Network Configuration
# grep clientname /etc/bootparams
Find the root directory of the client system
# cd /cdrom/cdrom0/GigaSwiftEthernet/Packages # ls SUNWce
Use the shutdown command to display the OpenBoot ok prompt
Shut down and halt the client system
# shutdown -i0 -g0 -y
Proceed with the Solaris operating environment installation
Ok boot /pci@1f,4000/network@4speed=100,duplex=full
# pkginfo grep SUNWce
Booting Over the GigaSwift Ethernet Network
Ok boot device-pathspeed=s,duplex=d,link-clock=c,promiscuous
1Device Link Parameters
2link-clockCapabilities for Link Up
# boot netspeed=100,duplex=full
# boot netspeed=1000,duplex=full,link-clock=master
# boot netspeed=1000,duplex=auto,link-clock=auto
Page
Configuring Driver Parameters
GigaSwift Ethernet Device Driver Parameters
Driver Parameter Values and Definitions
1ce Driver Parameter, Status, and Descriptions
Operational Mode Parameters
Operational Mode Parameters
2Operational Mode Parameters
Flow Control Parameters
3provides flow control keywords and describes their function
3Read-Write Flow Control Keyword Descriptions
4Forced Mode Parameter
Gigabit Link Clock Mastership Controls
Interpacket Gap Parameters
5Parameters Defining enable-ipg0and ipg0
Interrupt Parameters
7describes the receive interrupt blanking values
7RX Blanking Register for Alias Read
Random Early Drop Parameters
8RX Random Early Detecting 8-Bit Vectors
PCI Bus Interface Parameters
9PCI Bus Interface Parameters
Setting ce Driver Parameters
Setting Parameters Using the ndd Utility
Device remains selected until you change the selection
To Specify Device Instances for the ndd Utility
Use the instance number to select the device
# ndd -set /dev/ce instance instance#
# ndd -set /dev/ce parameter value
To modify a parameter value, use the -setoption
Ndd utility then prompts you for the name of the parameter
# ndd /dev/ce parameter
Setting the Autonegotiation Mode
Setting Parameters Using the ce.conf File
Set the adv-autoneg-capparameter to
# ndd -set /dev/ce adv-autoneg-cap
To Set Driver Parameters Using a ce.conf File
Second line in the previous example
# grep ce /etc/pathtoinst
Save the ce.conf file
Usability Enhancements to the Driver
Third line in the previous example
# ndd -set /dev/hme instance
# ndd -get /dev/hme link-status
GigaSwift Ethernet Driver Operating Statistics
Then you had to get the link status
# kstat cen grep linkup
10Read-Only ce Device Capabilities
Reporting the Link Partner Capabilities
11describes the read-only link partner capabilities
11Read-Only Link Partner Capabilities
12describes the netstat -k transmit and receive parameters
12Transmit and Receive Parameters
12Transmit and Receive Parameters
Code Example 4-1Output from kstat Command
# netstat -k ce0
# kstat Ce0
# kstat ce0
# kstat ce0
Use the kstat command to discover link partner capabilities
# kstat ce0 grep lp
Use the kstat command to discover link settings
# kstat ce0 grep link
Page
Configuring VLANs
An Overview of VLANs
1shows an example network that uses VLANs
Configuring VLANs
To Configure Static VLANs
Vlan logical PPA = 1000 * VID + Device PPA
# ifconfig ce123000 plumb up # ifconfig ce224000 plumb up
# ifconfig -a
Page
Connectors
Table A-1SC Connector Link Characteristics Ieee P802.3z
Performance Specifications
Table A-2Cat-5 Connector Link Characteristics
Table A-3Performance Sepcifications
Physical Characteristics
Power Requirements
Table A-5Power Requirements
Page
Diagnostic Software Troubleshooting Issues
SunVTS Diagnostic Software
Reset the system
Using the OpenBoot Prom FCode Self- Test
Running the Ethernet FCode Self-Test Diagnostic
Shut down the system
Ok setenv diag-switch? false
Type show-netsto display the list of devices
Ok test /pci@1f,0/pci@1/network@4
Reset and reboot the system
Troubleshooting Issues
Set the auto-boot?configuration parameter to true
Ok setenv auto-boot? true
Type the following to apply and save your changes
Adv-pause-cap
Failure to Configure GigaSwift Ethernet Instance
Non-Specific Issues
Table B-1Troubleshooting the GigaSwift Ethernet Adapter
Add the following lines to the /etc/system file
Problem with DR Attach on Sun Enterprise Platforms
Reboot system
Set drdetachsafelist1=ce set hswpsuspendsafelist1=ce
Page
Symbols
Index