Cleaning charger | Toshiba e-STUDIO206, e-STUDIO166 specs

Cleaning charger

If the inside of the charger is dirty, staining may appear on the copied image. Clean the charger following the procedure below.

1 Open the front cover.

2 Clean the charger.

Hold the cleaning knob of the charger and pull it out toward you carefully until it comes to a stop. Then reinsert it in its original position carefully. Repeat this procedure two or three times.

Check if the cleaning knob is fully inserted after cleaning.

3 Close the front cover.

Daily Inspection 101

Image 103

Toshiba e-STUDIO206, e-STUDIO166 manual Cleaning charger, Open the front cover Clean the charger

Contents

Operators Manual for Copying Functions Page Preface Preface Working environment For Germany onlyPage Lineup of our manuals Before Reading This Manual Description of original/paper direction How to read this manual Signal in this manual Trademarks Contents 100 Copying in Same Page Order as Originals Sort Copying 111 Cleaning charger 101 Cleaning transfer charger 102 Contents Toner remaining check function Toshiba Quality Is Second to NoneRecommended toner cartridges Cartridge detecting function Toner Supplies / PartsGeneral Functions extended by various options Features of e-STUDIO166/206Ecological energy-saving design When installing or moving General Precautions 10 cm 80 cm Other points When using the equipment Position of Certification label, etc When handling supplies During maintenance or inspection Poration Disclaimer Notice Energy Star programme Environmental Information Description of Each Component Preparation 1 Turning Power onPreparation 2 Placing Copy Paper Automatic Document Feeder optional, MR-2017 Description of Each ComponentFront / Right side Platen Cover Left side / Inner side Platen sheet USB terminal 4-pinReceiving tray Scanning area Original scale Configuration of options Control panel Copy qty. / zoom display selecting button/lamp Original mode button/lampsDensity adjustment buttons/lamps LED display Original button/lamps Original setting lampDrawer button/lamps Copy button/lamps Turning power on Preparation 1 Turning Power onTurning power OFF To turn the equipment into the energy saving mode manually Saving energy when not in use Energy saving modeCancelling the energy saving mode Acceptable media types Preparation 2 Placing Copy PaperFeeder Media type Paper size Maximum sheet Capacity *1 Media type Product name Recommended paperPaper types not acceptable Storing paper Press down the paper plate Placing paper in drawers Widen the gap with both hands Place paper in the drawer Adjust the side guides to the desired paper size Register the paper size into the equipment Do not let your fingers be caught when closing the drawer Registering standard size A3, A4, A4-R, A5-R, B4 Preparation 3 Registering Size of Paper Placed Code No Registering other standard sizes Preparation 3 Registering Size of Paper Placed Press the Start button Placing Originals Using Bypass TrayMaking Copies Acceptable originals When the built-in memory has become full during scanningSetting position Type of origi Placing Originals Placing originals on the original glass Placing booklet-type originals such as books or catalogues Media types Maximum size Maximum number Paper weight Using Automatic Document Feeder optionalPrecautions for Automatic Document Feeder optional When black streaks appear on the copied image Placing originals on Automatic Document Feeder optional When placing a large amount of originals with a long width Select the copy modes as required Making CopiesCheck if paper is placed in the drawer Place the original Press the CLEAR/STOP button during scanning or copying When the number of sheets exiting has exceededWhen the paper has run out Stopping/Resuming copying Press the Interrupt button Interrupting copying and making another copy Interrupt copy Media type Paper size Maximum sheet Capacity *1 Using Bypass Tray Preparation Registering paper size placed on bypass tray ST-R Folio Comp Using Bypass Tray Press the Start button Bypass copying on standard size paper Placed on the bypass tray is lit Using Bypass Tray Page Zooming In/Out Copy Image Default Settings Paper SelectionAutomatic paper selection APS Manual paper selection Contents Default setting at installation Default Settings Automatic paper selection APS Paper SelectionAutomatic paper selection APS Place the original on the Automatic Document Feeder Place paper in the drawer Place the original Manual paper selection Selecting the drawer of the equipment Specifying reproduction ratio manually Zooming In/Out Copy ImageAutomatic magnification selection AMS Automatic magnification selection AMS If the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Zooming in button until Specifying reproduction ratio manuallyPress Zooming out or Desired reproduction ratio appears Zooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Selecting Image Mode Dark Adjusting Density LevelTo adjust the density to the desired level To return it to the automatic copy density modePage Settings and Management of Equipment All lamps on Sound on All lamps off Sound off Switching Operation Sound On/Off Checking Total Number Copied Switch the display to check the rest of the total numberPress Button for more than two seconds Page When Message Lamp is Lit/Blinking Paper Jams Troubleshooting Toner lamp When Message Lamp is Lit/BlinkingCover open lamp Paper empty lamp Recommended toner cartridges Paper jam lamp Service call lamp Paper Jams When paper jams occur frequentlyChecking position of paper jams Do not tear jammed paper When releasing jammed paperPaper jams within Automatic Document Feeder optional Raise the lever, and then open the upper cover Paper Jams Pull out the paper jammed on the bypass tray Paper jams on bypass tray Paper jam behind transfer unit Close the transfer unit and the side cover Paper jams within fuser unit Paper Jams Paper jams within Paper Feed Unit optional Open the front cover Replacing Toner CartridgeHold down the green lever Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire General operation Before Calling Service TechnicianPhenomenon Usual cause Countermeasure Original/Copy paper-related items Toner-related items Image trouble Tion Charger is dirty Clean the charger Page Daily Inspection 100 Maintenance and Inspection Original glass Guides Platen sheet Daily Inspection Open the front cover Clean the charger Cleaning charger Cleaning transfer charger Daily Inspection Page Specifications and Options OPC STUDIO166/206 Specifications Paper size Feeder STUDIO166 STUDIO206 Continuous copying speed Automatic Document Feeder Specifications of OptionsPaper Feed Unit Packing List Page Index 106 DP-1660/2060 OME06015700 Multifunctional Digital Systems