Initial Equipment Set-Up, Unpacking | Telex TR-500/600C manual

Initial Equipment Set-Up

Unpacking

Unpack your RadioCom System. A system package should contain the following Items:

Contact the shipper or your dealer immediately if anything is damaged or missing. Fill out the regis- tration card and return it to Telex to properly regis- ter your unit.

Quantity	Descripton

1	BTR-500 or BTR-600C Base Station

1	TR-500 or TR-600C Beltpack

1	Wall Power Supply

2	Antennas (one Transmit and one Receive)

1	Interconnect Cable (9 pin to 9 pin)

2	Dummy Loads (3 pin XLR male)

1	Operating Instructions

1	Warranty and Registration Card

2	Plastic Screwdrivers

4	Rubber Feet

Antenna Information

Antenna Connection

The base station is supplied with two (2) antennas. One 1/2-wave antenna for Transmit and one 1/2-wave for Receive. The antennas have TNC male connectors.

The frequency range of the antennas should match the receiver and transmitter of the base station. Match the color code on the antenna with the color code on the base station.

Attach the receive 1/2-wave antenna to the antenna input receptacle labeled “Receive” on the right side of the rear panel. The antenna should be vertically aligned.

Figure 9

Attaching Receive 1/2-Wave Antenna

-7-

Image 10

Telex BTR-500/600C operating instructions Initial Equipment Set-Up, Unpacking, Antenna Connection, Quantity Descripton

Contents

Telex Table of Contents Customer Service Information FCC Information Introduction System FeaturesGeneral Description Base Station Transceiver Front Panel Controls and Connections Base Station Intercom 1 and 2 Jacks Switch set to TelexIntercom 1 and 2 Jacks Switch set to RTS Controls and Connections Rear Panel BTR-600C BTR-500/600C Specifications Auxiliary Jack Beltpack Headset Jack WiringControls and Connections Beltpack Specifications Antenna Connection Initial Equipment Set-UpUnpacking Quantity Descripton Antenna Polarization Antenna PlacementDistance between Antennas Operating System Near Obstructions Distance Between base station BeltpackKeeping Site Clear to Antenna Antenna Placement Improving Reception and Increasing Range Location RF Transmit/Receive Channel SwitchesBase Station Set-Up Rack Mounting Intercom Type Switch RF Transmit Mode SwitchDual Listen Switches Auxiliary to I/C Switch Program Audio Audio Channel SwitchTelex IN/OUT Switch Auxiliary Switch Auxiliary to I/C Switch Interconnection to a Hard-Wired Intercom SystemConnecting Base Stations Together Example Interface to an Audiocom Telex Intercom System Intercom User Station US-2000A Program Speakers Intercom Power Supply PS15 Example Interface to an RTS Intercom System Auxiliary Audio Connection Power ConnectionDummy Load RF Channel Switches and RF Transmit Mode Code Switch TR-600C OnlyConnecting Headset Beltpack Set-Up Battery Installation Battery Installation Pre-Walk-Thru Checklist Local Headset Volume PowerPush-to-Talk/Lock-to-Talk Switch System Operation Auxiliary Level Dual Listen LevelIntercom Level Sidetone Level Beltpack Operation Power/Local Headset VolumeBattery Check Push-to-Talk/Lock-to-Talk Microphone Gain Sidetone Level Control Example System Configurations Single Base Station Audiocom Telex System Curtain Director RTS Power Supply Single Base Station RTS System Six Base Station RTS System Example of Six BTR-500 RTS Systems used by a Production Unit Eight Base Station Telex System = Beltpack Position 1 *2 = Beltpack Position Single Beltpack to Single Beltpack System Beltpack to Beltpack SystemExample of a TR-500 System used at a Publishing Firm System Walk-Thru Troubleshooting Tech Tips Codes Settings and the BTR600CFrequency Interaction Battery Information Intercom Systems Specifications Accessories and Replacement Parts Customer Service Information FCC Information JAN Made in U.S.A