Manuals / TP-Link / Computer Equipment / Network Router

TP-Link 1910010933 manual Application Example Network Requirements, Configuration procedure

Models: 1910010933

1 124

Download 124 pages 9.3 Kb

Page 58

Image 58

Application Example:

Network Requirements

The LAN subnet of TL-R480T+ is 192.168.0.0 /24, the subnet of VLAN2 under a three layer switch is 192.168.2.0 /24, while the subnet of VLAN3 is 192.168.3.0 /24. The IP of VLAN for cascading the switch to the router is 192.168.0.2. Now the hosts within VLAN2 and VLAN3 desire to access the Internet.

The network topology is shown as the following:

Configuration procedure

1.Establish the Multi-Nets NAT entries with Subnet/Mask of VLAN2 and VLAN3.

The configured entries are as follows:

-53-

Page 58

Image 58

TP-Link 1910010933 manual Application Example Network Requirements, Configuration procedure

Contents

TL-R480T+ Load Balance Broadband Router REV6.0.0 1910010933FCC STATEMENT COPYRIGHT & TRADEMARKSCE Mark Warning Safety Information 安全諮詢及注意事項Chapter 4 Configuration CONTENTSChapter 3 Quick Installation Guide Chapter 1 About this GuideAppendix A Hardware SpecificationsGlossary Appendix BPackage Contents 1.1 Intended Readers SymbolChapter 1 About this Guide 1.2 Conventionsthe installation and operation of the router Appendix B FAQProvides the possible solutions to the problems that may occur during Appendix C GlossaryChapter 2 Introduction z Powerful Data Processing Capabilityz Powerful Firewall 2.1 Overview of the RouterHardware 2.2 Featuresz Easy-to-use Basic FunctionsSecurity 2.3 Appearance2.3.1 Front Panel z LEDs2.3.2 Rear Panel z Reset buttonz AC Power Receptacle z Interface DescriptionChapter 3 Quick Installation Guide 3.1 Configure PCPage Page Is the TCP/IP configuration for your PC correct? 3.2 LoginIs the connection between your PC and the router correct? Figure 3-8 Quick Setup Figure 3-9 WAN ModeFigure 3-10 WAN Port Figure 3-11 WAN Connection TypeFigure 3-13 WAN Connection Type - PPPoE Connecting Figure 3-12 WAN Connection Type - PPPoEFigure 3-15 WAN Connection Type - Static IP Figure 3-14 WAN Connection Type - Dynamic IPIf you have difficulty in this process, please contact your ISP Figure 3-16 WAN Connection Type - Static IP Connecting Figure 3-17 Configuration CompletedChapter 4 Configuration 4.1 Status¾ WAN Mode 4.2 Quick Setup4.3.1.1 WAN Mode 4.3 NetworkChoose the menu Network→WAN→WAN1 to load the configuration page 1 Static IP¾ Static IP TipsPrimary DNS 2 Dynamic IPDefault Gateway Secondary DNS¾ Dynamic IP Select this option to enter the DNS Domain Name Server address ¾ Dynamic IP Statusz “Connected” indicates that the router has successfully obtained Secondary DNS Displays the IP address of your ISP’s Secondary DNS 3 PPPoEPrimary DNS Displays the IP address of your ISP’s Primary DNS Figure 4-5 WAN - PPPoE576-1492. The default MTU is 1480. You are recommended to keep ¾ PPPoE Settingson. The connection can be re-established automatically when it Enter the Account Name provided by your ISP. If you are not clearHere allows you to configure the secondary connection. Dynamic IP Dynamic IP is selected, the obtained subnet address of WAN port is¾ PPPoE Status manually terminated or the router gets no response from4 L2TP Figure 4-6 WAN - L2TP¾ L2TP Settings Enter the Account Name provided by your ISP. If you are notIP Address ¾ L2TP StatusDefault Gateway Subnet Mask5 PPTP Displays the IP address of your ISP’s Secondary DNSActive Mode ¾ PPTP SettingsPassword Connection TypeSubnet Mask ¾ PPTP StatusDefault Gateway Upstream Bandwidth¾ BigPond Settings 6 BigPond¾ BigPond Status been4.3.2.1 LAN 4.3.2 LAN¾ LAN ¾ DHCP Settings 4.3.2.2 DHCP4.3.2.3 DHCP Client 4.3.2.4 DHCP Reservation¾ List of Reserved Address ¾ DHCP ReservationActivate or Inactivate the corresponding entry Set the MAC Address for WAN port 4.3.3 MAC AddressSet the MAC Address for LAN port ¾ MAC Address4.3.4 Switch 4.3.4.1 Statistics4.3.4.2 Port Mirror ¾ Statistics¾ General ¾ Port MirrorApplication Example 4.3.4.3 Rate ControlTips 4.3.4.4 Port Config ¾ Rate Control¾ Port Config 4.3.4.5 Port Status¾ Port VLAN 4.4 User Group4.3.4.6 Port VLAN Tips4.4.2 User ¾ Group Config4.4.1 Group ¾ List of Group4.4.3 View ¾ User Config¾ List of User 4.5 Advanced 4.5.1.1 NAT Setup¾ View Config 4.5.1 NAT¾ NAPT 4.5.1.2 One-to-One NAT¾ NAT-DMZ ¾ List of Rules ¾ One-to-One NATActivate or inactivate the entry ¾ Multi-Nets NAT 4.5.1.3 Multi-Nets NAT¾ list of Rules Configuration procedure Application Example Network Requirements4.5.1.4 Virtual Server Protocol ¾ Virtual ServerStatus 4.5.1.5 Port Triggering ¾ List of Rules¾ Port Triggering 4.5.1.6 ALG¾ List of Rules 4.5.2 Traffic Control 4.5.2.1 Setup¾ ALG Default Limit applies only for users that are not constrained by Bandwidth 4.5.2.2 Bandwidth Control ¾ Interface Bandwidth¾ List of Rules ¾ Bandwidth Control RuleSelect the data stream direction for the entry. The direction of arrowhead 4.5.3 Session Limit 4.5.3.1 Session Limit4.5.3.2 Session List 4.5.4.1 Configuration4.5.4 Load Balance ¾ Session Limit4.5.4.2 Policy Routing ¾ General 4.5.4.3 Link Backup¾ List of Rules ¾ General 4.5.4.4 Protocol ¾ List of Rules¾ Protocol 4.5.5 Routing4.5.5.1 Static Route ¾ List of Protocol¾ Static Route ¾ List of RulesConfiguration procedure Application Example Network Requirements4.6.1 Anti ARP Spoofing 4.6 Firewall4.6.1.1 IP-MAC Binding IP Address ¾ IP-MAC Binding¾ General Status4.6.1.2 ARP Scanning ¾ List of Rules4.6.2 Attack Defense 4.6.1.3 ARP ListThe following items are displayed on this screen Figure 4-41 Attack Defense¾ General Enable Attack 4.6.3 MAC Filtering¾ MAC Filtering Packet Anomaly¾ List of Rules 4.6.4 Access Control4.6.4.1 URL Filtering ¾ General¾ List of Rules Configuration Procedure¾ URL Filtering Rule Application Example Network Requirements4.6.4.3 Access Rules 4.6.4.2 Web FilteringService ¾ Access RulesPolicy ¾ List of Rules 4.6.4.4 Service ¾ Service4.6.5 App Control ¾ List of Service4.6.5.1 Control Rules ¾ General 4.6.5.2 Database¾ Control Rules ¾ List of Rules4.7.1 PPPoE Server 4.7 Services4.7.1.1 General PPPoE Server Specify whether to enable the PPPoE Server function ¾ General¾ IP Address Pool 4.7.1.2 IP Address Pool4.7.1.3 Account ¾ List of IP PoolAccount Name Password IP Address Assigned Mode Static IP Address ¾ AccountIP Address Pool Max Sessions 4.7.1.4 Exceptional IP is 48. If Enable Advanced Account Features is not selected, the¾ List of Account ¾ Exceptional IP 4.7.1.5 List of Account¾ List of Account ¾ General 4.7.2 E-BulletinInterval ¾ List of E-Bulletin 4.7.3 Dynamic DNS¾ E-Bulletin Tips4.7.3.1 DynDNS ¾ Dyndns DDNS 4.7.3.2 No-IP¾ List of DynDNS Account ¾ No-IP DDNS ¾ List of No-IP Account4.7.3.3 PeanutHull ¾ PeanutHull DDNS4.7.3.4 Comexe ¾ List of PeanutHull Account¾ Comexe DDNS 4.7.4 UPnP¾ List of Comexe Account On this page you can configure UPnP service ¾ List of UPnP Mapping¾ General 4.8.1.1 Administrator 4.8 Maintenance4.8.1 Admin Setup ¾ Administrator¾ General 4.8.1.2 Login ParameterApplication Example Network Requirements ¾ Remote Management 4.8.1.3 Remote ManagementConfiguration Procedure 4.8.2.2 Export and Import 4.8.2.1 Factory Defaults4.8.2 Management ¾ List of Subnet¾ Configuration Version 4.8.2.3 Reboot4.8.2.4 Firmware Upgrade ¾ Export4.8.3.1 Interface Traffic Statistics 4.8.3 Statistics¾ Interface Traffic Statistics ¾ Traffic Statistics 4.8.3.2 IP Traffic Statistics¾ Advanced WAN Information ¾ IP Traffic Statistics4.8.4 Diagnostics 4.8.4.1 Diagnostics¾ Tracert 4.8.4.2 Online Detection¾ Ping ¾ General¾ List of WAN status 4.8.5 Time4.8.5.1 Time ¾ Current Time¾ Config 4.8.5.2 Daylight Saving Time4.8.6 Logs ¾ Daylight Saving TimeDST Config¾ Daylight Saving TimeDST State ¾ Config ¾ List of LogsLevel SeverityPorts Appendix A Hardware SpecificationsPower Transmission MediumAppendix B FAQ 4. Make sure that the NAT DMZ service is disabled Glossary Appendix C GlossaryDescription Glossary for services such as IPSec that require keys. Before any IPSecDescription Glossary DescriptionDescription GlossaryTelnet is used for remote terminal connection, enabling users to