Telenetics 2185 Function Switch Two

Telenetics 2185

3-4

Switch segments 1-6 to 1-8 are used to set the data rate on the 2185. See

Table 3-2 for information on setting these switches.

Function Switch Two

Function switch two is an eight-segment DIP switch used to set control-

signal contention, select synchronous or asynchronous data format,

select or bypass the retiming buffer, enable or disable anti-streaming, set

the clock signal routing, set main channel RTS on DCD transparent or

on, and set main channel inbound CTS transparent or on.

Table 3-2. Data Rate Selection

Using Switch Segments 1-6 to 1-8

Clock Data

Rate (bps) Set 1-6 to: Set 1-7 to: Set 1-8 to:

75 Up Up Up

1200 Up Up Down

2400 Up Down Up

4800 Up Down Down

7200 Down Up Up

9600 Down Up Down

14400 Down Down Up

19200 Down Down Down

Table 3-3. Function Switch Two Summary

Function

Switch

Switch

Position Function

2-1 Up

Down

Sets Control Signal Contention

Sets Data Contention

2-2 Up

Down

Sets synchronous data format

Sets asynchronous data format

2-3 Up

Down

Synchronous Data Retiming Buffer in circuit

Synchronous Data Retiming Buffer bypassed

2-4 Up

Down

Disables Anti-Streaming

Enables Anti-Streaming

2-5 and 2-6 See Table 3-4 These two switches work together to set Clock

Routing

Contents

Main Notice Warni ng Page Page Contents Chapter 1, Introduction Chapter 2, Installation Chapter 3, Operation and Configuration Page Chapter 1 Introduction 2185 FEATURES Data Interface Main Channel Broadcast Subchannel Contention Synchronous Data Retiming Buffer Anti-Streaming APPLICATIONS Port-Sharing Mode Figure 1-1. Port-Sharing Application Page Co-Located Terminals Figure 1-3. Co-Located Terminals Application Cascading the 2185 Page Page 1-9 SPECIFICATIONS Table 1-1 summarizes 2185 specifications. Table 1-1. 2185 Specifications Page Chapter 2 Installation CUSTOMER RESPONSIBILITIES SITE SELECTION AND PREPARATION UNPACKING Packing Materials Equipment Supplied Damage/Material Shortages INSTALLATION PROCEDURE Page Page Page Chapter 3 Operation and Configuration Page FUNCTION SWITCHES Function Switch One Table 3-1. Enabling/Disabling Subchannels 3-4 Function Switch Two Table 3-2. Data Rate Selection Using Switch Segments 1-6 to 1-8 Clock Data Rate (bps) Set 1-6 to: Set 1-7 to: Set 1-8 to: Table 3-3. Function Switch Two Summary Function Page Table 3-4. Clock Routing Configurations Page Page Page Page Page Page Page Function Switch Three LED INDICATORS CONFIGURATION EXAMPLES Table 3-5. DTE/DCE Optioning Digital Bridging Application Example Page Table 3-7. Switch Two 3-17 Table 3-6. Switch One Table 3-8. Switch Three Leased-Line Backup Application Example Page Table 3-9. Switch One 3-21 Table 3-10. Switch Two Table 3-11. Switch Three Page Table 3-12. Switch One Settings 2185 A 3-24 Table 3-13. Switch Two Settings 2185 A Table 3-14. Switch Three Settings 2185 A Table 3-15. Switch One Settings 2185 B 3-25 Table 3-16. Switch Two Settings 2185 B Switch Table 3-17. Switch Three Settings 2185 B Switch Setting Reason MAIN POWER CONNECTION Table 3-18. LED Status Indicator Functions Page Page Chapter 4 Operation and Configuration MAINTENANCE PHILOSOPHY Preventive Maintenance Corrective Maintenance Recovery from Anti-Streaming Alarm Condition RETURNING DEFECTIVE EQUIPMENT FOR REPAIR General Packing Information Installations in the USA Installations Outside the USA or Canada Page Chapter 5 Ordering Information Ordering Information Table 5-1. Telenetics Ordering Information Page Glossary-1 Glossary This glossary defines terms used in the 2185 Operator's Guide. Glossary-2 Glossary-3 Page INDEX-1 Index A C D E Page Index (continued)