limits the process air temperature from exceeding the upper temperature range set by the E5CN Temperature Controller. Standard dryers use a microprocessor-based controller for limiting the process air temperature. The controller is a modular, self-contained unit removable from the mounting housing. All parameters are factory set and adjusted; normally, no field adjustment to the internal controls are necessary.

Figure 14: Typical Redundant Safety Controller Display

Setting the Redundant Safety Controller

The Redundant Safety Controller alarm setting is changed by pressing the up and down keys to input the alarm value. The upper display reading indicates the Process Value, while the lower display indicates the High Point Setting alarm value. The factory setting for the High

Point Alarm Value (L1-hi) is 150°F (-23°C).

Restoring the WATLOW Redundant Safety Controller to Factory Setup

If the preset parameters on the controller have been tampered with and it no longer functions properly, call the Service Department. This controller is not meant to be modified.

WATLOW Operating Parameters

The WATLOW controller has only one mode selection; ALARM.

The factory sets the security level to protect the critical parameters from being accidentally changed. Below is an explanation of the modes you will have access to and the manufacturer default settings.

Large Dehumidifying Dryers

Controls

33

Image 33

Sterling SDA 1000-5100 specifications Redundant Safety Controller Display, Setting the Redundant Safety Controller

Contents

SDA Large Dehumidifying Dryers With AP0 Controls Unpacking and Inspection Shipping InfoEvent of Shipping Damage If the Shipment is Not Complete Warranty Returns ReturnsCredit Returns Table of Contents Operation Dryer Identification Serial Number Tag Technical Assistance Safety How to Use This ManualSafety Symbols Used in this Manual Wear Safety Glasses and Work Gloves Dryer Safety Tags Description Responsibility General ResponsibilityOperator Responsibility Maintenance Responsibility Reporting a Safety Defect Functional Description Models Covered in This ManualGeneral Description Regeneration Cycle Process/Regeneration Cycle Sequence of Operation Controller Screen Descriptions Controller Description Standard Features Mechanical FeaturesElectrical Features Options Closed-Loop RegenerationProcess Aftercooler Recommended Temperature Settings Process Air Dust CollectorMaterial Overdrying Protection Electrical Options Mechanical Options Safety Circuit Standards Safety Devices and InterlocksSafety Device Lock-Outs Fail Safe OperationPage Uncrating the Equipment Mechanical InstallationRigging and Placing Unit Making Electrical Connections Checking Blower Rotation Checking for Proper Blower Rotation Dryer/Drying Hopper Process Air Connections Making Dryer/Drying Hopper Process Air Connections Aftercooler Components & Flow Rates Connecting Aftercooler/Precooler Cooling Water Optional Drying Hopper Air Trap Using the Drying Hopper Air Trap Indicator Lights SwitchesProcess Air Temperature Controller Controls Lit when Control Output 2 is on. Not used Lit when Control Output 1 is on. The Out1Indicator Name Description Lights in the Operation Indicator Section when E5CN Operating Parameters Setting the Process Air Temperature Tuned prior to dryer startup Adjustment Level Indicator Name Description ON, OFF Entering Operating Parameters to Select Modes Setting the High Dew Point Alarm Process Air Dew Point DisplayOptional Redundant Safety Controller Display Setting the Redundant Safety ControllerWatlow Operating Parameters Manf. setting Operation Auto-Tuning the DryerInitial Start-up Pre-Startup Checks Dryer Operation Procedures Page Material Miser OFF Press + to Enable Alarm Display Messages Shutting Down the Dryer Auto-Tuning the Dryer Maintenance Maintenance SchedulePhotocopy this page for your maintenance records Cleaning or Replacing the Process Air Filters Preventative Maintenance Calibrating the Dirty Filter Alarm Cleaning or Replacing the Regeneration Filter Checking the Dewpoint Control System Corrective Maintenance Symptoms of Worn Out DesiccantReplacing the Desiccant Replacing the Process Heater Electric Dryers Desiccant Tower Assembly Replacing the Regeneration Heater Electric Dryers Process Heater Box Assembly Regeneration Heater Box Assembly Troubleshooting Basic TroubleshootingIntroduction Large Dehumidifying Dryers Troubleshooting Alarms Alarm DescriptionsAlarm Alarm Description Alarm Effect Code Determining Temperature Controller Errors or Sensor Errors Using a ThermocoupleUsing a Platinum Resistance Thermometer Appendix Warranty Technical Specifications Aftercooler Design SpecificationsAnnex B Information Drawings and Diagrams Optional dryer dust collector Spare Parts List Level 3 Mechanical Components Located on back of Dryer Dryer Identification Serial Number Tag Parts and Service Department Technical Assistance Service DepartmentParts Department Sales Department