Teledyne 6712SR 1-9, Power Consumption

6712SR Refrigerated Sampler

Section 1 Introduction

1-9

Sampler Power

Requirements:

Nominal: 12 volts DC supplied by the refrigerator

Operational: 11 to 13 Volts DC

Absolute Maximum: 14.4 Volts DC

Power Pac k Requ iremen ts:

Use only Teledyne Isco-made

power packs certified by UL. (P/N

60-1684-088)

120VAC ±12VAC, 60 Hz., 1.0 Amp.

Note: This is the only version certified by UL. The line cord (mains

connect cable) is the “Disconnect Device.”

Power Consumptiona

6712 Controller in Standby 10 mA

Average Current of Accessories

Controller Display Backlight 228 mA

701 pH Moduleb11 mA

710 Ultrasonic Moduleb11 mA

720 Submerged Probe Moduleb11 mA

730 Bubbler Moduleb

— at 2 ft of liquid level 24 mA

— at 10 ft of liquid level 31 mA

750 Area Velocity Moduleb12 mA

780 4-20 mA Moduleb10 mA

YSI 600 with pH, DO, Conductivity, and Temperatureb11 mA

Programmable Analog 4-20 mA Output Optionc124 mA

CDMA cellular telephone modem

— standby current 35 mA

— current while communicating 150 mA

GSM cellular telephone modem

— standby current 62 mA

— current while communicating 230 mA

a. Current ratings when input power is 12.5 VDC and ambient temperature is 77 °F (25 °C)

b. Average current when programmed to take readings at 15 minute intervals.

c. Rating for three outputs.

Sampler Only

Operating Current: Approximately 30 mA based on 200 ml sample every hour, 10 ft (3 m) suction

line, and 5 ft (1.5 m) suction head.

Teledyne Isco External Battery Capacity:Number of Complete Standard Sampling Routines

Nickel-Cadmium Battery Lead-Acid Battery

Sampler Only: 6 9

Sampler with pH Module: 6 9

Sampler with Ultrasonic Module: 6 9

Sampler with Submerged Probe Module: 6 9

Sampler with Bubbler Module (1-2 ft head): 3 5

Sampler with Area Velocity Module: 4 6

Sampler with 4-20 mA Module: 6 9

A Standard Sampling Routine is a 200 ml sample taken every hour in 24 bottle mode, with a 10 foot (3 m) vinyl suc-

tion line at 5 feet (1.5 m) of head. The module is set to take a reading every 15 minutes.

Flow Meter

Signal Requirement: 5 to 15 volt DC pulse or isolated contact closure of at least 25 millisecond dura-

tion. (4 - 20 mA or pulse duration signal may be converted with optional interface

unit.)

Table 1-3 Technical Specifications for the 6712SR Refrigerated Sampler (Continued)

Contents

Main Page Foreword Page AVERTISSEMENT DANGE R Hazard Symbols v 6712SR Refrigerated Sampler Tabl e of Con ten ts Section 1 Introduction Section 2 Installation/Preparation Section 3 Getting Started Section 4 Standard Programming Section 5 E xtended Programming vii viii Section 6 SDI-12 Sondes Section 7 Remote Operation Appendix A Menu Flowcharts Section 8 Maintenance ix List of Illustrations 6712SR Refrigerated Sampler x List of Tables Page Page Section 1 Introduction 1.1 About This Manual 1.2 About 700 Series Modules 1.3 SDI-12 Sondes 1.4 Memory to Store Monitoring Data 1.5 Pump Requirements Table 1-1 6712SR Sampler Features G ENERAL F 1-4 1-5 SAMPLE DELIVERY SYSTEM FEATURES STANDARD PROGRAMMING FEATURES 1-6 E XTENDED P ROGRAMMING F 1-7 Table 1-2 6712SR Sampler Construction Materials Item Material Table 1-3 Technical Specifications for the 6712SR Refrigerated Sampler 6712 Controller, Pump, and Tubing: Mechanical Specifications 1-8 6712 Controller: Electrical Specifications 1-9 Power Consumption 1-10 6712 Controller: Software Specifications Page 1-12 locations where the refrigerators lower compartment could become submerged. 1-13 Table 1-4 Connector Specifications Connector Icon Pin Location Diagram Pin Function R AIN G AUGE 9-P IN F EMALE , S POWER SOURCE 2-PIN MALE, SEALED AGround INTERROGATOR 6-PIN FEMALE, SEALED ASwitched +12 volts DC Page Section 2 Installation/Preparation 2.1 Preparing the Sampler Page Table 2-1 Distributor Arm Positions and Discharge Tube Lengths for Bottle Kits 2.2 Installing Bottle Kits NEVER MANUALLY ROTATE THE DISTRIBUTOR ARM. NEVER MANUALLY ROTATE THE DISTRIBUTOR ARM. 2.3 Suction Line 2.4 Strainers 2.5 How Does the Sampler Work? Table 2-2 Selecting the Right Strainer Page 2.6 Installing the Sampler 2.7 Connecting External Instruments Table 2-3 Connecting Teledyne Isco Instruments to the Sampler 2.8 Locking the Sampler 2.9 Servicing the Sampler Page Section 3 Getting Started 3.1 Initial Operation Table 3-1 About the Keypad 3.2 Using Menus and Entering Numbers 3.3 Quick View Screens 3.4 Clock and Calendar Page 3.5 Menu Screens: Site Descriptions and Program Names 3.6 Messages Page 3.7 Menu Trees Section 3 Getting Started 3-11 Figure 3-1 Menu Tree for Standard Programming Page Section 4 Standard Programming 4.1 Switching Between Standard and Extended Modes 4.2 Language Selection, Units of Length 4.3 Programming Examples Table 4-1 Standard Program: Sample Every 15 Minutes, One Sample Per Bottle Table 4-1 Standard Program: Sample Every 15 Minutes, One Sample Per Bottle (Continued) Table 4-2 Standard Program: Flow-Paced Sampling, Two Bottles Per Sample Table 4-2 Standard Program: Flow-Paced Sampling, Two Bottles Per Sample (Continued) 4.4 Pacing 4.5 Distribution 4-7 Figure 4-1 Sample Distribution Sequential Each bottle receives a sample from multiple sample events. Multiple bottles receive a sample from one sample event. 4.6 Start Times Page 4.7 Running Programs Page 4.8 Interrupting a Running Program Page 4.9 Other Functions 4.10 Manual Functions 4.11 Grab Samples 4.12 Calibrate Volume 4.13 Operating the Pump 4.14 Moving the Distributor Arm 4.15 Reports Page Page 4-22 Table 4-3 Reports: Program Events, Source Codes, and Error Codes Program Events Table 4-3 Reports: Program Events, Source Codes, and Error Codes (Continued) 4-23 Source Codes Error Codes Page Page Page Page 4-28 Figure 4-9 Report: Summary 4.16 System IDs 4.17 Programming for 700 Series Modules Table 4-4 Programming Example With 730 Module Installed Page Table 4-4 Programming Example With 730 Module Installed (Continued) 4-32 Table 4-5 Programming Example With 750 Module Installed Table 4-5 Programming Example With 750 Module Installed (Continued) Section 5 Extended Programming 5.1 Extended and Standard Mode 5.2 One-Part and Two-Part Programs 5.3 Storage for Extended Programs Table 5-1 Selecting a Stored Extended Program 5.4 Programming for 700 series Modules 5.5 Programming SDI-12 Sondes 5.6 Programming Examples Page 5-6 Table 5-2 Storm Water Runoff Sampling 5-7 5-8 5-9 5-10 5-11 5.7 Suction Head 5.8 Rinses and Retries 5.9 Pacing Table 5-3 Event Paced Sampling Table 5-3 Event Paced Sampling (Continued) 5-14 Page 5.10 Distribution Page 5-18 Figure 5-1 Sample Distribution Sequential 8 7 5.11 Flow Proportional Sample Volumes Page Page 5.12 Sampler Enable Page 5-24 5.12.1 Sampler Enable Table 5-4 Sampler Enable 5.13 Sampler Enable Responses Page 5.14 Pauses/Resumes 5.15 Running Programs 5.16 Sampling Reports 5.17 Other Functions 5.18 Software Options Page Page Page Page 5-33 Table 5-5 Serial Data Codes Identifier Parameter Units Table 5-5 Serial Data Codes (Continued) 5.19 Hardware Setup From Standby While Running a Program Page Page Example: Dialout Alarms * Page 5.20 Memory 5.21 Pressurized Lines 5.22 Command Driven Operation 5.23 Command Driven Sampler Responses Page Section 6 SDI-12 Sondes 6.1 SDI-12 Data Parameters 6.2 Scanning For Sondes 6.3 Teledyne Isco Ready Sondes 6.4 Other SDI-12 Sondes 6.5 Sonde Setup - Storing Parameter Data 6.6 Sonde Calibration and Validation Page 6.7 Disconnecting Sondes Page 6712SR Refrigereated Sampler Section 7 Remote Operation 7.1 Computer Operation Table 7-1 6712 Remote Menu Commands Page Page Table 7-2 Serial Data Codes 6712SR Refrigereated Sampler Section 7 Remote Operation 7-6 Table 7-2 Serial Data Codes (Continued) Identifier Parameter Units 7.2 Telephone Commands Table 7-2 Serial Data Codes (Continued) 1 # Table 7-3 Remote Control of Sampler Keypad # Table 7-4 6712 Remote Commands 0 # 1 # 2# 3 # 4# 5 # 6 # 7 # Section 8 Maintenance 8.1 Maintenance Checklist 8.2 Cleaning Guidelines 8.3 Cleaning Protocols for Priority Pollutants Page 8.4 Maintenance Screens Table 8-1 Setting the Clock and Calendar Table 8-1 Setting the Clock and Calendar (Continued) Table 8-2 Resetting the Pump Counter Table 8-3 Checking and Replacing the Internal Battery Page 8.5 Replacing the Pump Tube Page Page 8.6 Opening the Controller Case 8.7 Replacing the Desiccant Page 8.8 Replacing the Internal Battery Page 8.9 Error Messages 8.10 Pump Tube Warning 8.11 Servicing the Refrigerator A-1 Appendix A Menu Flowcharts Figure A-1 6712 Menu Tree for Standard Programming A-2 Figure A-2 Standard Programming: Programming Screens See Figure A-3: Standard and Extended Programming: Start Times. Programming screens for a 700 Series module. Refer to Modules manual. Programming screens shown are for a 730 Bubbler Flow Module. Screens for other modules may vary. Notes A-3 Figure A-3 Standard and Extended Programming: Start Times A-4 Continued in Figure A-5. Figure A-4 Standard Programming: Quick View; Programming Screens Units Selected screens are for a 730 Bubbler Flow Module. Screens for other modules may vary. Programming screens for a 730 Series Module. Refer to Modules manual. A-5 Continued from Figure A-4. See Run Time Screens on page -10. Figure A-5 Standard Programming: Quick View; Start Times A-6 Figure A-6 View Report Note A-7 Figure A-7 Maintenance Screens See Note A. A-8 Figure A-8 Manual Functions Screens A-9 Figure A-9 Extended Programming: Programming Screens See Figure A-10. See Figure A-11. See Figure A-12. See Figure A-6. Programming screens for a 700 Series Module. Refer to the Modules manual. Units Selected screens are for a 730 Bubbler Flow Module. Screens for other modules may vary. A-10 Continued from Figure A-9. See Figure A-11. Figure A-10 Extended Programming: Equipment Setup A-11 Figure A-11 Extended Programming: Pacing and Distribution See Figure A-12: Event Conditions See Figure A-13. Continued from Figure A-10. A-12 Continued from Figure A-12. Figure A-12 Extended Programming: Event Conditions All valid event options will be shown. A-13 Notes See Note B A. All valid enable options will be shown. Enable options may include: B. YES = Latched or Stay Enabled NO = Repeatable Enable Continued from Figure A-11. Continued from Figure A-21. A-14 See Figure A-15. Figure A-14 Extended Programming: Quick View; Programming Screens See Figure A-16 See Figure A-17. Programming screens for a 700 Series Mod- ules. Refer to the Modules manual. A-15 Continued from Figure A-14. Figure A-15 Extended Programming: Quick View; Equipment Set-Up When Liquid Detector is on See Figure A-16. A-16 Figure A-16 Extended Programming: Quick View; Pacing and Distribution Continued from Figure A-15. See FigureA-17. A-17 Notes See Note B. A. All valid enable options will be shown. Enable options may include: B. YES = Latched or Stay Enabled NO = Repeatable Enable Continued from Figure A-16. Continued from Figure A-21. A-18 Figure A-18 Extended Programming: Normal View; Software Options A-19 Figure A-19 Extended Programming: Quick View; Software Options A-20 If scan finds sonde, see Figure A-24. See Note A. Notes A. <- denotes input signal. -> denotes output signal. A-21 See Figure A-24. See Note A. Notes A-22 Figure A-22 Analog and Dialout Screens See Figure A-21. A. Factory installed option. Requires B1 hardware or newer. Note A-23 Figure A-24 SDI-12 Sonde Screens Proceed to calibration/validation screens and rest of Hardware screens. Page Page Page Page Page water Appendix B Material Safety Data Sheets B-6 *Optional Indicating Silica Gel Material Safety Data Sheet Buffalo, NY 14224 Section 1 - Material Identification and Information Section 2 - Physical/Chemical Characteristics Section 3 - Fire and Explosion Hazard Data Appendix B Material Safety Data Sheets B-7 *Optional Indicating Silica Gel Section 5 - Health Hazard Data Section 6 - Control and Protective Measures Page Appendix C General Safety Procedures C.1 Hazards C.2 Planning C.3 Adverse Atmospheres C.4 Entering Manholes Page Page Page C-6 Table C-1 Hazardous Gases Table C-1 Hazardous Gases (Continued) C-7 Table C-1 Hazardous Gases (Continued) C-8 Page Page Page Page Page Page Page Page Appendix E Accessories List E.1 Order Information E.2 Samplers E.3 Bottle Kits E-2 E.4 Bottle Racks, Retaining Rings, Discharge Tubes, Distributor Arm E.5 Bulk Sets of Bottles with Lids E-3 E.6 Pump Tubes, Suction Line, Strainers E.7 Data Collection Devices and Cables E-4 E.8 12-Volt Power Sources E.9 Modules, Rain Gauges, & Interfacing Instruments E.10 SDI-12 Data Acquisition Connect Cables Page Page Index-1 Index A B C D L M N O P T V W Y Page ( Fax: Email: Teledyne Isco One Year Limited Factory Service Warranty *