Slide the pulley and remove 1 pin, Pulley, Shaft | Toshiba MR-3018

(3)Slide the pulley and remove 1 pin.

Pin

Pulley

Fig. 4-20

(4)Pull out the shaft and take off the feed roller.

Feed roller

Shaft

Fig. 4-21

Note:

Make sure you assemble the feed roller with the one-way clutch in the correct direction.

LockLock

Fig. 4-22

MR-3018/3020/3021/3022	© 2005 - 2011 TOSHIBA TEC CORPORATION All rights reserved
DISASSEMBLY AND ASSEMBLY

4 - 8

05/12

Image 42

Toshiba MR-3018, MR-3022 Slide the pulley and remove 1 pin, Pull out the shaft and take off the feed roller, Pulley, Shaft

Contents

MR-3018/3020/3021/3022 Trademarks 11/12 11/12 Page Contents Circuit Diagram / Harness Diagram Rewriting ROM Firmware Updating Specifications MR-3018/3020 MR-3021/3022 Specifications Main Components Location Components06/09 Sectional View S11 S7 S6 S5 Electric Parts LayoutS12 S8S4 S10 Motors Symbols and Functions of Various ComponentsSensors and Switches Solenoid Diagram of Signal Blocks Description of Interface Signals Outline Feed motor drive sectionRead motor drive section Original feed motor drive section Read motor drive section Intermediate transfer roller Reverse Original exit/reverse motor drive sectionGate solenoid Reverse flap Exit/reverse motor Exit/reverse roller = high level Open = low level Short Original Size DetectionOriginal tray width sensor Original width size A4 series width sizes mixed at A4-R standard A4 series width sizes mixed at A3 / A4 standardA4 series width sizes mixed at B4 / B5 standard A4 series width sizes mixed at B5-R standard LT series ORG-SRS LT series width sizes mixed at LD / LT standardLT series width sizes mixed at LG / LT-R standard Empty sensor ON? Power on Standby Radf jam accessCover OPEN? All sensors OFF? Jam Read motor rotates OriginalCertain period Time passed? Registration roller rotates. Feed motor rotates reverse Duplex? Scanning start signalCertain period Sent level High Certain period Time passed? Original exit/reverse Sensor ON?Jam Read sensor OFF? Read motor stops Certain period Time passed? Scanning start signal sent level Low Scanning completed Gate solenoid on Transport request Signal received? Jam Original exit/reverse motor and read motor stopRead motor and exit/reverse motor rotate at requested speed Exposure and scanning start Original Scanning completedSensor OFF? Original exit/reverse motor and read motor stop Original intermediate Transport sensor ON?Jam Original exit/reverse Sensor OFF? Description of Circuit Drive Circuit for Feed Motor Drive Circuit for Read Motor Drive Circuit for Exit Motor Drive Circuit for FAN Motor Reset Circuit Drive Circuit for Pickup Solenoid Drive Circuit for Gate Solenoid Cover Front coverFront cover Rear cover Jam access coverRear cover Pin Left cover Take off the jam access cover by sliding itRemove 1 screw and the hinge pin Left cover Original tray Original reverse tray Original reverse tray Remove 1 clip and slide 2 bushings RollerPaper feeder unit Take off the paper feeder unit Shaft Pickup roller PMFeed roller PM Clip Pickup roller Pulley Slide the pulley and remove 1 pinPull out the shaft and take off the feed roller Shaft Separation roller PM Take off the jam access guide Feeder lower guideStay Registration roller Exit/reverse roller Exit guide Exit/reverse roller Hinge pin Pre-reading guideIntermediate transport roller Pre-reading guide Post-reading roller ConnectorPre-reading roller Screw Bushing Holder Flange Bearing BushingBushing Platen guide Post-reading roller Reverse registration rollerUpper guide Ring Open the RADF. Take off the reverse regis- tration roller Roller Read motor M2 Motor / Motor drive sectionFan motor M4 Read motor Spring Read motor drive sectionSpring Harness clamp Timing belt Remove 3 screws and then take off the bracketTake off 1 timing belt and 4 bushings Screw Tensioner Ring Original feed motor M1 Original feed motor drive section Red Take off the timing belt, bushings and pulleyRing Bushing Bracket White Black 09/01 Original feed motor drive Disconnect 1 connector from the Radf conOriginal exit/reverse motor M3 Section Original pickup solenoid SolenoidOriginal pickup solenoid SOL1 Bracket Gate solenoid SOL2 Mark-off lineGate solenoid Sensor/switch Original tray width sensor S2 Original tray sensor S1 Release 2 latches and take off the original tray sensorOriginal tray sensor Original empty sensor S3 Jam access cover sensor S11Jam access cover sensor Metal plate cover Remove 2 screws and take off the bracket Original length detection sensor S4Original empty sensor Original length detection sensor Original width detection sensor-1 S6 Original registration sensor S5Take off the feeder lower guide Feeder lower guide Original width detection sensor-2 S7 Original intermediate transport sensor S8 Read sensor S9Take off the pre-reading upper guide Pre-reading guide Original exit/reverse sensor S10 Original exit/reverse sensor Radf opening/closing sensor S12 Original jam access cover opening/closing switch SW1Take off the original jam access cover Disconnect 3 terminals. Remove 1 screw PC Board Radf control PC board ADF boardADF board Remove 1 screw and then take off the hinge OthersHinge stopper Stopper Disassembly and Assembly Adjustment of Position Checking Adjustment 05/12 05/12 Side Install the right-hand hinge screw at the rearInstall the bracket on the left-hand hinge MR-3021/3022 only 05/12 Adjustment of Height ~0.5mm 0mm Turn it counterclockwise Heightened Turn it clockwise Adjustment of Skew 19 Chart Original Adjustment Simplex copying 05/12 Adjustment of the Leading Edge Position 26 Chart Original Adjustment 11/12 Adjustment of Horizontal Position 11/12 Adjustment of Copy Ratio 11/12 Adjustment of Radf Opening/Closing Sensor Adjustment Troubleshooting Troubleshooting for Mechanical Errors Troubleshooting for Electrical Errors Check or replace the Radf board Jam not reaching the original registration sensor Feed signal reception jamJam Jam not reaching the read sensor Stop jam at the read sensor Radf jam access cover open jamStop jam at the original registration sensor Stop jam at the original exit/reverse sensor Radf open jam Cover open jam in the read ready status11/04 09/05 Periodic Maintenance Symbols used in the checklist Rewriting ROM Firmware Updating Assembly of PC Board Component side Soldered side Diagram Circuit 2005 2011 Toshiba TEC Corporation All rights reserved Control PC Board Circuit 1 MR-3018/3020 Circuit Diagram / Harness Diagram Circuit Diagram / Harness Diagram Circuit Diagram / Harness Diagram Circuit Diagram / Harness Diagram Circuit Diagram / Harness Diagram 2 MR-3021 11 09/05 09/05 13 09/05 09/05 15 09/05 3 MR-3022 17 09/05 09/05 19 09/05 09/05 21 09/05 Circuit Diagram / Harness Diagram