Flywheel FAN and Drive Shaft | Subaru Robin Power Products RG3200I

5-4-4 FLYWHEEL FAN and DRIVE SHAFT

(1)Install the Flywheel Fan to the flywheel so as that the three alignment tabs on the back of flywheel fan to mate with the holes of the flywheel.

(2)Assemble the Drive Shaft onto the flywheel.

Tighten the four M8 bolts while holding the drive shaft using the special tool “Drive Shaft Holder”.

M8 x 27mm Flange bolt : 4pcs.

Tightening torque : 25.0-27.0 N・m 250-270 kgf・cm (18.4-19.9 ft・lbs)

5-4-5 BLOWER HOUSING

(1)Assemble the Blower Housing onto the crankcase. M6 x 35mm Bolt : 1 pce.

M6 x 45mm Bolt : 3 pcs.

Tightening torque : 8.0-10.0 N・m 80-100 kgf・cm (5.9-7.4 ft・lbs)

(2)For the soundproof type only, assemble the Separator (A/C) and Separator (SEL) to the blower housing.

M6 x 8mm Flange bolt : 3 pcs.

M6 x 12mm Flange bolt : 1 pce.

Tightening torque : 4.0-6.0	N・m
40-60	kgf・cm
(3.0-4.4	ft・lbs)

5-4-6 BOTTOM EXTENSION PLATE

Assemble the Bottom Extension Plate to the engine. M8 x 33mm Flange bolt for crankcase side : 2 pcs.

M8 x 12mm Flange bolt for blower housing side : 2 pcs.

Tightening torque : 18.0-22.0 N・m 180-220 kgf・cm (13.3-16.2 ft・lbs)

Drive shaft

Drive shaft holder

Blower housing

M6x35mm Bolt

Separator (A/C)

M6x45mm

Bolt

Separator (SEL)

Bottom extension plate

– 39 –

Image 42

Subaru Robin Power Products RG3200IS, RG4300I Flywheel FAN and Drive Shaft, Blower Housing, Bottom Extension Plate

Contents

Generators Page Contents NGK BR6HS SpecificationsModel RG2800i RG3200i RG4300i STD Model RG2800iS RG3200iS RG4300iS General Description External View of Generator Open Frame Type RG4300i External View of Generator Sound Proof Type RG2800iS RG3200iS / RG4300iS 60Hz-120V Control Panel50Hz-230V 50Hz-240V Engine Switch Multi Monitor Location of Serial Number and Production Number Alternator Incandescent lamp, heater, etc. with a power factor Mercury lamps with a smaller power factorRange of Applications Appliances without any indication as to power consumption Cross Allowable Cable Voltage drops per 30 meters of cable Voltmeter Measuring and Checking ProceduresMeasuring Instruments Ammeter Circuit Tester Meager TesterTachometer Specifications ModelDr.RobinPartNumber388-47565-08 AC Output Measuring DC Output Measuring Measuring Insulation Resistance StatorControl Panel Checking Functional Members Output Wires4P Connector RG2800i RG3200i RG4300i RG2800iS RG3200iS RG4300iS Checking table for degital circuit tester Diode RectifierChecking table for analogue circuit tester AC Receptacles DC Circuit Breaker Float Type OIL Sensor Special Tools Disassembly and AssemblyPreparation and Precautions Part Number Part Name Shape Usage Side Cover L and R Disassembly ProceduresFuel PIPES, Fuel Strainer and Battery Cables Starter Handle For electric start models Grounding WireChoke Wire Control Panel and Inverter Unit Wire Band Rear Cover Fuel Tank Fuel Tank and Fuel System Parts Wire Harness Autothrottle Coupler Control BOX and Inverter Unit Components and Control BOX ComponentsInverter Unit Components Control BOX Components RG2800i / RG3200i / RG2800iS Control Panel Control BOX Components RG4300i / RG3200iS / RG4300iS Foam Rubber Insulators Muffler CoverMuffler AIR Cleaner and Carburetor Engine Block Open Frame TypeSoundproof Type Through Bolt and Rotor Alternator Components Blower Housing Recoil StarterBottom Extension Plate Drive Shaft and FAN Flywheel Sound Insulator Reassembly ProceduresMount Rubbers For SOUND-PROOF Models Tightening torque 8.0-10.0 N・m 80-100 kgf・cm 5.9-7.4 ft・lbs Blower HousingFlywheel FAN and Drive Shaft Tightening torque 40-60 Kgf ・cm 4.4 Ft ・lbs Rear Cover Recoil StarterTightening torque 6.5-8.5 N・m 65-85 kgf・cm 6.3 ft・lbs Through Bolt thread in reverse direction Installation of Engine Alternator Assembly Onto Frame Carburetor AIR Cleaner BaseAIR Cleaner Element Tightening torque 6.0-8.0 N・m 60-80 kgf・cm 5.9 ft・lbs Muffler Muffler Cover Grounding Wires Connection of Wiring HarnessControl BOX and Inverter Unit Fuel Tank Clamping of the Choke Cable and Ground WiresAuto Throttle Tightening torque 4.0-6.0 N・m 40-60 kgf・cm 4.4 ft・lbs Rear Cover Upper Muffler Cover Rear Ground Wire Recoil Starter Handle Side Cover Disassembly procedures Recoil Starter Disassembly is completed Assembly procedure Five turns in counter-clockwise Checking items after assembly When Trouble Shooting No output power or Low output Improper revolutions Electronic throttle Engine does not start Start failure Wiring Diagram RG2800i / RG3200i / RG2800iS 50Hz-230V Recoil starter model Relay RG2800i / RG3200i / RG2800iS 50Hz-240V Recoil starter model AC receptacle Earth ground terminal Engine 240V Switch Fuse10A Engine 120V Switch RG2800i / RG3200i / RG2800iS 60Hz-120V Recoil starter model Diode DC output Terminal Rectifier Coil Page Lively Blvd. Wood Dale, IL 60191 Phone 630-350-8200 Fax