ATA Conﬁguration | SUPER MICRO Computer AS1020S-8 manual

AS1020S-8 User's Manual

S-ATA Conﬁguration

HT1000 S-ATA

Use this setting to Enable or Disable the on-chip SATA controller.

S-ATA Mode

Use this select either IDE or MMIO as the SATA mode.

HT1000 SATA HostRaid Support

This setting is used to Enable or Disable the SATA Host RAID.

ACPI Conﬁguration

Advanced ACPI Conﬁguration

ACPI Version Features

Select which version of ACPI you wish to use. Options are ACPI v. 1.0, ACPI v. 2.0 and ACPI v. 3.0.

ACPI APIC Support

Select "Enabled" to allow the ACPI APIC Table Pointer to be included in the RSDT pointer list. The options are Enabled and Disabled.

ACPI OEMB Table

This setting when enabled will include an OEMB table pointer to pointer lists. Options are Enabled and Disabled.

Headless Mode

Select "Enabled" to activate the Headless Operation Mode through ACPI. The options are Enabled and Disabled.

Event Log Conﬁguration

View Event Log

Highlight this item and press <Enter> to view the contents of the event log.

Mark All Events as Read

Highlight this item and press <Enter> to mark the DMI events as read.

7-10

Image 80

SUPER MICRO Computer AS1020S-8 ATA Conﬁguration, Acpi Conﬁguration Advanced Acpi Conﬁguration, Event Log Conﬁguration

Contents

AS1020S-8 Manual Revision Release Date December 28 Manual Organization PrefaceAbout This Manual System Safety Advanced Serverboard SetupAdvanced Chassis Setup Bios Preface Table of Contents Advanced Serverboard Setup HDD LED NIC1 LED NIC2 LED Advanced Chassis Setup Jsled Bios AppendicesPage Chapter Introduction Overview Serverboard Features Server Chassis Features Cooling System Serverworks HT-2000/1000 Chipset System Block Diagram Page Unpacking the System Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Rack Mounting Considerations Identifying the Sections of the Rails Installing the System into a RackInstalling the Rack Rails Installing the Chassis Rails Identifying the Sections of the Rails Installing the Server into the Rack Installing the Server into a Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Checking the Serverboard Setup Checking the Drive Bay Setup Accessing the drive baysCD-ROM and ﬂoppy disk drives Check the Scsi disk drives Supplying power to the system Check the airﬂow Chapter System Interface Control Panel Buttons Control Panel LEDs Scsi Drive Carrier LEDs Page Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Chapter Advanced Serverboard Setup PrecautionsHandling the Serverboard Unpacking Mounting the Serverboard into a Chassis Processor and Heatsink InstallationInstalling the Processor install to the CPU#1 socket ﬁrst Page Installing the Heatsinks Installing Heatsinks Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control Panel I/O Ports Installing Memory Support Side and Top Views of DDR Installation Optimizing memory performance PCI slots PCI card installationAdding PCI Cards Serverboard Details H8DSR-8 Serverboard Layout Not drawn to scale Jumpers Description Default Setting Connectors DescriptionH8DSR-8 Quick Reference Onboard LEDs Description Connector Deﬁnitions Primary ATX Power ConnectorProcessor Power Connector Secondary Power Connection Power LED Overheat/Fan Fail LED Power Fail LED Reset ButtonPower Button USB0/1 Universal Serial Bus Ports USB2/3 Headers Serial PortsFan Headers ATX PS/2 Keyboard and PS/2 Mouse Ports Power LED/Speaker SMB Power I2CJLAN1/2 Ethernet Ports Ipmb Header Overheat LED Wake-On-RingWake-On-LAN Chassis Intrusion Cmos Clear Jumper SettingsExplanation Jumpers Watch Dog Onboard Speaker Enable/ DisablePCI-X Slot Frequency Select Scsi Controller Enable/ Disable Scsi Termination Enable/ DisableVGA Enable/Disable Power Force On Onboard Indicators I2C to PCI Enable/Disable+3.3V Power LED JLAN1/JLAN2 LEDs Scsi Activity LEDs Post Code LEDs Floppy Connector Floppy, IDE and Scsi Drive Connections IDE Connector Scsi Connectors Diffsens TermpwrPage Tools Required Chapter Advanced Chassis SetupStatic-Sensitive Devices Control Panel Chassis Front and Rear Views Installing a new fan System FansSystem Fan Failure Replacing System Fans Drive Bay Installation/Removal Accessing the Drive Bays Scsi Drive Installation Mounting a Scsi drive in a drive carrier Installing/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation Power Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supply Removing/Replacing the Power Supply Page Introduction Starting the Setup UtilityChapter CPU Conﬁguration Sub-Menu Advanced Settings MenuMain Menu IDE Conﬁguration DMA Mode A.R.TBit Data Transfer Hard Disk Write Protect PCI/PnP Menu Floppy Conﬁguration Super IO Conﬁguration Chipset Menu North Bridge Conﬁguration MCT Timing Mode User Conﬁguration ModeEnable Clock to All DIMMs ECC Conﬁguration Dram ECC Enable Power Down Control ECC Chip KillDram Scrub Redirect Dram BG Scrub Event Log Conﬁguration ATA ConﬁgurationAcpi Conﬁguration Advanced Acpi Conﬁguration Hyper Transport Conﬁguration AMD PowerNow Conﬁguration Remote Access ConﬁgurationMPS Conﬁguration PCI Express Conﬁguration CPU Overheat Temperature System Health MonitorSystem Fan Monitor Fan Speed Control Modes Boot Menu Boot Settings Conﬁguration Boot Device Priority Hard Disk DrivesRemovable Drives CD/DVD Drives Security Menu Exit Menu Load Optimal Defaults Load Fail-Safe DefaultsPage Beep Code Error Message Description Appendix a Bios Error Beep CodesAmibios Error Beep Codes Page Appendix B Bios Post Checkpoint Codes Uncompressed Initialization Codes Bootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Appendix C System Speciﬁcations Weight Power SupplyServerboard Chassis Regulatory Compliance