Connecting video equipment | Toshiba TLP-X10Y, TLP-X20E, TLP-X21E

Connecting video equipment

You can project the picture from video equipment by using VIDEO IN connectors.

Check that the power for the projector and video equipment is off before connecting the cables.

CONTENTS

24

CONTROL USB	MONITOR OUT		COMPUTER IN 1		COMPUTER IN 2
			( Y/PB/PR )
	AUDIO	AUDIO		VIDEO IN
	OUT	IN	R - AUDIO - L		VIDEO S-VIDEO

S-VIDEO connector

At shipping from factory, the projector is set so that this connector cannot be selected by the INPUT button.

Change the setting on the menu screen when using. 48

Installation and connection

TER

IN 2

PU

COM

TER

IN 1

PU

R )

COM B/P

( Y/P

T

OR

OU

NIT

MO

B

US

TROL

CON

IN

S-

VID

EO

EO

VID

VID

AUDI

O -

L

DIO

R -

AU

AU

DIO

IN

OUT

To S-VIDEO connector

Be sure to connect in the proper direction.

To S-video output

S-video cable (not supplied)

Video equipment

Pin plug (red)

To audio output (R)

(Red) To AUDIO-R jack

(White) To AUDIO-L jack

(Yellow) To VIDEO jack

AV cable (supplied)

Pin plug (white)

To audio output (L)

Pin plug (yellow)

To video output

Note

The S-VIDEO connector and VIDEO jack can be used independently, but the audio input jacks are used as both the S-VIDEO and VIDEO input.

Continued

Image 24

Toshiba TLP-X10Y, TLP-X20E, TLP-X21E, TLP-X20Y, TLP-X21Y, TLP-X10E, TLP-X11E, TLP-X11Y owner manual Connecting video equipment

Contents

TLP-X10E Safety Precautions Save Original Packing Materials Avoid Volatile LiquidMoisture Condensation Power Sources Source of LightVentilation Important Safety Instructions Accessories Object and Liquid EntryDo not place the product vertically Stack Inhibited Important Safety Instructions Damage Requiring ServiceReplacement Parts Servicing Safety Check Do not carry by the camera armDo not move the projector while the arm is still erect Strong light may cause damage to your eyes or sight Power supply cord selection Contents Names of each part on the main unit Use VOL/ADJ buttons 30 41 48 Control connector RS-232C Connector 26 USB connector Use Names of each part on the remote control Laser emission part Install the batteries Loading batteriesOpen the cover Attach the cover Remote control operation Before Floor-mounted projector placement Determine the screen size projected on the screen Side view Connect the power cord Take off the lens coverInsert the other end in a wall outlet Projector placement angle adjustment Turn clockwise to lift up Turn counterclockwise to lower Ceiling-mounted projector placement Installation and connection Connecting a computer Connecting a computer with DVI output connector Computer in 2 Connector DVI connector Connecting video equipment RGB2/digital RGB and Y/P B/P R input Projector operation control by a computer How to use the output connector Playback mode Projection on the screenPress ON/STANDBY Turn on the connected equipment and put it Signal sent from the computer Select the input source Adjust the picture size by turning Focusing ringPress VOL/ADJ +/ to adjust volume Zooming lever Turning the power off Press ON/STANDBY after using the projectorPress ON/STANDBY again Adjusting the picture automatically Press Auto SET Correcting the keystone distortion Press Auto Keystone Remote control Cutting off the picture and sound temporarilyPress Mute Operations Icon Appears in the freeze mode Freezing the picturePress Freeze Picture freezes Icon Appears in the resize mode Enlarging the picture sizePress Resize Displaying PIP Sub-pictures Press PIPSub-picture is displayed Displaying Information Press CallInformation described below is displayed Pressed again Operating a computer by the remote control Projecting images stored in a memory card About memory cards Insert the memory card into the card slot Press Input repeatedly to select the memory card input Remote control Control panel Description of screenUse VOL/ADJ +/ to change pages. Changing Press ENTER. Slide display Press VOL/ADJ +/-. Slide transitionPress Exit Projecting images stored in a memory card To eject the memory card Adjustments and settings on the menu screen Quick Menu Adjustments and settings on the menu screen Operating the menu screen Start Quick Menu adjustments and settings Press MenuQuick Menu appears Types of adjustment and setting items are different See the table below Press VOL/ADJ +/ to adjust and set Picture mode Analog RGB input, digital RGB inputLamp power Auto. demo Memory card input Sub-menu screen of input source setting appears Press EnterPress VOL/ADJ +/- to select the type of input source Press Exit to return to the Quick Menu Use the selection buttons / to select a language Sub-menu screen of interval setting appears Use the selection buttons / to select interval timeMenu screen disappears Full Menu adjustments and settings -Picture AdjustmentsPress Menu twice Full Menu adjustments and settings Picture Picture mode RGB input Input select mode Memory card inputScreen size Slide show Memory card input Press Exit to return to the Full Menu Sub-menu of selected items appears PositionLevel Use the selection buttons / to select setting items Signal format Y/PB/PR inputVideo mode Video input, S-video input Sub-menu of selected items appears Full Menu adjustments and settings Picture Full Menu settings Audio After the settings are finished, press Exit Speaker outputChannel select Loudness Full Menu settings Keystone Use the selection buttons To select Setting itemsUse the selection buttons To display Keystone menu After the adjustments and settings are finished Use the selection buttons / to select Yes and press EnterPress Exit several times until the menu screen Disappears Full Menu settings Display Use the selection buttons To select Setting items SettingsWhen pressed once, the Quick Menu screen appears. When Use the selection buttons To display Display menu When selecting Language in step No signal background Setting of screen of no signal input Menu positionMenu background translucent Start-up screen Full Menu settings Default setting Use the selection buttons To display Default setting menuWhen pressed once, the Quick Menu screen appears. When Sub-menu of Input source setting appears Control panel Main unit side Use the selection buttons / to select the projection mode Sub-menu of Projection mode appearsRear ceiling Ceiling-mounted rear projection No signal power off Power onPress VOL/ADJ +/ to set Full Menu settings Factory reset mode Factory default settingPicture menus for the each input to Full Menu settings Factory reset mode PIP menu setting Size Set the PIP sub-picture sizeAudio Set the audio input source Menu screen disappears Part names of the document imaging camera model Preparation of the document imaging camera Press ARM Light Set a document to be projectedCamera control panel Light turns on Press Camera to select the camera input mode Move the camera head to adjust the size Picture Press Camera Gain +/- to improve view of a Camera subject which is too dark or vividFollow the steps of Preparation of the document imaging Camera in reverse Balance Press W.BALANCE to turn the Lock indicator Lock the white balanceProject a white paper and enlarge it to fill Screen Correcting illuminated defects With the document camera operating, fullyCover the camera lens with a piece of black Paper or cloth Store the camera images into the memory card Indicator Power does not come onPower turns off or does not come on Trouble indications Air filter cleaning Unplug the power cordClean the air filter Take off the air filter cover Air filter cleaning Install itAssemble the air filter Mount the air filter cover Lens and main unit cleaning Cleaning the lensCleaning the main unit Replacing the intake, exhaust fans and air filter Lamp replacement Pull out the lampLoosen two screws, and pull off the lamp cover Handle to pull out the lamp Reset the lamp timer Load a new lampAttach the lamp cover Slide the cover in place and tighten two screws Before calling service personal Symptom Cause Correction Before calling service personal Pin assignment of Computer IN, Monitor OUT connector Applicable signal Applicable RGB signal Applicable signal Compatible video signal Controlling the projector by using RS-232C Signal assignment of RS-232C Interface format Controlling the projector by using RS-232C AS1 MB1 VLU Auto SET Specifications Mini DIN 8-pin RS-232CUSB output Type B Specifications Replacement lamp