Manuals / TP-Link / Computer Equipment / Network Router

TP-Link 1910010933 manual Daylight Saving Time, ¾ Config

Models: 1910010933

1 124

Download 124 pages 9.3 Kb

Page 115

¾ Config

Status:	Displays the status of time capturing.
¾ Config
Get UTC:	When this option is selected, you can configure the time zone and the
	IP address for the NTP server. The router will get UTC automatically if
	it has connected to an NTP server.
	z Time Zone: Select the time zone for the router.
	z Primary/Secondary NTP Server: Enter the IP address or domain
	name of the NTP server.
Manual:	With this option selected, you can set the date and time manually.
Synchronize with	With this option selected, the administrator PC’s clock is utilized.
PC’S Clock:

Note:

●If Get UTC function cannot be used properly, please add an entry with UDP port of 123 to the firewall software of the PC.

●The time will be lost when the router is restarted. The router will obtain UTC time automatically from Internet.

4.8.5.2Daylight Saving Time

On this page you can configure the Daylight Saving Time of the router.

Choose the menu Maintenance→Time→Daylight Saving Time to load the following page.

Figure 4-72 Daylight Saving Time

-110-

Image 115

TP-Link 1910010933 manual Daylight Saving Time, ¾ Config

Contents

REV6.0.0 1910010933 TL-R480T+ Load Balance Broadband RouterFCC STATEMENT COPYRIGHT & TRADEMARKSCE Mark Warning 安全諮詢及注意事項 Safety InformationChapter 1 About this Guide CONTENTSChapter 3 Quick Installation Guide Chapter 4 ConfigurationAppendix B Hardware SpecificationsGlossary Appendix APackage Contents 1.2 Conventions SymbolChapter 1 About this Guide 1.1 Intended ReadersAppendix C Glossary Appendix B FAQProvides the possible solutions to the problems that may occur during the installation and operation of the router2.1 Overview of the Router z Powerful Data Processing Capabilityz Powerful Firewall Chapter 2 IntroductionBasic Functions 2.2 Featuresz Easy-to-use Hardwarez LEDs 2.3 Appearance2.3.1 Front Panel Securityz Interface Description z Reset buttonz AC Power Receptacle 2.3.2 Rear Panel3.1 Configure PC Chapter 3 Quick Installation GuidePage Page Is the TCP/IP configuration for your PC correct? 3.2 LoginIs the connection between your PC and the router correct? Figure 3-9 WAN Mode Figure 3-8 Quick SetupFigure 3-11 WAN Connection Type Figure 3-10 WAN PortFigure 3-12 WAN Connection Type - PPPoE Figure 3-13 WAN Connection Type - PPPoE ConnectingFigure 3-15 WAN Connection Type - Static IP Figure 3-14 WAN Connection Type - Dynamic IPIf you have difficulty in this process, please contact your ISP Figure 3-17 Configuration Completed Figure 3-16 WAN Connection Type - Static IP Connecting4.1 Status Chapter 4 Configuration4.3 Network 4.2 Quick Setup4.3.1.1 WAN Mode ¾ WAN ModeTips 1 Static IP¾ Static IP Choose the menu Network→WAN→WAN1 to load the configuration pageSecondary DNS 2 Dynamic IPDefault Gateway Primary DNS¾ Dynamic IP Select this option to enter the DNS Domain Name Server address ¾ Dynamic IP Statusz “Connected” indicates that the router has successfully obtained Figure 4-5 WAN - PPPoE 3 PPPoEPrimary DNS Displays the IP address of your ISP’s Primary DNS Secondary DNS Displays the IP address of your ISP’s Secondary DNSEnter the Account Name provided by your ISP. If you are not clear ¾ PPPoE Settingson. The connection can be re-established automatically when it 576-1492. The default MTU is 1480. You are recommended to keepDynamic IP is selected, the obtained subnet address of WAN port is Here allows you to configure the secondary connection. Dynamic IPmanually terminated or the router gets no response from ¾ PPPoE StatusFigure 4-6 WAN - L2TP 4 L2TPEnter the Account Name provided by your ISP. If you are not ¾ L2TP SettingsSubnet Mask ¾ L2TP StatusDefault Gateway IP AddressDisplays the IP address of your ISP’s Secondary DNS 5 PPTPConnection Type ¾ PPTP SettingsPassword Active ModeUpstream Bandwidth ¾ PPTP StatusDefault Gateway Subnet Mask6 BigPond ¾ BigPond Settingsbeen ¾ BigPond Status4.3.2.1 LAN 4.3.2 LAN¾ LAN 4.3.2.2 DHCP ¾ DHCP Settings4.3.2.4 DHCP Reservation 4.3.2.3 DHCP Client¾ List of Reserved Address ¾ DHCP ReservationActivate or Inactivate the corresponding entry ¾ MAC Address 4.3.3 MAC AddressSet the MAC Address for LAN port Set the MAC Address for WAN port4.3.4.1 Statistics 4.3.4 Switch¾ Statistics 4.3.4.2 Port Mirror¾ Port Mirror ¾ GeneralApplication Example 4.3.4.3 Rate ControlTips ¾ Rate Control 4.3.4.4 Port Config4.3.4.5 Port Status ¾ Port ConfigTips 4.4 User Group4.3.4.6 Port VLAN ¾ Port VLAN¾ List of Group ¾ Group Config4.4.1 Group 4.4.2 User4.4.3 View ¾ User Config¾ List of User 4.5.1 NAT 4.5.1.1 NAT Setup¾ View Config 4.5 Advanced¾ NAPT 4.5.1.2 One-to-One NAT¾ NAT-DMZ ¾ List of Rules ¾ One-to-One NATActivate or inactivate the entry ¾ Multi-Nets NAT 4.5.1.3 Multi-Nets NAT¾ list of Rules Application Example Network Requirements Configuration procedure4.5.1.4 Virtual Server Protocol ¾ Virtual ServerStatus ¾ List of Rules 4.5.1.5 Port Triggering¾ Port Triggering 4.5.1.6 ALG¾ List of Rules 4.5.2 Traffic Control 4.5.2.1 Setup¾ ALG Default Limit applies only for users that are not constrained by Bandwidth ¾ Interface Bandwidth 4.5.2.2 Bandwidth Control¾ List of Rules ¾ Bandwidth Control RuleSelect the data stream direction for the entry. The direction of arrowhead 4.5.3.1 Session Limit 4.5.3 Session Limit¾ Session Limit 4.5.4.1 Configuration4.5.4 Load Balance 4.5.3.2 Session List4.5.4.2 Policy Routing ¾ General 4.5.4.3 Link Backup¾ List of Rules ¾ General ¾ List of Rules 4.5.4.4 Protocol¾ List of Protocol 4.5.5 Routing4.5.5.1 Static Route ¾ Protocol¾ List of Rules ¾ Static RouteApplication Example Network Requirements Configuration procedure4.6.1 Anti ARP Spoofing 4.6 Firewall4.6.1.1 IP-MAC Binding Status ¾ IP-MAC Binding¾ General IP Address¾ List of Rules 4.6.1.2 ARP Scanning4.6.1.3 ARP List 4.6.2 Attack DefenseThe following items are displayed on this screen Figure 4-41 Attack Defense¾ General Packet Anomaly 4.6.3 MAC Filtering¾ MAC Filtering Enable Attack¾ General 4.6.4 Access Control4.6.4.1 URL Filtering ¾ List of RulesApplication Example Network Requirements Configuration Procedure¾ URL Filtering Rule ¾ List of Rules4.6.4.2 Web Filtering 4.6.4.3 Access RulesService ¾ Access RulesPolicy ¾ List of Rules ¾ Service 4.6.4.4 Service4.6.5 App Control ¾ List of Service4.6.5.1 Control Rules ¾ List of Rules 4.6.5.2 Database¾ Control Rules ¾ General4.7.1 PPPoE Server 4.7 Services4.7.1.1 General ¾ General PPPoE Server Specify whether to enable the PPPoE Server function¾ List of IP Pool 4.7.1.2 IP Address Pool4.7.1.3 Account ¾ IP Address PoolAccount Name Password IP Address Assigned Mode Static IP Address ¾ AccountIP Address Pool Max Sessions 4.7.1.4 Exceptional IP is 48. If Enable Advanced Account Features is not selected, the¾ List of Account ¾ Exceptional IP 4.7.1.5 List of Account¾ List of Account ¾ General 4.7.2 E-BulletinInterval Tips 4.7.3 Dynamic DNS¾ E-Bulletin ¾ List of E-Bulletin4.7.3.1 DynDNS ¾ Dyndns DDNS 4.7.3.2 No-IP¾ List of DynDNS Account ¾ List of No-IP Account ¾ No-IP DDNS¾ PeanutHull DDNS 4.7.3.3 PeanutHull¾ List of PeanutHull Account 4.7.3.4 Comexe¾ Comexe DDNS 4.7.4 UPnP¾ List of Comexe Account On this page you can configure UPnP service ¾ List of UPnP Mapping¾ General ¾ Administrator 4.8 Maintenance4.8.1 Admin Setup 4.8.1.1 Administrator¾ General 4.8.1.2 Login ParameterApplication Example Network Requirements ¾ Remote Management 4.8.1.3 Remote ManagementConfiguration Procedure ¾ List of Subnet 4.8.2.1 Factory Defaults4.8.2 Management 4.8.2.2 Export and Import¾ Export 4.8.2.3 Reboot4.8.2.4 Firmware Upgrade ¾ Configuration Version4.8.3.1 Interface Traffic Statistics 4.8.3 Statistics¾ Interface Traffic Statistics ¾ IP Traffic Statistics 4.8.3.2 IP Traffic Statistics¾ Advanced WAN Information ¾ Traffic Statistics4.8.4.1 Diagnostics 4.8.4 Diagnostics¾ General 4.8.4.2 Online Detection¾ Ping ¾ Tracert¾ Current Time 4.8.5 Time4.8.5.1 Time ¾ List of WAN status4.8.5.2 Daylight Saving Time ¾ Config4.8.6 Logs ¾ Daylight Saving TimeDST Config¾ Daylight Saving TimeDST State Severity ¾ List of LogsLevel ¾ ConfigTransmission Medium Appendix A Hardware SpecificationsPower PortsAppendix B FAQ 4. Make sure that the NAT DMZ service is disabled Glossary Appendix C GlossaryDescription Glossary for services such as IPSec that require keys. Before any IPSecDescription Description GlossaryDescription GlossaryTelnet is used for remote terminal connection, enabling users to