Belts and Ram Guards, Safety Markings | Sterling SXS Series manual

V-Belts and Ram Guards

V-belt and ram guards are bolted to the machine. They can be dismounted for installation and maintenance work when all rotating parts have come to a complete standstill and the machine is electronically locked out.

1

(1)	Ram guarding
(2)	V-belt guarding	2
(2)	V-belt guarding

NOTE: The operator must fit and mount the protective devices delivered with the machine according to the current legal safety regulations if the machine is delivered without drive motors upon customer request.

Safety Markings

Safety markings are attached to the machine. Should one of these markings becomes detached or is no longer recognizable, it must be replaced. New safety markings can be ordered through safety signage providers or from the manufacturer.

Personal Protective Gear

Wear close-fitting clothing. Hair must be pulled back, and loose fitting jewelry is prohibited. (See table below for more details.)

BJ5-620

Chapter 2: Functional Description

20 of 73

Image 20

Sterling SXS Series specifications Belts and Ram Guards, Safety Markings, Personal Protective Gear

Contents

SXS Extreme Duty Shredder Shipping Info Storage, Disposal, Transportation StorageDisposal Transportation Table of Contents Safety Symbols Used in this Manual SafetyHow to Use This Manual General Safety Regulations ResponsibilityPage Remaining Risks BJ5-620 Safety Page Functional Description Models Covered in This ManualGeneral Description Mechanical Section Material In-feed Typical Features and ComponentsMachine Standard Execution In-feed Hopper Additional In-feed Device Rotor, cutters, bed knives DriveRotor, Cutters, and Bed Knives Rotor cutter Screen and screen support Discharge of Shredded Material Hydraulic Ram Safety Features Personal Protective Gear Safety MarkingsBelts and Ram Guards Emergency Stop Button Re-operation Installation Unloading and Installing the MachineUncrating the Equipment Requirements at Application Site Electrical Connections Connection of Emergency Stop Button General Advice Initial Start-upChecking the Rotational Direction Machine Check Prior to Start-upPage Start-up Operation ProceduresOperation Emptying the Screen Hydraulic Set-up 12ml / r ec Switch OFF Machine Shut-down Maintenance Plan MaintenancePreventative Maintenance Schedule Checking the Protective Devices Preventative and Corrective MaintenanceCleaning the Machine Dismounting the Rotor Replacing the Gear BoxReplacing the Rotor Dismounting the Main Bearings Mounting the RotorReplacing the Main Bearings Mounting the Main Bearings Lubricating the Main Bearings Lubrication Intervals Shift Operation Replace Lubricant CheckCheck lubricant quality Replacing or Refilling Lubricant Refilling lubricant Replacing Lubricant BJ5-620 Maintenance Mounting and Dismounting TAPER-LOCK Tensioning Element Hydraulic Screen Support optional Tightening Torque of the ScrewsReplacing the Screen Belts Checking the tension force of the V-beltCentres and 16mm sag Profile section Efficiency of x Newton Lbs Re-tensioning and relaxing the V-belt Checking V-belt condition, replacing V-belt Working on the Cutting Knives Replacing and Checking the Cutting Knife MountingsTorque Grade Bolt type Checking the Condition of the Cutters Dismounting the Cutters Dismounting the Cutter Holders Dismounting the Bed Knives Mounting the Cutter Holders Make sure the cutter fits planar in the seat Make sure that the cutter holder fits properlyMounting the Cutters Adjust the gap between cutter and bed knife to 0.8-1.0 mm Mounting the Bed Knives Setting the Cutting Knives Sharpening Cutters and Bed Knives Fix the knife cover plates BJ5-620 Maintenance Hydraulic Maintenance Transporting and Storing the Cutting Knives Hydraulic liquid recommendation Troubleshooting Introduction Problem Possible Cause Possible Remedy Department Too many fines in shredded Reduce feed quantity Hydraulic Troubleshooting Warranty Returns AppendixReturned Material Policy Credit Returns Technical Specifications Drawings and Diagrams Cutter mounting Bed knife fixing Rotor Assembly Drive Ram Ram scraper SXS 1500/2000 Standard Hydraulic Diagram Spare Parts List SXS Knife rotor ø660x1500 Electrical parts Knife rotor ø660x1900 Hydraulic Unit Spare Parts List Pos Description Standard Supplier Technical Assistance Sterling, Inc Th Street New Berlin, WI