Sun GigaSwift Ethernet MMF Adapter | Sun Microsystems X1150A

Sun GigaSwift Ethernet MMF Adapter

The Sun GigaSwift Ethernet MMF adapter is a single-port gigabit Ethernet fiber optics PCI Bus card. It operates in 1000 Mbps Ethernet networks only.

FIGURE 1-1Sun GigaSwift Ethernet MMF Adapter

LED Displays

Four LEDs are displayed on the front panel of Sun GigaSwift Ethernet MMF adapter. They are labeled on the front panel as shown in TABLE 1-1.

TABLE 1-1Front Panel Display LEDs for the MMF Adapter

Label	Meaning if Lit	Color

Link	Link is up	Green
FDX	Link is in Full Duplex mode.	Green
TX	Link is transmitting	Green
RX	Link is receiving	Green

2 Sun GigaSwift Ethernet Adapter Installation and User’s Guide • February 2003

Image 24

Sun Microsystems X1150A manual Sun GigaSwift Ethernet MMF Adapter, LED Displays, Link is in Full Duplex mode

Contents

Sun GigaSwift Ethernet Adapter Installation User’s Guide Please Recycle Regulatory Compliance Statements FCC Class a Notice ICES-003 Class a Notice Avis NMB-003, Classe a Bsmi Class a Notice Page Declaration of Conformity European UnionPage Declaration of Conformity Page Contents Network Configuration Configuring Driver Parameters Configuring VLANs SpecificationsDiagnostic Software and Troubleshooting Issues IndexPage Figures Page Tables Performance Sepcifications Preface How This Book Is Organized Using Unix Commands Typographic Conventions Accessing Sun Documentation Online Shell PromptsRelated Documentation Sun Welcomes Your Comments Product Overview Hardware Overview Link is in Full Duplex mode Sun GigaSwift Ethernet MMF AdapterLED Displays 1Front Panel Display LEDs for the MMF Adapter Sun GigaSwift Ethernet UTP Adapter 2Sun GigaSwift Ethernet UTP Adapter 2Front Panel Display LEDs for the UTP Adapter Hardware and Software Requirements Patch Requirements Product Features Key Protocols and Interfaces Diagnostic Support Page Installing the Driver Software Become superuser 1Files and Directories on the CD-ROM Select the packages you want to install Menu similar to the following displays Verifying Patches Patch version should be -07 or greater# showrev -p grep Patch version should be -13 or greater Patch version should be -05 or greater Installing the Adapter Without Dynamic Reconfiguration To Install the AdapterSave the filler panel screw for Step 1Connecting the Fiber Optic Cable To Verify the Installation 2Cat-5 Twisted-Pair Cable List the network devices on your system Ok show-netsOk cd /pci@1f,0/pci@1/network@4 View the.properties file for a list of device properties Ok .properties Setting the local-mac-addressProperty Phy-typewill have its value assigned as followsOk setenv local-mac-address? true Rebooting the System Ok setenv boot-device /pci@1f,2000/pci@1/network@4Ok boot -r Installing the Adapter With Dynamic Reconfiguration To Install an Adapter in a Dynamic Reconfiguration SystemStates and conditions should be # cfgadm # cfgadm -v -c configure sysctrl#slot# # cfgadm -c disconnect sysctrl#slot## cfgadm -c disconnect sysctrl03 Configure the adapter and slot Reconfigure the devices on the adapter# drvconfig devlinks disks ports tapes Connect the adapter and slotPage Configuring the Network Host Files Use the ifconfig command to setup the adapter’s ce interface # ifconfig ce0 plumb ipaddress up To Set Up a GigaSwift Ethernet Port on a Diskless Client # cat /etc/hostsExport/root/clientname Edit the hosts in the diskless client’s root directory Network Configuration # grep clientname /etc/bootparams Find the root directory of the client system# cd /cdrom/cdrom0/GigaSwiftEthernet/Packages # ls SUNWce Use the shutdown command to display the OpenBoot ok prompt Shut down and halt the client system# shutdown -i0 -g0 -y Proceed with the Solaris operating environment installation Ok boot /pci@1f,4000/network@4speed=100,duplex=full# pkginfo grep SUNWce Booting Over the GigaSwift Ethernet Network Ok boot device-pathspeed=s,duplex=d,link-clock=c,promiscuous 1Device Link Parameters 2link-clockCapabilities for Link Up # boot netspeed=100,duplex=full # boot netspeed=1000,duplex=full,link-clock=master# boot netspeed=1000,duplex=auto,link-clock=auto Page Configuring Driver Parameters GigaSwift Ethernet Device Driver Parameters Driver Parameter Values and Definitions 1ce Driver Parameter, Status, and Descriptions Operational Mode Parameters Operational Mode Parameters 2Operational Mode Parameters Flow Control Parameters 3provides flow control keywords and describes their function 3Read-Write Flow Control Keyword Descriptions 4Forced Mode Parameter Gigabit Link Clock Mastership ControlsInterpacket Gap Parameters 5Parameters Defining enable-ipg0and ipg0 Interrupt Parameters 7describes the receive interrupt blanking values7RX Blanking Register for Alias Read Random Early Drop Parameters 8RX Random Early Detecting 8-Bit Vectors PCI Bus Interface Parameters 9PCI Bus Interface Parameters Setting ce Driver Parameters Setting Parameters Using the ndd Utility To Specify Device Instances for the ndd Utility Use the instance number to select the deviceDevice remains selected until you change the selection # ndd -set /dev/ce instance instance# To modify a parameter value, use the -setoption Ndd utility then prompts you for the name of the parameter# ndd -set /dev/ce parameter value # ndd /dev/ce parameter Setting the Autonegotiation Mode Setting Parameters Using the ce.conf File Set the adv-autoneg-capparameter to# ndd -set /dev/ce adv-autoneg-cap To Set Driver Parameters Using a ce.conf File Second line in the previous example# grep ce /etc/pathtoinst Usability Enhancements to the Driver Third line in the previous exampleSave the ce.conf file # ndd -set /dev/hme instance GigaSwift Ethernet Driver Operating Statistics Then you had to get the link status# ndd -get /dev/hme link-status # kstat cen grep linkup 10Read-Only ce Device Capabilities Reporting the Link Partner Capabilities 11describes the read-only link partner capabilities11Read-Only Link Partner Capabilities 12describes the netstat -k transmit and receive parameters 12Transmit and Receive Parameters 12Transmit and Receive Parameters Code Example 4-1Output from kstat Command # netstat -k ce0# kstat Ce0 # kstat ce0 # kstat ce0 Use the kstat command to discover link partner capabilities # kstat ce0 grep lp Use the kstat command to discover link settings # kstat ce0 grep linkPage Configuring VLANs An Overview of VLANs 1shows an example network that uses VLANs Configuring VLANs To Configure Static VLANs Vlan logical PPA = 1000 * VID + Device PPA # ifconfig ce123000 plumb up # ifconfig ce224000 plumb up # ifconfig -aPage Connectors Table A-1SC Connector Link Characteristics Ieee P802.3z Performance Specifications Table A-2Cat-5 Connector Link CharacteristicsTable A-3Performance Sepcifications Physical Characteristics Power RequirementsTable A-5Power Requirements Page Diagnostic Software Troubleshooting Issues SunVTS Diagnostic Software Using the OpenBoot Prom FCode Self- Test Running the Ethernet FCode Self-Test DiagnosticReset the system Shut down the system Ok setenv diag-switch? false Type show-netsto display the list of devicesOk test /pci@1f,0/pci@1/network@4 Troubleshooting Issues Set the auto-boot?configuration parameter to trueReset and reboot the system Ok setenv auto-boot? true Type the following to apply and save your changes Adv-pause-cap Failure to Configure GigaSwift Ethernet Instance Non-Specific IssuesTable B-1Troubleshooting the GigaSwift Ethernet Adapter Problem with DR Attach on Sun Enterprise Platforms Reboot systemAdd the following lines to the /etc/system file Set drdetachsafelist1=ce set hswpsuspendsafelist1=cePage Symbols Index