Toshiba 203S, 203SD 1, 2

74

TONER CARTRIDGE REPLACEMENT

When toner is low, the error indicator will light up and "TONER CARTRIDGE IS

NEAR EMPTY." will appear in the display to alert you to purchase a new toner

cartridge. If copying is continued while the indicator is lit, copies will gradually

become lighter until the toner runs out. When the toner runs out, the machine will

stop operating, the error indicator will blink, and "REPLACE THE TONER

CARTRIDGE" will appear in the display. Follow the procedure below to replace the

toner cartridge.

1Open the bypass tray, and

then open the side cover

while pressing the side

cover open button.

2Push gently on both sides of

the front cover to open the

cover.

• After the machine stops, it may be possible to make a few more

copies by taking the toner cartridge out of the machine, shaking it

horizontally, then reinstalling it. If copying is not possible after this

operation, replace the toner cartridge.

• During a long copy run of a dark original, "TONER

REPLENISHMENT IN PROGRESS" appears in the display, and the

machine may stop even though toner is left. The machine will feed

toner up to 2 minutes and then the ready indicator will light up. Press

the [START] key ( ) to resume copying.

Note

Contents

Main For users in the USA FOR YOUR RECORDS ... Model Number Serial Number Date of Purchase Authorized Toshiba Copier Service Department Number NOTICE CONTENTS 1PREPARATIONS 2LOADING PAPER 3MAKING COPIES 4CONVENIENT COPY FUNCTIONS 6PRINTER/SCANNER FUNCTIONS 7USER SETTINGS 8TROUBLESHOOTING AND MAINTENANCE 9OPTIONAL EQUIPMENT 10 APPENDIX 3 CAUTIONS (10 cm) Caution label on the machine Cautions on using the machine 4 Cautions on handling the machine Trademark acknowledgements SOFTWARE LICENSE ENVIRONMENTAL INFORMATION SAFETY PRECAUTIONS 6 INTRODUCTION Using the manual About the operation manuals Operation Manual (this manual) 7 MAIN FEATURES A Sort copy Offset function 2 IN 1 copy Margin shift Page 9 1 PREPARATIONS This chapter provides basic information that you should know before using the machine. PART NA MES Operation panel e-STUDIO203S READY TO COPY. 100% 8.5x11 0 Display 12 POWER ON AND OFF The main screen of copy mode appears. Power on Turn the power switch to the "ON" position. Power off Power save modes Preheat mode Auto power shut-off mode 14 LOADING PAPER PAP ER For best results, use only TOSHIBA recommended paper. LOADING PAPER 15 1 and pull the paper tray out until it stops. 2 3 17 BYPASS FEED (including special paper) Important points when inserting paper in the bypass tray Envelopes Available Not Available 1 2 3 19 CHANGING A TRAY'S PAPER SIZE SETTING 1 2 3 4 20 MAKING COPIES NORMAL COPYING 1 2 3 1 up. 2 Check RADF open function 1 glass. 2 of the originals. 3 4 MAKING COPIES 23 Paper output tray extension Paper holder arm Setting the number of copies SELECTING THE TRAY 1 2 3 4 5 25 REDUCTION/ENLARGEMENT/ZOOM 1 2 3 ( ) to select the desired copy ratio and then press the [ENTER] key. 4 then press the [START] key ( ). 26 CONVENIENT COPY FUNCTIONS Using the document glass (e-STUDIO203SD only) 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 6 1 2 3 4 31 COPYING MULTIPLE ORIGINALS ONTO A SINGLE SHEET OF PAPER 1 2 3 4 5 6 1 2 3 4 5 34 1 2 "MARGIN SHIFT" appears and then press the [ENTER] key. Page 36 Chapter 5 INSTALLING THE SOFTWARE SOFTWARE MFP driver Printer driver Scanner driver 37 BEFORE INSTALLATION Hardware and software requirements 38 INSTALLING THE SOFTWARE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 INSTALLING THE SOFTWARE Connecting a USB cable 1 connector on the machine. 2 Page 5 6 7 8 Page 5 6 7 Page 6 7 8 49 Chapter 6 System requirements for USB 2.0 (Hi-Speed mode) PRINTER/SCANNER FUNCTIONS 50 USING THE PRINTER MODE BASIC PROCEDURE FOR PRINTING 1 2 3 4 Canceling a print job 1 2 51 USING THE SCANNER MODE SCANNING USING THE KEYS ON THE MACHINE 1 2 3 4 PRINTER/SCANNER FUNCTIONS 52 Button Manager scan menu SCANNING FROM YOUR COMPUTER OPERATION IN COPY, PRINTER, AND SCANNER MODES 53 1 2 3 4 5 Viewing the online manual 54 USER SETTINGS USER PROGRAMS Copy mode Page Page Page Print mode 59 SELECTING A SETTING FOR A USER PROGRAM 1 2 3 4 Audible signals (key entry beep, invalid key beep, base setting beep) Base settings 61 Chapter 8 DISPLAY MESSAGES TROUBLESHOOTING AND MAINTENANCE Indication Cause and remedy Page Lamp indicator Display 63 TROUBLESHOOTING THE MACHINE Page Page Page 67 PROBLEMS DURING SETUP OF THE SOFTWARE MFP driver cannot be installed (Windows 2000/XP) 1 2 3 4 Plug and play screen does not appear 1 2 3 4 The MFP driver cannot be correctly installed by Plug and Play (Windows 2000/XP/Vista) 1 2 3 4 Removing the software 1 2 3 70 MISFEED REMOVAL 1 2 A: Misfeed in the paper feed area 1 2 B: Misfeed in the fusing area 1 2 3 C: Misfeed in the transport area 1 2 3 4 D: Misfeed in the RADF (Option) Document feeder cover RADF jam release lever Roller (X) (Y) 74 1 2 3 4 5 76 6 7 SCAN HEAD LOCKING SWITCH 77 CHECKING THE TOTAL COUNT 1 Press the [ ] key ( ) or [ ] key ( ) until "TOTAL COUNT" appears, and then press the [ENTER] key. 2 display the count of each function. MAINTENANCE REQUIRED 78 CLEANING THE MACHINE Cabinet Document glass and the back side of the document cover/ RADF Document glass/scanning window Document cover/RADF RADF roller RADF scanning window Black line Page OPTIONAL EQUIPMENT 81 250-SHEET PAPER FEED UNIT (MY-1034) Using the MY-1034 with the printer function 1 2 3 4 5 Interface cable 82 APPENDIX Page Printer Function Scanner Function Reversing automatic document feeder (MR-2019) 250-sheet paper feed unit (MY-1034) 87 INDEX Symbols Numerics A M N O P R U INDEX BY PURPOSE Making copies Using convenient copy functions Connecting the computer Caution Page For users in the USA WARNING: Notice for Users in U.S.A. Declaration of Conformity