Power On LED, NMI Button | SUPER MICRO Computer 6015T-INF, 6015T-T

SUPERSERVER 6015T-T/6015T-INF User's Manual

Power On LED

The Power On LED connector is lo- cated on pins 15 and 16 of JF1. This connection is used to provide LED indication of power being supplied to the system. See the table on the right for pin deﬁ nitions.

NMI Button

The non-maskable interrupt button header is located on pins 19 and 20 of JF1. Refer to the table on the right for pin deﬁ nitions.

Power LED

Pin Deﬁnitions (JF1)

Pin# Deﬁ nition

155V Stby

16Control

NMI Button

Pin Deﬁnitions (JF1)

Pin# Deﬁ nition

19Control

20Ground

Fan Headers

The X7DBT-T/X7DBT-INF has four 6-pin proprietary fan headers. Each fan header supports two 3-pin fans. See the table on the right for pin deﬁ nitions. Note: The onboard fan speed is controlled by the CPU die temperature.

Chassis Intrusion

The Chassis Intrusion header is des- ignated JL1. See the board layout for the location of JL1 and the table on the right for pin deﬁ nitions.

Fan Header Pin Deﬁnitions

(Fan1/2 - Fan7/8)

Pin #	Deﬁ nition	Pin #	Deﬁ nition
1	PWR (DC		Ground
1	PWR (DC	4	Ground
	Speed CTRL)
2	Tachometer for		Tachometer for
2	Tachometer for	5	Tachometer for
	Fan 1/3/5		Fan 2/4/6
3	Ground		PWR (DC
3	Ground	6	PWR (DC
			Speed CTRL)

Chassis Intrusion

Pin Deﬁnitions (JL1)

Pin# Deﬁ nition

1Intrusion Input

2 Ground

5-14

Image 50

SUPER MICRO Computer 6015T-INF, 6015T-T manual Power On LED, NMI Button, Fan Headers, Chassis Intrusion

Contents

Super Manual Revision 1.0b Release Date April 7 Manual Organization PrefaceAbout This Manual Advanced Chassis Setup System SafetyAdvanced Serverboard Setup Bios Preface Table of Contents System Safety Advanced Serverboard Setup Advanced Chassis Setup Bios Appendices Page Chapter Introduction Overview Serial ATA Serverboard FeaturesProcessors Memory PCI Expansion Slots ATI Graphics Controller Other FeaturesOnboard Controllers/Ports ESB2 Server Chassis Features 1U Twin System Notes Sata Backplane/Drives Europe Contacting SupermicroHeadquarters Asia-PaciﬁcPage Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a RackInstalling the Inner Rails Installing the Outer Rails Locking Tabs Installing the Server into the Rack Installing the Server into a Telco Rack Installing the Server into a Rack Checking the Serverboard Setup Accessing the Inside of the System Check the Sata drives Checking the Drive Bay SetupSupplying power to the system Check the airﬂow Chapter System Interface Control Panel Buttons Control Panel LEDs Sata Drive Carrier LEDs Page Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Handling the Serverboard Chapter Advanced Serverboard SetupPrecautions Check compatibility of serverboard ports and I/O shield Serverboard InstallationUnpacking Mounting the serverboard onto the serverboard tray Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control Panel I/O Ports Processor and Heatsink Installation Installing the ProcessorPage Installing the Heatsink Removing the Heatsink Memory support Installing MemoryInstalling memory modules Bit PCI-X slot PCI card installationAdding PCI Cards Serverboard Details X7DBT-T/X7DBT-INF Layout Not drawn to scale LED Indicator Description Jumper Description Default SettingConnector Description X7DBT-T/X7DBT-INF Quick Reference Auxiliary Power Connector Connector DeﬁnitionsATX Power Connector Pwon Connector Overheat LED OH NIC2 LAN2 LED Fan Headers Power On LEDNMI Button Chassis Intrusion Wake-On-LAN Universal Serial Bus USBLAN1/2 Ethernet Ports Sgpio Header Wake-On-RingSerial Ports SMB Power I2C SMB Explanation Jumpers Jumper SettingsVGA Enable/Disable Cmos Clear I2C to PCI-Express Slot LAN1/LAN2 Enable/DisableWatch Dog Enable/Disable InﬁniBand LED Indicators LE2/ LE3 Onboard IndicatorsOnboard Power LED LE1 LAN1/LAN2 LEDs Tools Required Chapter Advanced Chassis SetupStatic-Sensitive Devices Control Panel Chassis Front View Sata Drive Installation Drive Bay Installation/RemovalAccessing the Drive Bays System Fans Removing a Sata Drive Replacing the Power Supply Power SupplyPower Supply Failure Removing the power supply Removing the Power Supply Starting the Setup Utility System BiosHow To Change the Conﬁguration Data Chapter Press the Delete key to enter Setup Running SetupMain Bios Setup System Time Main Bios Setup Menu Main Setup FeaturesBios Date System Date Multi-Sector Transfers LBA Mode ControlType Native Mode Operation Transfer ModeUltra DMA Mode Sata Controller Mode Extended Memory Sata Ahci Available when Sata RAID is DisabledSystem Memory QuickBoot Mode Advanced SetupBoot Features QuietBoot Mode Power Loss Control Acpi ModePower Button Behavior Memory Cache Cache System Bios Area Cache Extended Memory Cache Base 0-512KCache Base 512K-640K Discrete Mtrr Allocation PCI Parity Error Forwarding Default Primary Video AdapterEmulated IRQ Solutions Reset Conﬁguration Data Large Disk Access Mode Enable MasterLatency Timer Serr Signal Condition Branch 0/1 Rank Interleaving Memory Branch ModeHigh Temperature Dram Operation Branch 0/1 Rank Sparing Enabling Multi-Media Timer Crystal Beach FeaturesClock Spectrum Feature Snoop Filter Advanced Processor Options CPU Speed DCA Delay Clocks Available when supported by the CPU Hardware Prefetch Available when supported by the CPUDirect Cache Access Available when supported by the CPU Intel Eist Support Available when supported by the CPU Mode Device ConﬁgurationSerial Port B Base I/O Address Baud Rate Console RedirectionCOM Port Address Console Type Voltage Monitoring CPU Temperature ThresholdHardware Monitor Logic Fan Speed Control Modes CPU Temperature Threshold See note on Temperature Monitoring Existing Event Log Number System Event LoggingClear System Event Logging Event Log Control Timer for Loading OS Minutes System Event Log/System Event Log List ModeOS Boot Watch Dog Time Out Option Realtime Sensor Data Set Supervisor Password Supervisor Password IsUser Password Is Set User Password Boot Priority Order/Excluded from Boot Orders BootPassword on Boot Exit Appendix a Bios Post Messages Real time clock error System Cmos checksum bad Default conﬁguration usedSystem timer error Check date and time settings Allocation Error for device System cache error Cache disabledFail-Safe Timer NMI Failed Entering Setup Device IRQ conﬂict PS/2 Mouse Boot Summary ScreenInvalid System Conﬁguration Data Nnnn kB Extended RAM Passed System Bios shadowed Press F1 to resume, F2 to Setup, F3 for previousPress F2 to enter Setup Video Bios shadowedPage Terminal Post Errors Appendix B Bios Post CodesRecoverable Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for the boot block in Flash ROM Page Important Notes to the User Intel HostRAID Setup GuidelinesIntroduction to Serial ATA and Parallel ATA Serial ATA Sata Intel HostRAID Conﬁgurations Intel Matrix Storage Using the Intel ESB2 Sata RAID Utility Program Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting a RAID Volume Resetting to Non-RAID and Resetting a RAID HDD Exiting the Intel Matrix Storage Manager Utility Installing Windows XP/2000/2003 for RAID Systems Appendix D System Speciﬁcations Chassis WeightPower Supply System Cooling Regulatory Compliance