VCR code testing, Confirming your settings | Toshiba 51H93 guide

Chapter 5: Quick Connect Guide & TV Guide On Screen setup

Setting up the TV Guide On Screen system (continued)

3.Select your VCR brand, and then press ENTER. Code testing begins.

VCR code testing

1.To allow the TV Guide On Screen system to find the correct code for your brand of VCR, tune your VCR to channel 02, turn the VCR OFF, leave the TV ON, and then press ENTER.

The TV Guide On Screen system will test the code for the brand of VCR you selected. Do not press any keys on the TV, remote control, or VCR until testing is done.

2.When code testing is done, if your VCR tuned itself to channel 09, select YES and press ENTER. Go to “Confirming your settings” (next column on this page).

If your VCR did not tune itself to channel 09 and you want to test the same code again, select TEST THIS CODE AGAIN and press ENTER.

If your VCR did not tune itself to channel 09 and you want the TV Guide

On Screen system to search for the correct code, select NO and press ENTER. Go to step 3.

3.If the correct code is not found, the following screens appear, with helpful hints for finding the code.

Confirming your settings

1.Review the setup information displayed on your TV screen (an example is shown below).

If the information on your TV screen is correct for your setup, select YES, END THE SETUP PROCESS and press

ENTER.

If the information is incorrect, select NO, REPEAT THE SETUP PROCESS and press ENTER to repeat the TV Guide On Screen program guide setup process.

Note: If you skipped either the Cable box or VCR setup, the setup confirmation screen (below) will list INCOMPLETE for any information it has not received.

2. If you selected YES in step 1, the following screens appear.

Press ENTER to exit the TV Guide On Screen setup.

See ÒImportant final setup steps,Ó next page.

If you are using the Quick Connect Guide, go to the next page to complete the assisted setup.

Copyright © 2003 TOSHIBA CORPORATION. All rights reserved.	39

Image 39

Toshiba 51H93 owner manual VCR code testing, Confirming your settings, See ÒImportant final setup steps,Ó next

Contents

51H93 57H93 65H93 Tune Into Safety Safety PrecautionsIt Makes a Difference Where Your TV Stands Issue Important Safety Instructions Installation, Care, and ServiceAlways place the TV on the floor TV, follow these recommendations and precautions When the unit is being turned on orOr continuous, unplug the power cord Contact a Toshiba Authorized Service Center Contents Contents from previous Introduction Features of your new TVInstalling, setting up Using your new Demo TV back panel Connecting your TV TV front panel controls and connections4 5 6 7 8 For an explanation of cable types, see TV back panel connections Overview of cable types From Cable TV or antenna You will needTwo coaxial cables To view the VCR Select the Video 1 video input source Connecting a VCR and Cable boxVCR’s audio out jack using the white audio cable only To view basic and premium Cable channels To view the VCR or view and record antenna channels Connecting a VCR and satellite receiver To view the DVD player Connecting a DVD player with S-video and a VCRTo view basic channels and access the TV’s features To view premium Cable channels To record a TV program while watching a DVD Connecting a DVD player with component video and a VCROne set of component video cables Source on the TV You will need One set of standard A/V cables Connecting two VCRsConnecting a VCR to the REC OUT jacks To view VCR Select the Video 3 video input source Connecting a DVI/HDCP deviceConnecting a camcorder To view the camcorder video One optical audio cable Connecting a digital audio systemConnecting an analog audio system Highlight Audio Setup and press Enter Connecting an A/V receiver Dolby Pro Logic surround soundSystem connection example To control the devices Are on-screen. To access other deviceTheaterNet on-screen device control To connect the IR blaster cable Using TheaterNet on-screen device control Connecting IEEE-1394 Firewire video devicesUsing analog-compatible IEEE-1394 devices Supported signals IEEE-1394 device initialization IEEE-1394 device managementTo edit the IEEE-1394 device information Hub connection IEEE-1394 device interconnectionChain connection Hub connection Link connection To connect to the G-LINK jackSee Using the remote control Learning about the remote controlChannel Numbers 0-9, 100 directly access channels Installing the remote control batteries To install the remote control batteriesDevice mode control after programming Remote Control functional key chart CBL/SAT Audio VCR CH RTN Searching and sampling the code of a device Device code setupPress Mode to select the TV mode to control the TV Press Mode to select the mode you want to set up To reset the volume controls to the original device mode Using the volume lock featureOperational feature reset Repeatedly press Mode to select CABLE/SAT mode Multi-brand remote control device codes VCRsCable boxes Laser disks CD playersReceivers Cassette players Main menu layout Menu layout and navigation To close a menu instantly, press Exit Setup / Installation menu layoutNavigating the menu system Press Menu to open the menu system Selecting the menu language Starting the Quick Connect Guide assisted setupManually starting the Quick Connect Guide assisted setup If you already set up the TV Guide On Screen system, go to Following screen opens. Press Enter to continue Setting up the TV Guide On Screen systemConfiguring the location of your TV Configuring your Cable setup For G-LINK connection details, see Cable box code testingConfiguring your VCR setup Do you have a VCR? Select YES or NO, and then press VCR code testing Confirming your settingsSee ÒImportant final setup steps,Ó next Important final setup steps Completing the Quick Connect Guide assisted setup Selecting the menu language Setting up your TVConfiguring the antenna input sources To configure the ANT 1 and ANT 2 input sources Programming channels into the TV’s channel memory Programming channels automaticallyTo program channels automatically Manually adding and deleting channels in the channel memory To add and delete channels in the Favorite Channels lists To clear your favorite channel listsTo tune your favorite channels To remove a device from TheaterNet Setting up and using TheaterNet on-screen device controlSetting up TheaterNet To set up TheaterNet device control To view another source Using the TheaterNet control iconsTo close the on-screen control icons Press Exit Miscellaneous audio devices TheaterNet IR device codesAmplifiers Laser disk players ADC Video accessory Hdtv decoder Receivers STS Convergence using TouchFocus Adjusting the color convergenceManually adjusting the color Automatically adjusting the color To set the time and date Setting the time and date Checking system status Viewing the digital signal meter Skip these steps and go to the next TV Guide On Screen system includes the following features Action buttons About the TV Guide On Screen menu screensPanel ad Channel Blue and Green Windows Navigating the TV Guide On Screen system Channel surfing Listings menuViewing program listings and descriptions Info windows One-touch and VCR Plus+ recording Direct tuningSetting programs as favorites Video Window To open the Sort menu Using the Menu Bar to access other menusSort menu Viewing panel ads and channel ads Schedule menu Setup menuChange system settings Review options change the auto display setting Troubleshooting Promotions menuMessages menu Using the TV’s features Using the digital tuner holdSelecting the video input source to view To label the video input sources To clear the video labels Labeling the video input sources Using SpeedSurf to change to a specific programmed channel Tuning channelsTuning to the next programmed channel Switching between two channels using Channel Return To select the picture size Press PIC Size on the remote controlSelecting the picture size Natural picture size Full picture size Theater Wide 1 picture sizeTheater Wide 2 picture size Theater Wide 3 picture size Using the auto aspect ratio feature 480i signals only To turn on the Auto Aspect featureTo turn off the Auto Aspect feature To select the display format Selecting the cinema modeTo set the Cinema Mode to Film To set the Cinema Mode to Video To close the POP window Using the POP featuresUsing the POP double-window feature To display a program in the POP window To close the still POP window Switching the main and POP picturesAdjusting the size of the main and POP pictures Freezing the main picture in the POP double-window To scan the programmed channels Using the programmed channel scan featureTo cancel the channel scan without changing the channel POP double-window aspect ratio Using the favorite channel search feature To scan and tune your favorite channelsDigital channels will not display in the POP multi-windows Resetting the picture settings Adjusting the pictureSelecting the picture mode Adjusting the picture quality To turn on the flesh tone feature To activate the ALSTo deactivate the ALS Using CableClear DNR digital noise reduction Selecting the color temperatureResetting the advanced picture settings Advanced closed captions Using the closed caption mode To listen to stereo sound Adjusting the audioMuting the sound Selecting stereo/SAP broadcasts Using the sub-bass system SBS Adjusting the audio quality Using the StableSound feature Using the SRS WOW surround sound featureResetting your audio adjustments Turning off the built-in speakers Selecting the Audio OUT soundSelecting the optical audio output format Using Memory card picture viewer Memory card specificationsViewing digital photos on your TV To close the picture viewer Using the memory card picture viewerMemory card care and handling To set the slide show interval Setting the sleep timer Setting the ON/OFF timer Understanding the last mode memory feature Displaying TV setting information on-screenViewing the demo mode Understanding the auto power off feature Changing your PIN code Using the Locks menuEntering the PIN code If you cannot remember your PIN code Edit Rating Limits screen below appears Blocking TV programs and movies by rating V-ChipTo block and unblock TV programs and movies Press z to highlight Edit Rating Limits and press Blocking channels Unlocking programs temporarilyLocking video inputs Using the front panel lock feature Using the game timer Troubleshooting Closed caption problems If Audio OUT is set to POP in the Audio Setup menuSound may be muted. Press Volume Set to SAP mode Setup Questions TV Guide On Screen FAQs Operational Questions Why won’t my VCR turn on? How do I resize or close the Info window? Edid = Enhanced-Extended Display Identification Appendix For 27 FST Pure and All Larger Television Models Limited United States Warranty How to Obtain Warranty Services Limited Canada Warranty Copyright 2003 Toshiba CORPORATION. All rights reserved Copyright 2003 Toshiba CORPORATION. All rights reserved Picture-out-picture POP Picture adjustmentsIndex Channel programming On/off Remote control 03-07 R 23565982 Manufactured by