Trouble Shooting And Repair, Mounting Screws

Relay PCA 04523

Addendum to E-Series Operator Manuals

3. TROUBLE SHOOTING AND REPAIR

General Trouble shooting hints for the relay PCA are the same as described for the previous versions for the PCA. See Chapter 11 of your M100E/M200E/M400E operator’s manual for more information.

3.1.Removing / Replacing the Relay PCA from the Instrument

The Relay retainer plate installed on the 045230200 PCA (version with AC relays) covers the lower right mounting screw of the relay PCA. Therefore, when removing the relay PCA, the retainer plate must be removed first.

Mounting

Screws

AC Relay Retain Occludes

Mounting Screw on

P/N 045230200

Figure 3-1: Relay PCA 04523 Mounting Screw Locations

USER NOTES:

05118 Rev B3

Page 21

Image 21

Teledyne M100E manual Trouble Shooting And Repair, Removing / Replacing the Relay PCA from the Instrument, Mounting Screws

Contents

9480 CARROLL PARK DRIVE SAN DIEGO, CA USA Toll-free Phone Phone Fax TELEDYNE INSTRUMENTS ADVANCED POLLUTION INSTRUMENTATION T-APIEmail api-sales@teledyne.com Relay PCA P/N THIS PAGE INTENTIONALLY BLANK subassemblies while the unit is under power SAFETY MESSAGESContacting Teledyne Instruments’ Customer Service Department at or Relay PCA Addendum to E-Series Operator Manuals TABLE OF CONTENTS LIST OF FIGURESLIST OF TABLES Relay PCA Table 1-1 List of Analyzers Using New Relay PCA P/N04523 1. INTRODUCTION1.1. What’s the Same 1.2. What’s Different 1.3. Relay PCA Location and LayoutFigure 1-1 Relay PCA Layout P/N04523 1.3.1. Version Figure 1-3 Relay PCA P/N 045230100 with Safety Shield In Place1.3.2. Version Figure 1-2 Relay PCA P/N 045230200 with AC Relay Retainer In Place USER NOTES 2.1. Power Distribution 2. OPERATION AND CONFIGURATION2.1.1. AC Power Configuration Figure 2-1 Power Distribution Block Diagram IZS Permeation Tube Heater and O2 Sensor Connection optional Figure 2-2 Location of AC power Configuration Jumpers AC Power Configuration for Internal Pumps JP7 2.1.1.1. AC configuration - Internal Pump JP7Figure 2-3 Pump AC Power Jumpers JP7 110 VAC /115 VAC Table 2-2 Power Configuration for Standard AC Heaters JP2 2.1.1.2. AC Configuration - Standard Heaters JP2Figure 2-4 Typical Set Up of AC Heater Jumper Set JP2 1 to Table 2-3 Power Configuration for Optional AC Heaters JP6 2.1.1.3. AC Configuration -Heaters for Option Packages JP6Figure 2-5 Typical Set Up of AC Heater Jumper Set JP2 2.2. Valve Control 2.3. Status LEDs & Watch Dog Circuitry 2.3.1. Watchdog Indicator D1D1 RED Figure 2-6 Status LED Locations - Relay PCA 2.4. Heater Control Loop Figure 2-7 Heater Control Loop Block DiagramThemocouples MOTHER BOARD Table 2-4 Thermocouple Configuration Jumper JP5 Pin-Outs 2.4.1. Thermocouple Inputs and Configuration Jumper JP5Type J Compensation Type K Compensation INPUT TC1 J15 Figure 2-8 Thermocouple Configuration Jumper JP5 Pin-OutsOutput Scale Selector 7 Type J Compensation 8 DC Power Test Point and Wiring Color Code 2.5. DC Power Supply Test PointsTable 2-6 DC Power Supply Acceptable Levels FROM 3.1. Removing / Replacing the Relay PCA from the Instrument 3. TROUBLE SHOOTING AND REPAIRMounting Screws Figure 3-1 Relay PCA 04523 Mounting Screw Locations Table 4-2 List of Included Electronic Schematics 4. SCHEMATICS AND SPARE PARTS FOR RELAY PCA P/NList of Spare Parts DOCUMENT #

Teledyne M100E manual Trouble Shooting And Repair, Mounting Screws, User Notes, Relay PCA, Rev B3

Models: M200E and M400E M100E

3. TROUBLE SHOOTING AND REPAIR

3.1.Removing / Replacing the Relay PCA from the Instrument

Mounting

Figure 3-1: Relay PCA 04523 Mounting Screw Locations