Manuals / Brands / Kitchen Appliance / Refrigerator / Teledyne / Kitchen Appliance / Refrigerator

Teledyne 6712SR 7.2 Telephone Commands , Table 7-2 Serial Data Codes (Continued), Table 7-3 Remote Control of Sampler Keypad

1 224

Download 224 pages, 3.51 Mb

6712SR Refrigereated Sampler

Section 7 Remote Operation

7-7

7.1.3 Remote Control of

Sampler Keypad

To control the sampler keypad remotely, type CONTROL at the

“>” prompt and press ENTER. The sampler display is mirrored

on your computer monitor as you step through the programming

screens. While in this mode, the computer keys will be redirected

to simulate the sampler’s keypad, which will be disabled to avoid

any conflict. The active keys and their corresponding functions

are given in Table 7-3.

7.2 Telephone Commands 6712 controllers equipped with an internal voice modem can be

operated using telephone commands. This factory-installed

option includes a 12 ft (3.6 m) modem cable.

After connecting to the sampler from a touch-tone telephone,

command numbers may be entered from the telephone’s keypad,

followed by the (pound) button. The commands are listed in

Table 7-4.

To use telephone commands:

1. Dial the sampler’s telephone number. When the sampler

connects, it answers with “Teledyne Isco Sampler Site

[number].” If the sampler does not receive a touch-tone

command in five seconds, it assumes that a computer

modem has called and initiates the modem connect

sequence. If this occurs you must hang up and try again.

2. Enter the command. For example, to run program 1, press

.

xxD_ 4, 5 Other data not listed above

1The three most recent samples will have entries as B?. The “?” will be

the first bottle number in the set. If the sample is a grab sample, it will

be shown as B0.

2Rainfall tips roll over every 256 counts.

3The checksum does not include the checksum, carriage return, and

linefeed. The string is terminated with <CR><LF>.

4A “_” in the identifier indicates an SDI-12 address.

5“XX” matches the data label for the SDI-12 parameter.

Table 7-2 Serial Data Codes (Continued)

Identifier Parameter Units

Table 7-3 Remote Control of Sampler Keypad

Computer Sampler

<Esc>, S, s STOP

L,l,U,u, <Backspace> Left / Up

R, r, D, d Right / Down

O, o ON

<Enter>, arrows, decimal, numbers Same

You will not be able to turn the sampler off remotely.

#

1 #

Contents

Main Page Foreword Page AVERTISSEMENT DANGE R Hazard Symbols v 6712SR Refrigerated Sampler Tabl e of Con ten ts Section 1 Introduction Section 2 Installation/Preparation Section 3 Getting Started Section 4 Standard Programming Section 5 E xtended Programming vii viii Section 6 SDI-12 Sondes Section 7 Remote Operation Appendix A Menu Flowcharts Section 8 Maintenance ix List of Illustrations 6712SR Refrigerated Sampler x List of Tables Page Page Section 1 Introduction 1.1 About This Manual 1.2 About 700 Series Modules 1.3 SDI-12 Sondes 1.4 Memory to Store Monitoring Data 1.5 Pump Requirements Table 1-1 6712SR Sampler Features G ENERAL F 1-4 1-5 SAMPLE DELIVERY SYSTEM FEATURES STANDARD PROGRAMMING FEATURES 1-6 E XTENDED P ROGRAMMING F 1-7 Table 1-2 6712SR Sampler Construction Materials Item Material Table 1-3 Technical Specifications for the 6712SR Refrigerated Sampler 6712 Controller, Pump, and Tubing: Mechanical Specifications 1-8 6712 Controller: Electrical Specifications 1-9 Power Consumption 1-10 6712 Controller: Software Specifications Page 1-12 locations where the refrigerators lower compartment could become submerged. 1-13 Table 1-4 Connector Specifications Connector Icon Pin Location Diagram Pin Function R AIN G AUGE 9-P IN F EMALE , S POWER SOURCE 2-PIN MALE, SEALED AGround INTERROGATOR 6-PIN FEMALE, SEALED ASwitched +12 volts DC Page Section 2 Installation/Preparation 2.1 Preparing the Sampler Page Table 2-1 Distributor Arm Positions and Discharge Tube Lengths for Bottle Kits 2.2 Installing Bottle Kits NEVER MANUALLY ROTATE THE DISTRIBUTOR ARM. NEVER MANUALLY ROTATE THE DISTRIBUTOR ARM. 2.3 Suction Line 2.4 Strainers 2.5 How Does the Sampler Work? Table 2-2 Selecting the Right Strainer Page 2.6 Installing the Sampler 2.7 Connecting External Instruments Table 2-3 Connecting Teledyne Isco Instruments to the Sampler 2.8 Locking the Sampler 2.9 Servicing the Sampler Page Section 3 Getting Started 3.1 Initial Operation Table 3-1 About the Keypad 3.2 Using Menus and Entering Numbers 3.3 Quick View Screens 3.4 Clock and Calendar Page 3.5 Menu Screens: Site Descriptions and Program Names 3.6 Messages Page 3.7 Menu Trees Section 3 Getting Started 3-11 Figure 3-1 Menu Tree for Standard Programming Page Section 4 Standard Programming 4.1 Switching Between Standard and Extended Modes 4.2 Language Selection, Units of Length 4.3 Programming Examples Table 4-1 Standard Program: Sample Every 15 Minutes, One Sample Per Bottle Table 4-1 Standard Program: Sample Every 15 Minutes, One Sample Per Bottle (Continued) Table 4-2 Standard Program: Flow-Paced Sampling, Two Bottles Per Sample Table 4-2 Standard Program: Flow-Paced Sampling, Two Bottles Per Sample (Continued) 4.4 Pacing 4.5 Distribution 4-7 Figure 4-1 Sample Distribution Sequential Each bottle receives a sample from multiple sample events. Multiple bottles receive a sample from one sample event. 4.6 Start Times Page 4.7 Running Programs Page 4.8 Interrupting a Running Program Page 4.9 Other Functions 4.10 Manual Functions 4.11 Grab Samples 4.12 Calibrate Volume 4.13 Operating the Pump 4.14 Moving the Distributor Arm 4.15 Reports Page Page 4-22 Table 4-3 Reports: Program Events, Source Codes, and Error Codes Program Events Table 4-3 Reports: Program Events, Source Codes, and Error Codes (Continued) 4-23 Source Codes Error Codes Page Page Page Page 4-28 Figure 4-9 Report: Summary 4.16 System IDs 4.17 Programming for 700 Series Modules Table 4-4 Programming Example With 730 Module Installed Page Table 4-4 Programming Example With 730 Module Installed (Continued) 4-32 Table 4-5 Programming Example With 750 Module Installed Table 4-5 Programming Example With 750 Module Installed (Continued) Section 5 Extended Programming 5.1 Extended and Standard Mode 5.2 One-Part and Two-Part Programs 5.3 Storage for Extended Programs Table 5-1 Selecting a Stored Extended Program 5.4 Programming for 700 series Modules 5.5 Programming SDI-12 Sondes 5.6 Programming Examples Page 5-6 Table 5-2 Storm Water Runoff Sampling 5-7 5-8 5-9 5-10 5-11 5.7 Suction Head 5.8 Rinses and Retries 5.9 Pacing Table 5-3 Event Paced Sampling Table 5-3 Event Paced Sampling (Continued) 5-14 Page 5.10 Distribution Page 5-18 Figure 5-1 Sample Distribution Sequential 8 7 5.11 Flow Proportional Sample Volumes Page Page 5.12 Sampler Enable Page 5-24 5.12.1 Sampler Enable Table 5-4 Sampler Enable 5.13 Sampler Enable Responses Page 5.14 Pauses/Resumes 5.15 Running Programs 5.16 Sampling Reports 5.17 Other Functions 5.18 Software Options Page Page Page Page 5-33 Table 5-5 Serial Data Codes Identifier Parameter Units Table 5-5 Serial Data Codes (Continued) 5.19 Hardware Setup From Standby While Running a Program Page Page Example: Dialout Alarms * Page 5.20 Memory 5.21 Pressurized Lines 5.22 Command Driven Operation 5.23 Command Driven Sampler Responses Page Section 6 SDI-12 Sondes 6.1 SDI-12 Data Parameters 6.2 Scanning For Sondes 6.3 Teledyne Isco Ready Sondes 6.4 Other SDI-12 Sondes 6.5 Sonde Setup - Storing Parameter Data 6.6 Sonde Calibration and Validation Page 6.7 Disconnecting Sondes Page 6712SR Refrigereated Sampler Section 7 Remote Operation 7.1 Computer Operation Table 7-1 6712 Remote Menu Commands Page Page Table 7-2 Serial Data Codes 6712SR Refrigereated Sampler Section 7 Remote Operation 7-6 Table 7-2 Serial Data Codes (Continued) Identifier Parameter Units 7.2 Telephone Commands Table 7-2 Serial Data Codes (Continued) 1 # Table 7-3 Remote Control of Sampler Keypad # Table 7-4 6712 Remote Commands 0 # 1 # 2# 3 # 4# 5 # 6 # 7 # Section 8 Maintenance 8.1 Maintenance Checklist 8.2 Cleaning Guidelines 8.3 Cleaning Protocols for Priority Pollutants Page 8.4 Maintenance Screens Table 8-1 Setting the Clock and Calendar Table 8-1 Setting the Clock and Calendar (Continued) Table 8-2 Resetting the Pump Counter Table 8-3 Checking and Replacing the Internal Battery Page 8.5 Replacing the Pump Tube Page Page 8.6 Opening the Controller Case 8.7 Replacing the Desiccant Page 8.8 Replacing the Internal Battery Page 8.9 Error Messages 8.10 Pump Tube Warning 8.11 Servicing the Refrigerator A-1 Appendix A Menu Flowcharts Figure A-1 6712 Menu Tree for Standard Programming A-2 Figure A-2 Standard Programming: Programming Screens See Figure A-3: Standard and Extended Programming: Start Times. Programming screens for a 700 Series module. Refer to Modules manual. Programming screens shown are for a 730 Bubbler Flow Module. Screens for other modules may vary. Notes A-3 Figure A-3 Standard and Extended Programming: Start Times A-4 Continued in Figure A-5. Figure A-4 Standard Programming: Quick View; Programming Screens Units Selected screens are for a 730 Bubbler Flow Module. Screens for other modules may vary. Programming screens for a 730 Series Module. Refer to Modules manual. A-5 Continued from Figure A-4. See Run Time Screens on page -10. Figure A-5 Standard Programming: Quick View; Start Times A-6 Figure A-6 View Report Note A-7 Figure A-7 Maintenance Screens See Note A. A-8 Figure A-8 Manual Functions Screens A-9 Figure A-9 Extended Programming: Programming Screens See Figure A-10. See Figure A-11. See Figure A-12. See Figure A-6. Programming screens for a 700 Series Module. Refer to the Modules manual. Units Selected screens are for a 730 Bubbler Flow Module. Screens for other modules may vary. A-10 Continued from Figure A-9. See Figure A-11. Figure A-10 Extended Programming: Equipment Setup A-11 Figure A-11 Extended Programming: Pacing and Distribution See Figure A-12: Event Conditions See Figure A-13. Continued from Figure A-10. A-12 Continued from Figure A-12. Figure A-12 Extended Programming: Event Conditions All valid event options will be shown. A-13 Notes See Note B A. All valid enable options will be shown. Enable options may include: B. YES = Latched or Stay Enabled NO = Repeatable Enable Continued from Figure A-11. Continued from Figure A-21. A-14 See Figure A-15. Figure A-14 Extended Programming: Quick View; Programming Screens See Figure A-16 See Figure A-17. Programming screens for a 700 Series Mod- ules. Refer to the Modules manual. A-15 Continued from Figure A-14. Figure A-15 Extended Programming: Quick View; Equipment Set-Up When Liquid Detector is on See Figure A-16. A-16 Figure A-16 Extended Programming: Quick View; Pacing and Distribution Continued from Figure A-15. See FigureA-17. A-17 Notes See Note B. A. All valid enable options will be shown. Enable options may include: B. YES = Latched or Stay Enabled NO = Repeatable Enable Continued from Figure A-16. Continued from Figure A-21. A-18 Figure A-18 Extended Programming: Normal View; Software Options A-19 Figure A-19 Extended Programming: Quick View; Software Options A-20 If scan finds sonde, see Figure A-24. See Note A. Notes A. <- denotes input signal. -> denotes output signal. A-21 See Figure A-24. See Note A. Notes A-22 Figure A-22 Analog and Dialout Screens See Figure A-21. A. Factory installed option. Requires B1 hardware or newer. Note A-23 Figure A-24 SDI-12 Sonde Screens Proceed to calibration/validation screens and rest of Hardware screens. Page Page Page Page Page water Appendix B Material Safety Data Sheets B-6 *Optional Indicating Silica Gel Material Safety Data Sheet Buffalo, NY 14224 Section 1 - Material Identification and Information Section 2 - Physical/Chemical Characteristics Section 3 - Fire and Explosion Hazard Data Appendix B Material Safety Data Sheets B-7 *Optional Indicating Silica Gel Section 5 - Health Hazard Data Section 6 - Control and Protective Measures Page Appendix C General Safety Procedures C.1 Hazards C.2 Planning C.3 Adverse Atmospheres C.4 Entering Manholes Page Page Page C-6 Table C-1 Hazardous Gases Table C-1 Hazardous Gases (Continued) C-7 Table C-1 Hazardous Gases (Continued) C-8 Page Page Page Page Page Page Page Page Appendix E Accessories List E.1 Order Information E.2 Samplers E.3 Bottle Kits E-2 E.4 Bottle Racks, Retaining Rings, Discharge Tubes, Distributor Arm E.5 Bulk Sets of Bottles with Lids E-3 E.6 Pump Tubes, Suction Line, Strainers E.7 Data Collection Devices and Cables E-4 E.8 12-Volt Power Sources E.9 Modules, Rain Gauges, & Interfacing Instruments E.10 SDI-12 Data Acquisition Connect Cables Page Page Index-1 Index A B C D L M N O P T V W Y Page ( Fax: Email: Teledyne Isco One Year Limited Factory Service Warranty *