Manuals / Sterling / Computer Equipment / Paper Shredder

Sterling SXS Series specifications Shut-down, Switch OFF Machine

Models: SXS Series

1 73

Download 73 pages 34.8 Kb

Page 31

Image 31

4-3 Shut-down

Switch OFF Machine

1.Switch OFF the material in-feed device (accessories).

2.Wait until the remaining material has been shredded, and then switch OFF the shredder (main switch to 0).

3.Switch OFF the material discharge device.

BJ5-620

Operation

31 of 73

Page 31

Image 31

Sterling SXS Series specifications Shut-down, Switch OFF Machine

Contents

SXS SXS Extreme Duty ShredderIf the Shipment is Not Complete Shipping InfoUnpacking and Inspection In the Event of Shipping DamageDisposal Storage, Disposal, TransportationWARNING! Suspended load StorageTable of Contents 1-1How to Use This Manual Chapter 1 SafetySafety Symbols Used in this Manual 1-3Responsibility 1-2General Safety Regulations1-4Warnings and Precautions Possible Remaining RisksType of Danger ActivityBJ5-620 Chapter 1 Safety9 of BJ5-620 Mechanical Section Chapter 2 Functional Description2-1Models Covered in This Manual 2-2General DescriptionMachine Standard Execution 2-3Typical Features and ComponentsMaterial In-feed Additional In-feedDevice In-feedHopperRotor, Cutters, and Bed Knives DriveRotor, cutters, bed knives BJ5-620 Screen and screen support 17 of Discharge of Shredded MaterialBJ5-620 Chapter 2 Functional DescriptionHydraulic Ram Safety Device for Machine and Hopper Doors 2-4Safety FeaturesProtective Devices V-Beltsand Ram Guards Safety MarkingsPersonal Protective Gear Re-operation Emergency Stop ButtonRequirements at Application Site Chapter 3 InstallationUnloading and Installing the Machine 3-1Uncrating the Equipment3-2Electrical Connections 24 of InstallationConnection of Emergency Stop Button BJ5-620Machine Check Prior to Start-up General Advice3-3Initial Start-up Checking the Rotational DirectionBJ5-620 Installation26 of Switch ON Machine Chapter 4 Operation4-2Operation Procedures Machine Check-BeforeSwitching Machine ONEmptying the Screen Hydraulic Set-up 15MPa 12ml / r ec33ml / r ec 初始设定压力4-3 Shut-down Switch OFF Machine5-1Preventative Maintenance Schedule Chapter 5 MaintenanceCleaning the Machine 5-2Preventative and Corrective MaintenanceChecking the Protective Devices Replacing the Rotor Replacing the Gear BoxDismounting the Rotor Replacing the Main Bearings Mounting the RotorDismounting the Main Bearings Lubricating the Main Bearings Check Lubrication IntervalsShift Operation Replace LubricantReplacing Lubricant Refilling lubricantRoller Bearing Grease MaintenanceList of Recommended Lubricants Country of Manufacturer/ManufacturerBJ5-620 Maintenance40 of Replacing the Screen Tightening Torque of the ScrewsHydraulic Screen Support optional centres and 16mm sag Please refer to image from “Emptying the Screen”V-Belts Checking the tension force of the V-beltChecking V-beltcondition, replacing V-belt Re-tensioningand relaxing the V-beltBolt type Working on the Cutting KnivesTorque GradeDismounting the Cutter Holders Dismounting the CuttersDismounting the Bed Knives Mounting the Cutter Holders Mounting the Cutters 4.Make sure that the cutter holder fits properly5.Make sure the cutter fits planar in the seat Mounting the Bed Knives Sharpening Cutters and Bed Knives Setting the Cutting KnivesNOTE Recommended knife gap 0.8 mm - 1 mm Danger of cutting caused by sharp knives 53 of MaintenanceHydraulic liquid recommendation BJ5-6206-1Introduction Chapter 6 Troubleshootingservice department ProblemTroubleshooting consulting the serviceBJ5-620 Troubleshootingconsulting the service consulting the service57 of Troubleshootingconsulting the service BJ5-62058 of Hydraulic TroubleshootingTroubleshooting BJ5-620Credit Returns AppendixWarranty Returns A-1Returned Material Policy60 of A-2Technical SpecificationsBJ5-620 AppendixCutter mounting A-3Drawings and Diagrams62 of Bed knife fixingBJ5-620 Appendix63 of Rotor AssemblyBJ5-620 Appendix64 of DriveBJ5-620 AppendixAppendix BJ5-62065 of 66 of Ram scraperBJ5-620 Appendix15MPa SXS 1500/2000 Standard Hydraulic Diagram12ml / r ec 初始设定压力Screen complete Hydraulic A-4Spare Parts ListDescription/Standard Machine completeE-kniferotor ø660x1500 BJ5-620Appendix 69 ofScreen complete Hydraulic Electrical partsDescription/Standard Machine completeE-kniferotor ø660x1900 BJ5-620Appendix 71 ofDescription Hydraulic Unit Spare Parts ListHydraulic Electrical partsParts Department Service DepartmentA-5Technical Assistance Sterling, Inc 2900 S. 160th Street New Berlin, WI