Sterling SXS Series instruction

9Switch ON machine for a short period of time and check rotational direction. The rotational direction can be seen at the discharge air fan of the drive motor (observe running direction arrow).

9Switch ON hydraulic unit for a short time and check rotational direction.

9Allow machine to run for approximately 10 minutes without shredding material.

9Connect material discharge device and in-feed device; check rotational direction drives.

9Feed grinding material uniformly. Too much material can lead to overload of the machine.

9Check the temperature of the ground material if necessary.

9Monitor the ammeter. This displays the present current consumption and gives information on the load of the machine.

BJ5-620

Installation

26 of 73

Image 26

Sterling SXS Series specifications

Contents

SXS Extreme Duty Shredder Shipping Info Disposal Storage, Disposal, TransportationStorage Transportation Table of Contents Safety Symbols Used in this Manual SafetyHow to Use This Manual General Safety Regulations ResponsibilityPage Remaining Risks BJ5-620 Safety Page General Description Functional DescriptionModels Covered in This Manual Mechanical Section Material In-feed Typical Features and ComponentsMachine Standard Execution In-feed Hopper Additional In-feed Device Rotor, cutters, bed knives DriveRotor, Cutters, and Bed Knives Rotor cutter Screen and screen support Discharge of Shredded Material Hydraulic Ram Safety Features Personal Protective Gear Safety MarkingsBelts and Ram Guards Emergency Stop Button Re-operation Uncrating the Equipment InstallationUnloading and Installing the Machine Requirements at Application Site Electrical Connections Connection of Emergency Stop Button Checking the Rotational Direction General AdviceInitial Start-up Machine Check Prior to Start-upPage Start-up Operation ProceduresOperation Emptying the Screen Hydraulic Set-up 12ml / r ec Switch OFF Machine Shut-down Maintenance Plan MaintenancePreventative Maintenance Schedule Checking the Protective Devices Preventative and Corrective MaintenanceCleaning the Machine Dismounting the Rotor Replacing the Gear BoxReplacing the Rotor Dismounting the Main Bearings Mounting the RotorReplacing the Main Bearings Mounting the Main Bearings Lubricating the Main Bearings Check lubricant quality Lubrication IntervalsShift Operation Replace Lubricant Check Replacing or Refilling Lubricant Refilling lubricant Replacing Lubricant BJ5-620 Maintenance Mounting and Dismounting TAPER-LOCK Tensioning Element Hydraulic Screen Support optional Tightening Torque of the ScrewsReplacing the Screen Centres and 16mm sag BeltsChecking the tension force of the V-belt Profile section Efficiency of x Newton Lbs Re-tensioning and relaxing the V-belt Checking V-belt condition, replacing V-belt Torque Grade Bolt type Working on the Cutting KnivesReplacing and Checking the Cutting Knife Mountings Checking the Condition of the Cutters Dismounting the Cutters Dismounting the Cutter Holders Dismounting the Bed Knives Mounting the Cutter Holders Make sure the cutter fits planar in the seat Make sure that the cutter holder fits properlyMounting the Cutters Adjust the gap between cutter and bed knife to 0.8-1.0 mm Mounting the Bed Knives Setting the Cutting Knives Sharpening Cutters and Bed Knives Fix the knife cover plates BJ5-620 Maintenance Hydraulic Maintenance Transporting and Storing the Cutting Knives Hydraulic liquid recommendation Troubleshooting Introduction Problem Possible Cause Possible Remedy Department Too many fines in shredded Reduce feed quantity Hydraulic Troubleshooting Returned Material Policy Warranty ReturnsAppendix Credit Returns Technical Specifications Drawings and Diagrams Cutter mounting Bed knife fixing Rotor Assembly Drive Ram Ram scraper SXS 1500/2000 Standard Hydraulic Diagram Spare Parts List SXS Knife rotor ø660x1500 Electrical parts Knife rotor ø660x1900 Hydraulic Unit Spare Parts List Pos Description Standard Supplier Technical Assistance Sterling, Inc Th Street New Berlin, WI