Remote Setup
You must enter the SETUP mode to program the remote control for the other components in your system, and to customize it for your conve- nience. There is only one way to enter the SETUP mode:
Hold down both the MAIN and ENT buttons for a few seconds until SETUP appears in the display.
The SETUP display shows 10 options. These are described in more detail as follows:
P-PRO
The remote is
to operate many types of equipment. The
1.Find the make of your TV, DVD, VCR, CD and other components, then look at the tables at the rear of this manual. Make a note of the various codes for each piece. Note that some TV/VCR combined units may use VCR codes, not TV.
2.Sit in a position in front of your equipment, and make sure that all components are turned off.
3.In the SETUP mode, press
4.Select the device button you want to program, then choose the de- vice table you took the code from. For example, for a TV, press TV twice. If you want AUX to control a VCR, press AUX, then press VCR.
5.You can now enter a code us-
ing the remote’s keypad, or UP or DOWN. After the third digit is entered, the remote transmits a power command. If the component turns on, press SAVE and then EXIT. Go to step 7.
User's Manual
6.If you could not fi nd a code which works, hold the UP button to step through all the codes in the table for that device. Release UP when your equipment turns on. If you go past, press DOWN. Press SAVE and then EXIT.
7.The display will change to show the devices again, still in the
8.Press MAIN to return to the main menu from any setup mode.
9.Test the remote to see which buttons will operate your equip- ment. For example, if you were trying to control your TV, check the power, channel up and down, and volume up and down. If some of these buttons are not working correctly, choose another code for that manufacturer, or you can learn over those not working by using the LEARN mode.
NOTE: If you accidently "learn over" one or more of the but-
tons which operate the TGIV, fear not. You can use ERASE (see page 28) to reset either the indi- vidual buttons, or the whole TGIV bank. After erasing, the buttons will revert to their TGIV programming.
FAV
This mode allows you to enter your favorite TV and radio stations.
Note that the following procedure assumes you have already pro- grammed your remote to operate your TV, radio tuner and other equipment. The keypad must already be able to select channels on your TV or SAT, and any TGIV tuner presets.
Before using FAV mode, use the EDIT mode to change the labels in the FAV display to show your station call signs or reminders. You can also delete the labels from unused buttons, or move all your most favorite FAV labels to page 1.
CHAPTER 3
1.In the SETUP mode, select FAV.
2.Select the device, such as
SAT, TV or TGIV, to learn station commands from.
3.The FAV display will appear, and you can step through fi ve pages using PAGE or FAV.
4.Press a favorite channel button and the fi rst character will blink. Use the keypad to enter the chan- nel number. For channels below 10, you should enter a 0 (zero)
fi rst. If you want, you can enter a power button before entering the channel. Also, if your equipment needs it, you may have to enter the ENT button after the channel is entered. If you want to add a short delay, press PAUSE (II).
5.When you have fi nished with one channel, press its button, and the label will reappear. Move on to the next favorite channel and program it in the same way. Repeat this for all the channels and devices. Press MAIN to return to the top menu.
6.Now, if you press the molded FAV button, the favorite channels ap- pear in the display, and the ones you programmed will take you to your favorite channel or radio sta- tion. If you programmed in a power command, the TV or tuner will turn on fi rst.
7.The commands are sent in se- quence, for example for channel 13, fi rst the 1 and then the 3 are sent. Wait a few seconds before switching between favorites, or your TV may receive for example, the 1 of one button and the 2 of the next.
continued..
27
