Toshiba MR-3022, MR-3018 instruction

8

+5V TLENGTH-S SG TWIDTH0-S TWIDTH1-S TWIDTH2-S SG

CN73

		+5V	1
		TLENG-S	1
	1	TLENG-S	2	J85
	1	SG	2	J85
	2	SG	3
	2		3
	3
J73	4			Gray
	5		Yellow
	6		Orenge
	7			Black
	+5V	+5V

S1

S2

Original tray sensor

Original tray width sensor

MR-3018/3020/3021/3022 CIRCUIT DIAGRAM / HARNESS DIAGRAM

CN80 Not used

+5V ALIGN-S SG +5V

WIDTH2-S SG +5V

WIDTH1-S

CN74

	1				12			1									1
	1		ALIGN		12			1							ALIGN		1
	2		ALIGN		11			2							ALIGN		2	J88
	2		SG		11			2							SG		2	J88

	3				10			3									3
	3		+5V		10			3									3

	4				9			4							+5V
	5		WIDTH2		8			5							+5V		1
	5				8			5									1
	6		SG		7	J86	J86	6							WIDTH1		2	J89
	7		+5V		6	J86	J86	7							SG		3

			WIDTH1
J74	8		WIDTH1		5			8							+5V

			SG

S5

S6

Original registration sensor

Original width detection sensor-1

SG +5V LENGTH-S SG

-

CN82 Not used+5V

DFOPEN-S SG

CN83 Not used

+5V EMPTY-S SG +5V

JCOVU-S SG +5V EXIT-S SG +5V

READ-S SG +5V MID-S SG

PWA-F-DLG-623

CN75

	9															4			9																					1
	9													+5V		4			9																	WIDTH2				1
	10													+5V		3					10															WIDTH2				2	J90
	11											LENGTH				2					11																SG			3
	12													SG		1					12					+5V
	13																								LENGTH				12							1
																									LENGTH
	14																									SG			11		J91				J91	2
	15																									SG			10							3
	16																																				+5V
																																					+5V
																																				DFOPEN-S				1
																																				DFOPEN-S				2	J87
																																					SG			2	J87

																																								3
																																					+5V			3
																																					+5V
	1															6				1																EMPTY-S				1
	2															5				2																EMPTY-S				2	J96
	2															5				2																	SG			2	J96

	3															4	J92			3																				3
	3															4				3																				3
																			J92
	4															3			J92	4																	+5V
	5															2				5																JCOVU-S				1

	6															1				6																				2	J97
	6															1				6																				2	J97
	7																																				SG			3

J75	8
	9																								+5V
	9
	10																												12							1
																									EXIT-S				12							1
	11
	11																												11	J93					J93	2
	12																									SG			10							3
																													10							3
	13
	13
	14																								+5V
	14																								+5V
	15																								READ-S				12							1
																										SG			11	J94					J94	2

																													10							3
																									+5V				10							3


																									MID-S				12							1
																													11	J95					J95	2
																										SG			11	J95					J95	2

																													10							3
																													10							3

S7

S4

S12

S3

S11

S10

S9

S8

Original width detection sensor-2

Original length detection sensor

RADF opening/closing sensor

Original empty sensor

Jam access cover sensor

Original exit/reverse sensor

Read sensor

Original intermediate transport sensor

8 - 3 11/04

© 2005 - 2011 TOSHIBA TEC CORPORATION All rights reserved

Image 101

Toshiba MR-3022, MR-3018 service manual 2005 2011 Toshiba TEC Corporation All rights reserved

Contents

MR-3018/3020/3021/3022 11/12 Trademarks 11/12 Page Contents Rewriting ROM Firmware Updating Circuit Diagram / Harness Diagram MR-3018/3020 MR-3021/3022 Specifications Specifications 06/09 Main ComponentsLocation Components Sectional View S12 Electric Parts LayoutS11 S7 S6 S5 S8S4 S10 Sensors and Switches Symbols and Functions of Various ComponentsMotors Solenoid Diagram of Signal Blocks Description of Interface Signals Read motor drive section OutlineFeed motor drive section Original feed motor drive section Intermediate transfer roller Read motor drive section Gate solenoid Reverse flap Exit/reverse motor Original exit/reverse motor drive sectionReverse Exit/reverse roller Original tray width sensor Original Size Detection= high level Open = low level Short Original width size A4 series width sizes mixed at B4 / B5 standard A4 series width sizes mixed at A3 / A4 standardA4 series width sizes mixed at A4-R standard A4 series width sizes mixed at B5-R standard LT series width sizes mixed at LG / LT-R standard LT series ORG-SRSLT series width sizes mixed at LD / LT standard Cover OPEN? All sensors OFF? Power on Standby Radf jam accessEmpty sensor ON? Jam Certain period Time passed? OriginalRead motor rotates Registration roller rotates. Feed motor rotates reverse Certain period Scanning start signalDuplex? Sent level High Jam Read sensor OFF? Original exit/reverse Sensor ON?Certain period Time passed? Read motor stops Certain period Time passed? Gate solenoid on Scanning start signal sent level Low Scanning completed Read motor and exit/reverse motor rotate at requested speed Transport request Signal received?Jam Original exit/reverse motor and read motor stop Sensor OFF? Exposure and scanning start OriginalScanning completed Jam Original exit/reverse Sensor OFF? Original exit/reverse motor and read motor stopOriginal intermediate Transport sensor ON? Drive Circuit for Feed Motor Description of Circuit Drive Circuit for Read Motor Drive Circuit for FAN Motor Drive Circuit for Exit Motor Drive Circuit for Pickup Solenoid Reset Circuit Drive Circuit for Gate Solenoid Front cover CoverFront cover Rear cover Jam access coverRear cover Pin Remove 1 screw and the hinge pin Take off the jam access cover by sliding itLeft cover Left cover Original tray Original reverse tray Original reverse tray Paper feeder unit RollerRemove 1 clip and slide 2 bushings Take off the paper feeder unit Feed roller PM Pickup roller PMShaft Clip Pickup roller Pull out the shaft and take off the feed roller Slide the pulley and remove 1 pinPulley Shaft Separation roller PM Stay Take off the jam access guideFeeder lower guide Exit/reverse roller Registration roller Exit/reverse roller Exit guide Intermediate transport roller Pre-reading guideHinge pin Pre-reading guide Pre-reading roller ConnectorPost-reading roller Screw Bushing Bushing Flange Bearing BushingHolder Platen guide Upper guide Reverse registration rollerPost-reading roller Ring Roller Open the RADF. Take off the reverse regis- tration roller Fan motor M4 Motor / Motor drive sectionRead motor M2 Read motor Spring Read motor drive sectionSpring Harness clamp Take off 1 timing belt and 4 bushings Remove 3 screws and then take off the bracketTiming belt Screw Tensioner Ring Original feed motor drive section Original feed motor M1 Ring Bushing Bracket White Black Take off the timing belt, bushings and pulleyRed 09/01 Original exit/reverse motor M3 Disconnect 1 connector from the Radf conOriginal feed motor drive Section Original pickup solenoid SOL1 SolenoidOriginal pickup solenoid Bracket Gate solenoid Gate solenoid SOL2Mark-off line Original tray width sensor S2 Sensor/switch Original tray sensor Original tray sensor S1Release 2 latches and take off the original tray sensor Jam access cover sensor Jam access cover sensor S11Original empty sensor S3 Metal plate cover Original empty sensor Original length detection sensor Remove 2 screws and take off the bracketOriginal length detection sensor S4 Take off the feeder lower guide Feeder lower guide Original registration sensor S5Original width detection sensor-1 S6 Original width detection sensor-2 S7 Take off the pre-reading upper guide Pre-reading guide Read sensor S9Original intermediate transport sensor S8 Original exit/reverse sensor S10 Original exit/reverse sensor Take off the original jam access cover Original jam access cover opening/closing switch SW1Radf opening/closing sensor S12 Disconnect 3 terminals. Remove 1 screw ADF board PC BoardRadf control PC board ADF board Hinge stopper OthersRemove 1 screw and then take off the hinge Stopper Disassembly and Assembly Checking Adjustment of Position Adjustment 05/12 05/12 Install the bracket on the left-hand hinge Install the right-hand hinge screw at the rearSide MR-3021/3022 only 05/12 ~0.5mm 0mm Adjustment of Height Turn it clockwise Turn it counterclockwise Heightened 19 Chart Original Adjustment of Skew Adjustment Simplex copying 05/12 26 Chart Original Adjustment of the Leading Edge Position Adjustment 11/12 Adjustment of Horizontal Position 11/12 Adjustment of Copy Ratio 11/12 Adjustment of Radf Opening/Closing Sensor Adjustment Troubleshooting for Mechanical Errors Troubleshooting Check or replace the Radf board Troubleshooting for Electrical Errors Jam Feed signal reception jamJam not reaching the original registration sensor Jam not reaching the read sensor Stop jam at the original registration sensor Radf jam access cover open jamStop jam at the read sensor Stop jam at the original exit/reverse sensor 11/04 Radf open jamCover open jam in the read ready status 09/05 Symbols used in the checklist Periodic Maintenance Rewriting ROM Firmware Updating Component side Soldered side Assembly of PC Board Circuit Diagram 2005 2011 Toshiba TEC Corporation All rights reserved 1 MR-3018/3020 Control PC Board Circuit Circuit Diagram / Harness Diagram Circuit Diagram / Harness Diagram Circuit Diagram / Harness Diagram Circuit Diagram / Harness Diagram Circuit Diagram / Harness Diagram 2 MR-3021 11 09/05 09/05 13 09/05 09/05 15 09/05 3 MR-3022 17 09/05 09/05 19 09/05 09/05 21 09/05 Circuit Diagram / Harness Diagram